Beiträge von didism2

    Hello people


    I had done all the procedures mentioned here, including I installed Hyperbian, and I redid all the procedures and it didn't work.


    Then I found out that the problem is really on my capture card, just because it doesn't detect the HDMI Input signal.


    So I just unplug the HDMI Input and plug it in again, and it works normally.


    So, I believe that changing the capture card everything works...


    I'm about to use one of these 3 options:


    1 - Rullz USB 3.0 Loop U3

    https://pt.aliexpress.com/item…4c04541539c0399019a60778a


    2 - ?????

    https://pt.aliexpress.com/item….8148356.3.335b6716MTQtgD


    3 - EzCap 301 Pro:

    https://pt.aliexpress.com/item…-4c57-af23-a8ba59eede4c-9


    Thinking I'm going to use multiple 4K devices, I'm also thinking about making a purchase of a raspberry pi4 4GB, but I'm going to keep using the same Adalight.


    What do you advise me?

    Hello, how is everything ?


    Thank you very much for your feedback.



    I had already tested these options, but I just sudo to update && sudo to update -y && sudo to install hdmi2usb-mode-switch, I sudo restarted and that was it, but it still didn't work.


    But I didn't exist dispelled certain firmwares below:

    hdmi2usb-fx2-firmware - FX2 firmware for hdmi2usb board development
    fxload - Firmware download to EZ-USB devices


    1 - Sorry for the question, and for my ignorance and lack of information, but what would be the command to run one of these firmwares?

    2 - Also, if I come to exchange the installed RaspiOS Buster and the last version of Hyperion.NG installed, for Hyperbian, would I have to do this procedure of running a firmware too?




    I think the picture in post # 36 shows an HDCP problem.

    It's strange to be a HDCP problem, because as I said before, it works fine, then when it restarts, it stops working .... then I have to make several adjustments and restart about 5x, then it starts working again.

    Not to mention that a capture card shows that it's HDCP 2.2


    But if that is really the problem, what would be the capture card with HDCP 2.2 EDID available on Aliexpress, Bangood or Gearbest, (or one that delivers here in BR) you indicators for my scenario?

    Hello everybody, How are you?


    I hope so.


    I'm from Brazil (Brazil), and I don't speak English, forgive me.


    I have several 4K devices here, such as Playstation 5, Xbox Series X, FireTV 4K, Mi Box TV, Nintendo Swith, Xbox 360, Cable TV Receiver (Claro NET).


    I have a Raspberry PI 3B, with a 32GB MicroSD card with RaspiOS Buster installed and the latest version of Hyperion.NG installed "Hyperion 2.0.0-alpha.10" Linux-armv7l ....


    Use the following 3.0 capture card:

    https://pt.aliexpress.com/item…042311.0.0.2742b90abtjVEO


    My LEDs are these here:

    https://pt.aliexpress.com/item…042311.0.0.2742b90ajvzAER


    It is a Kit 4M 60 LEDS per meter - EU PLUG.


    I'm using this kit installed as Adalight on the USB port in Hyperion.NG, and the LEDs work perfectly.


    I'm using the following connection:


    A - 4K devices connected via HDMI on the capture card (HDMI input)


    B - HDMI output from the Capture card plugged in without the TV's HDMI.


    C - USB3.0 port of the capture card plugged into Raspi 3B (I know the USB output of RASP is only 2.0, but I've seen it in several tutorials on the internet working smoothly)


    My problem is getting the image on the capture card, where it sometimes works normally, when I restart I see this same screen:


    adliberum-fear-the-white-noise.mp4.jpg


    I've already made the settings mentioned above:



    I've also done the configuration in /boot/config.txt:

    #uncomment to overclock the arm. 700 MHz is the default.

    arm_freq=900

    force_turbo=1


    max_usb_current=1

    max_usb_current=1


    It works, but the same way as before, when restarting, it stops working.


    I didn't want to buy a Raspi 4, because here in Brazil it costs almost 1 minimum wage here.


    1 - Does anyone have any other suggestions?


    2 - And if, as a last option, I choose to buy an RPI4 4GB, can I use the same materials I already have? (Capture board and LED Kit)?


    3 - I have another scenario, which has the same equipment, with the same devices, and also an RPi3 B, but the TV is 1080p, could you recommend a capture card that works without problems in this scenario?


    Thank you very much