Ended up testing a new string of LEDs and they worked so apparently the existing string died which is strange. The PI and LEDs are on the same power supply and although I have had a PI die, I have never had a strip die.
Beiträge von jsmonty
-
-
At a loss at what to test next, any help would be appreciated!
Raspi Zero W has been running for a while with no changes, but LED stopped responding. I've tested by jumping power to TX and LEDs light up so I assume the strip is fine. Replaced with new pi Zero with no change, rebuilt image and restored with backup config with no change. Logs attached.
-
Unplugged and replugged everything back in and so far it's working. Strange that all I did was kill power and swap SD card in the Pi but happy its working!
-
After running HyperBian on 2.0.0-alpha9 successfully I finally upgraded, as i've started using HomeAssistant integration and noticed some improvements in current version (even though I wasn't having issues at the time). I went back through setup guide, used prior config to mirror settings and its up and running. The issue I am having is the USB capture is failing after running for a few seconds. Log output below. Nothing physical has changed with my setup, i'm not sure if I missed a setting somewhere, or something has changed in the newer version.
Code
Alles anzeigen2022-01-27T15:43:38.171Z [ HYPERION] (DEBUG) (PriorityMuxer.cpp:271:setInputImage()) Priority 100 is now inactive 2022-01-27T15:43:38.172Z [ HYPERION] (DEBUG) (PriorityMuxer.cpp:374:setCurrentTime()) Set visible priority to 255 2022-01-27T15:43:38.172Z [ HYPERION] (DEBUG) (Hyperion.cpp:571:handleSourceAvailability()) priority[255], previousPriority[100] 2022-01-27T15:43:38.173Z [ HYPERION] (DEBUG) (Hyperion.cpp:574:handleSourceAvailability()) No source left -> Pause output processing and switch LED-Device off 2022-01-27T15:53:34.143Z [ WEBSOCKET] (DEBUG) (JsonAPI.cpp:1099:handleLoggingCommand()) log streaming deactivated for client ::ffff:192.168.38.82 2022-01-27T15:53:34.161Z [ WEBSOCKET] (DEBUG) (JsonAPI.cpp:1090:handleLoggingCommand()) log streaming activated for client ::ffff:192.168.38.82 2022-01-27T15:58:38.614Z [ WEBSOCKET] (DEBUG) (JsonAPI.cpp:1099:handleLoggingCommand()) log streaming deactivated for client ::ffff:192.168.38.82 2022-01-27T15:58:38.624Z [ WEBSOCKET] (DEBUG) (JsonAPI.cpp:1090:handleLoggingCommand()) log streaming activated for client ::ffff:192.168.38.82 2022-01-27T15:58:50.538Z [ HYPERION] (DEBUG) (PriorityMuxer.cpp:292:clearInput()) Removed source priority 100 2022-01-27T15:58:50.545Z [ COMPONENTREG] (DEBUG) (ComponentRegister.cpp:41:setNewComponentState()) V4L capture device: disabled 2022-01-27T15:58:50.557Z [ V4L2] (DEBUG) (GrabberWrapper.cpp:76:stop()) Grabber stop() 2022-01-27T15:58:52.600Z [ HYPERION] (DEBUG) (PriorityMuxer.cpp:165:registerInput()) Register new input 'System/V4L' with priority 100 as inactive 2022-01-27T15:58:52.607Z [ COMPONENTREG] (DEBUG) (ComponentRegister.cpp:41:setNewComponentState()) V4L capture device: enabled 2022-01-27T15:58:52.909Z [ V4L2] (DEBUG) (V4L2Grabber.cpp:151:init()) Set device (path) to: UVC Camera (534d:2109): USB Vid (/dev/video0) 2022-01-27T15:58:52.915Z [ V4L2] (DEBUG) (V4L2Grabber.cpp:488:init_device()) Set device input to: Camera 1 2022-01-27T15:58:52.921Z [ V4L2] (DEBUG) (V4L2Grabber.cpp:614:init_device()) Set resolution to width=640 height=480 2022-01-27T15:58:52.929Z [ V4L2] (DEBUG) (V4L2Grabber.cpp:631:init_device()) Set framerate to 5 fps 2022-01-27T15:58:52.934Z [ V4L2] (DEBUG) (V4L2Grabber.cpp:707:init_device()) Pixel format=YUYV 2022-01-27T15:58:52.946Z [ V4L2] (INFO) Started 2022-01-27T15:58:52.951Z [ V4L2] (DEBUG) (GrabberWrapper.cpp:62:start()) Grabber start() 2022-01-27T15:58:53.555Z [ HYPERION] (DEBUG) (PriorityMuxer.cpp:271:setInputImage()) Priority 100 is now active 2022-01-27T15:58:53.565Z [ HYPERION] (DEBUG) (PriorityMuxer.cpp:374:setCurrentTime()) Set visible priority to 100 2022-01-27T15:58:53.572Z [ HYPERION] (DEBUG) (Hyperion.cpp:571:handleSourceAvailability()) priority[100], previousPriority[255] 2022-01-27T15:58:53.576Z [ HYPERION] (DEBUG) (Hyperion.cpp:582:handleSourceAvailability()) new source available -> Resume output processing and switch LED-Device on 2022-01-27T15:58:58.982Z [ WEBSOCKET] (DEBUG) (JsonAPI.cpp:1099:handleLoggingCommand()) log streaming deactivated for client ::ffff:192.168.38.82 2022-01-27T15:58:58.997Z [ WEBSOCKET] (DEBUG) (JsonAPI.cpp:1090:handleLoggingCommand()) log streaming activated for client ::ffff:192.168.38.82 2022-01-27T16:01:29.507Z [ V4L2] (ERROR) Throws error nr: VIDIOC_DQBUF error code 19, No such device 2022-01-27T16:01:29.517Z [ V4L2] (ERROR) VIDIOC_STREAMOFF error code 19, No such device 2022-01-27T16:01:29.547Z [ V4L2] (INFO) Stopped 2022-01-27T16:01:30.265Z [ HYPERION] (DEBUG) (PriorityMuxer.cpp:271:setInputImage()) Priority 100 is now inactive 2022-01-27T16:01:30.271Z [ HYPERION] (DEBUG) (PriorityMuxer.cpp:374:setCurrentTime()) Set visible priority to 255 2022-01-27T16:01:30.276Z [ HYPERION] (DEBUG) (Hyperion.cpp:571:handleSourceAvailability()) priority[255], previousPriority[100] 2022-01-27T16:01:30.281Z [ HYPERION] (DEBUG) (Hyperion.cpp:574:handleSourceAvailability()) No source left -> Pause output processing and switch LED-Device off 2022-01-27T16:03:09.408Z [ WEBSOCKET] (DEBUG) (JsonAPI.cpp:1099:handleLoggingCommand()) log streaming deactivated for client ::ffff:192.168.38.82 2022-01-27T16:03:09.423Z [ WEBSOCKET] (DEBUG) (JsonAPI.cpp:1090:handleLoggingCommand()) log streaming activated for client ::ffff:192.168.38.82
USB capture settings seem to discover a device, vs in the old version it was just "automatic."