Okay... also ich hab jetzt noch etwas rumprobiert (auch mit dem eingepackten Kabel) und es funtkioniert immer noch nicht. wenn ich auf den Steuerkanal der LEDs von Hand eine Spannung anlege funktionieren alle (also an den Lötstellen kann´s nicht liegen. Das muss irgendwas mit dem Rasperry zu tun haben.
Beiträge von dagloadone
-
-
andere SD karten hab ich tatsächlich auch schon ausprobiert... aber hat auch nix gebracht...
Wenn das ganze wieder funktioniert dann kleb ich die von mir aus auch mit Sekundenkleber rein, dass die keiner mehr nehmen kann xD
-
Ja ich weiß die sehen echt mieß aus aber mich wundert‘s halt dass es ja vor dem SD Karten reset funktioniert hat... und seitdem hab ich nichts an meiner Verkabelung geändert... also muss es ja eigentlich was Software seitiges sein oder? Die Lötstellen sehen zwar mieß aus aber ich hab sie alle mit einem Messgerät überprüft und die funktionieren auch gut... das mit dem Abgeschirmten Kabel werd ich morgen mal versuchen... Danke dir
-
pwm hab ich auch versucht aber funktioniert auch nicht
-
Auf SPI... Also auf sk6812 spi
-
Ja natürlich... gerne
-
okay it still doesn´t work... just the first led is lighting up green
-
yea i got two seperate supplies... i´m gonna try that
-
i know my soldering looks like shit but it works (i tested all the connections)
the red wire from the Rasperry pi goes directly into the LED strip (the middle connector)
those orange wago things are just to get Power into every corner of the LED strip and the Power supply ist also connected to those... i also measure 5.12 Volts on the LED strip.
i disconnected the Level switcher as it worked before without it.
-
i´m so frustrated... i tried everything and it still doesn´t work... i even connected the Level switcher again, tried different LED controllers, different Pins, checked all Connections on the hardware but i can´t get it to work... the irritating thing is that before the SD-card reset everything worked completely fine
-
and yes led device is on
-
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
dtparam=spi=on# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=off[pi4]
# Enable DRM VC4 V3D driver on top of the dispmanx display stack
dtoverlay=vc4-fkms-v3d
max_framebuffers=2[all]
#dtoverlay=vc4-fkms-v3d -
i imported them manually
-
but i´m curious why it´s not working now... i didn´t change the Wires and i used my old settings that worked before
-
just don´t ask xD
my brother took it and thought it wasn´t important so he formated it to use it for his 3D printer
-
i just did turn white off because i got the best color Results
but i got another Issue... i accidentially formated my SD card and had to install hyperbian again... i used my settings from before and now it doesn´t work anymore. Just the first LED is lighting up but it´s also not doing what it should do.
-
-
Okay so i found out that the issue was the Level switcher... i connected the LEDs directly to the raspi and now it works like a charm
-
Okay so i habe tried both... the other spi Controller doesnt work at all... it‘s just flickering no matter what baudrate i choose... the PWM also doesn‘t work at all... the LEDs just stay black the whole time
-
hm okay... thanks anyways