hello again,
i have instaled to hyperion to version 2.0.12 stable in order to use with my old leds WS2812 but the leds wont work.
buut when i put the code
For ws281x PWM (attached to GPIO-18):
sudo systemctl disable --now hyperiond@pi
sudo systemctl enable --now hyperiond@root
i have the following msg can someone help m please.
Enter hyperiond in terminal, post output.
That doesn't seem to be installed or not fully installed.
regards pclin
Execute this command in terminal in case hyperiond is found:
sudo updateHyperionUser -u root
not correct (old)
sudo systemctl disable --now hyperiond@pi
sudo systemctl enable --now hyperiond@root
correct (new)
sudo systemctl disable --now hyperion@pi
sudo systemctl enable --now hyperion@root
But do what Lord-Grey wrote.
regards pclin
After i followed your steps the leds don’t (only the first led lighs up as you can see in the photo) work and I can not figured out why. Everything it’s ok i have check it several times.
So I have plug in green wire to gpio18 on the pi and white wire in ground on the pi as well then I have connected at the leds. Green and white
Please check below i you could see what is wrong 
I can't see any flaws in the pictures either.
What has changed since post #69 / #71?
Except for hyperion 2.0.12 where you have root rights for ws281x.
Post debug log and/or look for errors
regards pclin
What has changed since post #69 / #71?
What you mean?
In post #71 you write that everything works, what have you changed apart from the Hyperion update?
With the update you only had to run hyperion as root, after that everything has to work as before.
regards pclin
Debug log?
/boot/config.txt?
regards pclin
i dont see anything weird 
helo again and i m sorry for my persistance.
So after i have a few time available i make a fresh instalation on my sd card.
I have used the tutorial from DrZzs.
When i arrive to step i have put this command :
sudo dpkg -i Hyperion-2.0.13-Linux-armv7l.deb
i have this
then ater i put the command
sudo reboot
u put these 2 lines
sudo systemctl disable --now hyperion@pi
sudo systemctl enable --now hyperion@root
but the leds dont work.
i have tried some commands in order to see i i could see what is wrong and have this:
And this is what I have in my tv
PS: when i have put the command the fist time
sudo dpkg -i Hyperion-2.0.13-Linux-armv7l.deb
i have a msg error regardin to libcec6 so i have put:
sudo apt-get install libcec6
sudo apt-get install libcec-dev
apt --fix-broken install
but then i think it is installed as you can see in the 1st image above
i can someone give me some help i be thankfull.
i dont know what i can do in order to work it
Thanks a lot for the help
why u do the sudo su command?
And you install in root directory, so how I see it you are trying to start the hyperion service while it's already there and running.
hyperiond@pi.service applied to older hyperion versions!
hyperiond is the binary, the service is hyperion@username.service.
So systemctl status hyperion can't work either, systemctl status hyperion@username is correct.
If hyperion has to run under root, you go along with it
sudo updateHyperionUser -u root
regards pclin
thank a lot for your hep guys,
i have make a fresh intalation and same problem leds dont work
so after i used another tutorial on youtube same problem as before.
1- i have Download the image here: HyperBian Download
2 extract the image and burn on my sd card using raspberry pi image (select a custom image from my pc that i have extract)
3 after installation is finished put on the sd card ssh and wpa_supplicant.conf file
4 using putty put these commands
sudo systemctl disable --quiet hyperion@pi.service --now
sudo systemctl enable --quiet hyperion@root.service --now
sudo updateHyperionUser -u root
after i type sudo reboot i have this
Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!
