Beiträge von jman203

I may have figured out the issue on another forum. Since the LEDs and pi are not connected to the same power supply, they don't have a common ground. This is likely causing the random blinking of the lights and not matching what Hyperion software is showing. I'll try it out tonight and see if that fixes the issue.

You are correct that I'm using the 256 WS2812B's . I'm using a 5V 10A barrel jack style power supply that is only powering the LED's. I used a short (4" long) 26 gauge jumper for the signal wire. The barrel connector is connected directly to the end of the LED strip.

Below is the debug log:

2021-04-05T01:54:05.734Z [hyperiond LEDDEVICE] (INFO) Start LedDevice 'ws281x'.

2021-04-05T01:54:05.734Z [hyperiond COMPONENTREG] (DEBUG) (ComponentRegister.cpp:36:setNewComponentState()) LED device: disabled

2021-04-05T01:54:05.735Z [hyperiond LEDDEVICE] (DEBUG) (LedDevice.cpp:148:init()) deviceConfig: [{"colorOrder":"rgb","currentLedCount":190,"dma":5,"gpio":18,"hardwareLedCount":190,"invert":false,"latchTime":0,"leds":256,"pwmchannel":0,"rewriteTime":1000,"rgbw":false,"type":"ws281x","whiteAlgorithm":"subtract_minimum"}]

2021-04-05T01:54:05.735Z [hyperiond LEDDEVICE] (DEBUG) (LedDevice.cpp:407:setLatchTime()) LatchTime updated to 0ms

2021-04-05T01:54:05.735Z [hyperiond LEDDEVICE] (DEBUG) (LedDevice.cpp:428:setRewriteTime()) Refresh interval = 1000ms

2021-04-05T01:54:05.735Z [hyperiond LEDDEVICE] (DEBUG) (LedDevice.cpp:434:setRewriteTime()) RewriteTime updated to 1000ms

2021-04-05T01:54:05.735Z [hyperiond LEDDEVICE] (DEBUG) (LedDeviceWS281x.cpp:59:init()) ws281x strip type : 1050624

2021-04-05T01:54:05.737Z [hyperiond COMPONENTREG] (DEBUG) (ComponentRegister.cpp:36:setNewComponentState()) LED device: enabled

2021-04-05T01:54:08.035Z [hyperiond DISPMANXGRABBER] (ERROR) Previous line repeats 200 times2021-04-05T02:56:46.935Z [hyperiond DISPMANXGRABBER] (ERROR) Previous line repeats 200 times

2021-04-05T02:56:59.296Z [hyperiond WEBSOCKET] (DEBUG) (JsonAPI.cpp:1063:handleLoggingCommand()) Previous line repeats 1 times

2021-04-05T02:56:59.296Z [hyperiond WEBSOCKET] (DEBUG) (JsonAPI.cpp:1054:handleLoggingCommand()) log streaming activated for client ::ffff:192.168.1.67

2021-04-05T02:56:59.296Z [hyperiond WEBSOCKET] (DEBUG) (JsonAPI.cpp:1054:handleLoggingCommand()) log streaming activated for client ::ffff:192.168.1.67

I'm following a Youtube tutorial to put LED's around my television and match the television signal. I have followed it to setup Hyperion on a Raspberry Pi 4, and the video capture card is receiving the correct signal. I can see the TV picture on the LED visualization. No matter what color is shown in Hyperion, the LED's are flashing a variety of colors quickly. I purchased the same LED's and followed the same controller configuration. When I turn off the video capture and set Hyperion to a constant color, it still flashes the same variety of colors. Any suggestions to trouble shoot the issue?