LOOP capturing devices purchased from Amazon or Ali Express >> how to set up in Hyperion.NG? problem of re-apearing all the time in remote section/drivers, Only Raspi NOT Windows pc

didism2 · 5. August 2021

Hello people

I had done all the procedures mentioned here, including I installed Hyperbian, and I redid all the procedures and it didn't work.

Then I found out that the problem is really on my capture card, just because it doesn't detect the HDMI Input signal.

So I just unplug the HDMI Input and plug it in again, and it works normally.

So, I believe that changing the capture card everything works...

I'm about to use one of these 3 options:

1 - Rullz USB 3.0 Loop U3

https://pt.aliexpress.com/item…4c04541539c0399019a60778a

2 - ?????

https://pt.aliexpress.com/item….8148356.3.335b6716MTQtgD

3 - EzCap 301 Pro:

https://pt.aliexpress.com/item…-4c57-af23-a8ba59eede4c-9

Thinking I'm going to use multiple 4K devices, I'm also thinking about making a purchase of a raspberry pi4 4GB, but I'm going to keep using the same Adalight.

What do you advise me?

Ambientheater77 · 6. August 2021

Zitat von didism2

1 - Rullz USB 3.0 Loop U3

i think that one most users have and works out of the box .

Zitat von didism2

Thinking I'm going to use multiple 4K devices, I'm also thinking about making a purchase of a raspberry pi4 4GB,

check if the Raspi is capable to run Hyperion on the hardware, some Raspi 4 types have hardware problems to steer leds.

you can find it here on the forum.

thommy86 · 20. Februar 2022

I cannot get a stable working loop. At first I was using the loop with the second output of my AVR. It makes sense that this was not stable, so after a while I wanted to fiddle with my setup again and I bought a Xolorspace splitter.

So my setup is kinda like other people around here:

Nvidia shield => AVR => Xolorspace => the 2 outputs, TV and the Rullz 4k loop

I noticed that when I power the Pi (and loop) with a usb port build in a powerbrick, the behavior is way worse. Are the issue power related? Is my powersupply not good enough?

I power the leds (and wemos) with a meanwell 75w. Should I add the Pi to this powersupply?

Every comment on this topic I tried. Any tips?

Code

2022-02-20T21:34:52.950Z [ WEBSOCKET] (DEBUG) (JsonAPI.cpp:1099:handleLoggingCommand()) log streaming deactivated for client  ::ffff:192.168.178.186
2022-02-20T21:34:52.951Z [ WEBSOCKET] (DEBUG) (JsonAPI.cpp:1090:handleLoggingCommand()) log streaming activated for client ::ffff:192.168.178.186
2022-02-20T21:35:16.501Z [ V4L2] (INFO) Set flipmode to NO_CHANGE
2022-02-20T21:35:16.501Z [ V4L2] (INFO) Cropping image: width=720 height=576; crop: left=13 right=13 top=10 bottom=10 
2022-02-20T21:35:16.596Z [ V4L2] (DEBUG) (V4L2Grabber.cpp:151:init()) Set device (path) to: UVC Camera (534d:2109): USB Vid (/dev/video0)
2022-02-20T21:35:16.597Z [ V4L2] (DEBUG) (V4L2Grabber.cpp:488:init_device()) Set device input to: Camera 1
2022-02-20T21:35:16.598Z [ V4L2] (DEBUG) (V4L2Grabber.cpp:614:init_device()) Set resolution to width=720 height=576
2022-02-20T21:35:16.599Z [ V4L2] (DEBUG) (V4L2Grabber.cpp:631:init_device()) Set framerate to 20 fps
2022-02-20T21:35:16.599Z [ V4L2] (DEBUG) (V4L2Grabber.cpp:707:init_device()) Pixel format=YUYV
2022-02-20T21:35:16.604Z [ V4L2] (ERROR) Throws error nr: VIDIOC_STREAMON error code 5, Input/output error
2022-02-20T21:35:16.604Z [ V4L2] (INFO) Started
2022-02-20T21:35:16.605Z [ V4L2] (ERROR) Throws error nr: VIDIOC_DQBUF error code 22, Invalid argument
2022-02-20T21:35:16.608Z [ V4L2] (INFO) Stopped
2022-02-20T21:35:22.677Z [ WEBSOCKET] (DEBUG) (JsonAPI.cpp:1099:handleLoggingCommand()) log streaming deactivated for client  ::ffff:192.168.178.186
2022-02-20T21:35:22.680Z [ WEBSOCKET] (DEBUG) (JsonAPI.cpp:1090:handleLoggingCommand()) log streaming activated for client ::ffff:192.168.178.186

Alles anzeigen

LOOP capturing devices purchased from Amazon or Ali Express >> how to set up in Hyperion.NG? problem of re-apearing all the time in remote section/drivers, Only Raspi NOT Windows pc

Jetzt mitmachen!

Tags