Hallo zusammen,
ich habe hier das Problem das mir die LEDs immer ausgeschaltet werden.
Mit der Fernbedienung in Hyperion NG muss ich es dann wieder einschalten.
dauert dann keine 10 min da ist es wieder aus.
hier mal ein Auszug vom Log. Vielleicht sieht jemand etwas was ich nicht sehe?
Danke
Code
2021-05-26T12:01:30.752Z [hyperiond V4L2:/DEV/VIDEO0] (INFO) Started 2021-05-26T12:01:30.753Z [hyperiond V4L2:/dev/video0] (DEBUG) (GrabberWrapper.cpp:48:start()) Grabber start() 2021-05-26T12:01:30.848Z [hyperiond HYPERION] (DEBUG) (PriorityMuxer.cpp:251:setInputImage()) Priority 240 is now active 2021-05-26T12:01:30.849Z [hyperiond HYPERION] (DEBUG) (PriorityMuxer.cpp:351:setCurrentTime()) Set visible priority to 240 2021-05-26T12:01:30.852Z [hyperiond HYPERION] (DEBUG) (Hyperion.cpp:559:handlePriorityChangedLedDevice()) priority[240], previousPriority[255] 2021-05-26T12:01:30.853Z [hyperiond HYPERION] (DEBUG) (Hyperion.cpp:569:handlePriorityChangedLedDevice()) new source available -> switch LED-Device on 2021-05-26T12:01:42.835Z [hyperiond WEBSOCKET] (DEBUG) (JsonAPI.cpp:1054:handleLoggingCommand()) log streaming activated for client ::ffff:172.16.10.57 2021-05-26T12:01:42.897Z [hyperiond WEBSOCKET] (DEBUG) (JsonAPI.cpp:1063:handleLoggingCommand()) log streaming deactivated for client ::ffff:172.16.10.57 2021-05-26T12:04:21.175Z [hyperiond WEBSOCKET] (DEBUG) (WebSocketClient.cpp:204:sendClose()) send close: 1000 2021-05-26T12:04:21.574Z [hyperiond WEBSOCKET] (DEBUG) (WebSocketClient.cpp:30:WebSocketClient()) New connection from ::ffff:172.16.10.57 2021-05-26T12:04:21.576Z [hyperiond WEBSOCKET] (DEBUG) (JsonAPI.cpp:81:handleInstanceSwitch()) Client '::ffff:172.16.10.57' switch to Hyperion instance 0 2021-05-26T12:06:35.800Z [hyperiond V4L2:/DEV/VIDEO0] (ERROR) Throws error nr: VIDIOC_QBUF error code 19, No such device 2021-05-26T12:06:35.801Z [hyperiond V4L2:/DEV/VIDEO0] (ERROR) Throws error nr: VIDIOC_DQBUF error code 19, No such device 2021-05-26T12:06:35.801Z [hyperiond V4L2:/DEV/VIDEO0] (ERROR) VIDIOC_STREAMOFF error code 19, No such device 2021-05-26T12:06:35.805Z [hyperiond V4L2:/DEV/VIDEO0] (INFO) Stopped 2021-05-26T12:06:36.748Z [hyperiond HYPERION] (DEBUG) (PriorityMuxer.cpp:251:setInputImage()) Priority 240 is now inactive 2021-05-26T12:06:36.748Z [hyperiond HYPERION] (DEBUG) (PriorityMuxer.cpp:351:setCurrentTime()) Set visible priority to 255 2021-05-26T12:06:36.749Z [hyperiond HYPERION] (DEBUG) (Hyperion.cpp:559:handlePriorityChangedLedDevice()) priority[255], previousPriority[240] 2021-05-26T12:06:36.749Z [hyperiond HYPERION] (DEBUG) (Hyperion.cpp:562:handlePriorityChangedLedDevice()) No source left -> switch LED-Device off 2021-05-26T12:08:43.487Z [hyperiond HYPERION] (DEBUG) (PriorityMuxer.cpp:270:clearInput()) Removed source priority 240 2021-05-26T12:08:43.488Z [hyperiond COMPONENTREG] (DEBUG) (ComponentRegister.cpp:36:setNewComponentState()) V4L capture device: disabled 2021-05-26T12:08:43.489Z [hyperiond V4L2:/dev/video0] (DEBUG) (GrabberWrapper.cpp:58:stop()) Grabber stop() 2021-05-26T12:08:44.318Z [hyperiond HYPERION] (DEBUG) (PriorityMuxer.cpp:161:registerInput()) Register new input 'System/V4L' with priority 240 as inactive 2021-05-26T12:08:44.319Z [hyperiond COMPONENTREG] (DEBUG) (ComponentRegister.cpp:36:setNewComponentState()) V4L capture device: enabled 2021-05-26T12:08:44.320Z [hyperiond V4L2:/DEV/VIDEO0] (INFO) configured v4l device: /dev/video0 2021-05-26T12:08:44.323Z [hyperiond V4L2:/DEV/VIDEO0] (DEBUG) (V4L2Grabber.cpp:582:init_device()) Set device input to: Composite 2021-05-26T12:08:44.335Z [hyperiond V4L2:/DEV/VIDEO0] (DEBUG) (V4L2Grabber.cpp:601:init_device()) Video standard=PAL 2021-05-26T12:08:44.336Z [hyperiond V4L2:/DEV/VIDEO0] (DEBUG) (V4L2Grabber.cpp:696:init_device()) Set resolution to width=720 height=576 2021-05-26T12:08:44.336Z [hyperiond V4L2:/DEV/VIDEO0] (DEBUG) (V4L2Grabber.cpp:735:init_device()) Pixel format=YUYV 2021-05-26T12:08:44.387Z [hyperiond V4L2:/DEV/VIDEO0] (INFO) Started 2021-05-26T12:08:44.387Z [hyperiond V4L2:/dev/video0] (DEBUG) (GrabberWrapper.cpp:48:start()) Grabber start() 2021-05-26T12:08:44.497Z [hyperiond HYPERION] (DEBUG) (PriorityMuxer.cpp:251:setInputImage()) Priority 240 is now active 2021-05-26T12:08:44.497Z [hyperiond HYPERION] (DEBUG) (PriorityMuxer.cpp:351:setCurrentTime()) Set visible priority to 240 2021-05-26T12:08:44.500Z [hyperiond HYPERION] (DEBUG) (Hyperion.cpp:559:handlePriorityChangedLedDevice()) priority[240], previousPriority[255] 2021-05-26T12:08:44.501Z [hyperiond HYPERION] (DEBUG) (Hyperion.cpp:569:handlePriorityChangedLedDevice()) new source available -> switch LED-Device on 2021-05-26T12:08:50.806Z [hyperiond WEBSOCKET] (DEBUG) (JsonAPI.cpp:1054:handleLoggingCommand()) log streaming activated for client ::ffff:172.16.10.57