Finally my setup is working but not al my leds burn ? Some leds burn a little bit I dont know why Im using 234 ws2812b leds on a 5v 10a supply.
how did you get them going, im having same issue
Finally my setup is working but not al my leds burn ? Some leds burn a little bit I dont know why Im using 234 ws2812b leds on a 5v 10a supply.
how did you get them going, im having same issue
Raspbian
Hyperion
Raspberry Pi 1 model b
WS2812b Leds
Hyperion shows everything passing, Raspbian startup shows Hyperion successful. However, the lights don't budge.
I'll try again tonight. But yeah that was usually the error, but I would check and it was named properly. Below is most recent test I had on different build, but same issue.
Code:
SSH Traffic:
ssh connected
ssh out: cd /tmp && wget -nv -N https://raw.github.com/hyperion-project/hyperion/master/bin/install_hyperion.sh && chmod +x install_hyperion.sh && sudo sh ./install_hyperion.sh HyperConInstall ; rm install_hyperion.sh
ssh out: Last-modified header missing -- time-stamps turned off.
ssh out: 2017-09-19 22:39:01 URL:https://raw.githubusercontent.com/hyperion-project/hyperion/master/bin/install_hyperion.sh [14552/14552] -> "install_hyperion.sh" [1]
ssh in: *******************************************************************************
ssh in: This script will install/update Hyperion Ambient Light
ssh in: Created by brindosch - hyperion-project.org - the official Hyperion source.
ssh in: *******************************************************************************
ssh in: ---> Stop Hyperion, if necessary
ssh in: ---> Install/Update Hyperion dependencies (This may take a while)
ssh out: debconf: unable to initialize frontend: Dialog
ssh out: debconf: (Dialog frontend will not work on a dumb terminal, an emacs shell buffer, or without a controlling terminal.)
ssh out: debconf: falling back to frontend: Readline
ssh out: debconf: unable to initialize frontend: Readline
ssh out: debconf: (Can't locate Term/ReadLine.pm in @INC (you may need to install the Term::ReadLine module) (@INC contains: /etc/perl /usr/local/lib/arm-linux-gnueabihf/perl/5.20.2 /usr/local/share/perl/5.20.2 /usr/lib/arm-linux-gnueabihf/perl5/5.20 /usr/share/perl5 /usr/lib/arm-linux-gnueabihf/perl/5.20 /usr/share/perl/5.20 /usr/local/lib/site_perl .) at /usr/share/perl5/Debconf/FrontEnd/Readline.pm line 7, <> line 22.)
ssh out: debconf: falling back to frontend: Teletype
ssh out: dpkg-preconfigure: unable to re-open stdin:
ssh in: Selecting previously unselected package fontconfig.
ssh in: (Reading database ...
ssh in: (Reading database ... 5%
ssh in: (Reading database ... 10%
ssh in: (Reading database ... 15%
ssh in: (Reading database ... 20%
ssh in: (Reading database ... 25%
ssh in: (Reading database ... 30%
ssh in: (Reading database ... 35%
ssh in: (Reading database ... 40%
ssh in: (Reading database ... 45%
ssh in: (Reading database ... 50%
ssh in: (Reading database ... 55%
ssh in: (Reading database ... 60%
ssh in: (Reading database ... 65%
ssh in: (Reading database ... 70%
ssh in: (Reading database ... 75%
ssh in: (Reading database ... 80%
ssh in: (Reading database ... 85%
ssh in: (Reading database ... 90%
ssh in: (Reading database ... 95%
ssh in: (Reading database ... 100%
ssh in: (Reading database ... 23148 files and directories currently installed.)
ssh in: Preparing to unpack .../fontconfig_2.11.0-6.3+deb8u1_armhf.deb ...
ssh in: Unpacking fontconfig (2.11.0-6.3+deb8u1) ...
ssh in: Selecting previously unselected package libxau6:armhf.
ssh in: Preparing to unpack .../libxau6_1%3a1.0.8-1_armhf.deb ...
ssh in: Unpacking libxau6:armhf (1:1.0.8-1) ...
ssh in: Selecting previously unselected package x11-common.
ssh in: Preparing to unpack .../x11-common_1%3a7.7+7_all.deb ...
ssh in: Unpacking x11-common (1:7.7+7) ...
ssh in: Selecting previously unselected package libice6:armhf.
ssh in: Preparing to unpack .../libice6_2%3a1.0.9-1_armhf.deb ...
ssh in: Unpacking libice6:armhf (2:1.0.9-1) ...
ssh in: Selecting previously unselected package libsm6:armhf.
ssh in: Preparing to unpack .../libsm6_2%3a1.2.2-1_armhf.deb ...
ssh in: Unpacking libsm6:armhf (2:1.2.2-1) ...
ssh in: Selecting previously unselected package libxdmcp6:armhf.
ssh in: Preparing to unpack .../libxdmcp6_1%3a1.1.1-1_armhf.deb ...
ssh in: Unpacking libxdmcp6:armhf (1:1.1.1-1) ...
ssh in: Selecting previously unselected package libxcb1:armhf.
ssh in: Preparing to unpack .../libxcb1_1.10-3_armhf.deb ...
ssh in: Unpacking libxcb1:armhf (1.10-3) ...
ssh in: Selecting previously unselected package libx11-data.
ssh in: Preparing to unpack .../libx11-data_2%3a1.6.2-3_all.deb ...
ssh in: Unpacking libx11-data (2:1.6.2-3) ...
ssh in: Selecting previously unselected package libx11-6:armhf.
ssh in: Preparing to unpack .../libx11-6_2%3a1.6.2-3_armhf.deb ...
ssh in: Unpacking libx11-6:armhf (2:1.6.2-3) ...
ssh in: Selecting previously unselected package libxt6:armhf.
ssh in: Preparing to unpack .../libxt6_1%3a1.1.4-1_armhf.deb ...
ssh in: Unpacking libxt6:armhf (1:1.1.4-1) ...
ssh in: Selecting previously unselected package libaudio2:armhf.
ssh in: Preparing to unpack .../libaudio2_1.9.4-3_armhf.deb ...
ssh in: Unpacking libaudio2:armhf (1.9.4-3) ...
ssh in: Selecting previously unselected package libjpeg8:armhf.
ssh in: Preparing to unpack .../libjpeg8_8d1-2_armhf.deb ...
ssh in: Unpacking libjpeg8:armhf (8d1-2) ...
ssh in: Selecting previously unselected package libmng1:armhf.
ssh in: Preparing to unpack .../libmng1_1.0.10+dfsg-3.1_armhf.deb ...
ssh in: Unpacking libmng1:armhf (1.0.10+dfsg-3.1) ...
ssh in: Selecting previously unselected package qtcore4-l10n.
ssh in: Preparing to unpack .../qtcore4-l10n_4%3a4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1_all.deb ...
ssh in: Unpacking qtcore4-l10n (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Selecting previously unselected package libqtcore4:armhf.
ssh in: Preparing to unpack .../libqtcore4_4%3a4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1_armhf.deb ...
ssh in: Unpacking libqtcore4:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Selecting previously unselected package libqt4-xml:armhf.
ssh in: Preparing to unpack .../libqt4-xml_4%3a4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1_armhf.deb ...
ssh in: Unpacking libqt4-xml:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Selecting previously unselected package libqtdbus4:armhf.
ssh in: Preparing to unpack .../libqtdbus4_4%3a4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1_armhf.deb ...
ssh in: Unpacking libqtdbus4:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Selecting previously unselected package libqt4-network:armhf.
ssh in: Preparing to unpack .../libqt4-network_4%3a4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1_armhf.deb ...
ssh in: Unpacking libqt4-network:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Selecting previously unselected package libxext6:armhf.
ssh in: Preparing to unpack .../libxext6_2%3a1.3.3-1_armhf.deb ...
ssh in: Unpacking libxext6:armhf (2:1.3.3-1) ...
ssh in: Selecting previously unselected package libxrender1:armhf.
ssh in: Preparing to unpack .../libxrender1_1%3a0.9.8-1_armhf.deb ...
ssh in: Unpacking libxrender1:armhf (1:0.9.8-1) ...
ssh in: Selecting previously unselected package libqtgui4:armhf.
ssh in: Preparing to unpack .../libqtgui4_4%3a4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1_armhf.deb ...
ssh in: Unpacking libqtgui4:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Selecting previously unselected package libusb-1.0-0:armhf.
ssh in: Preparing to unpack .../libusb-1.0-0_2%3a1.0.19-1_armhf.deb ...
ssh in: Unpacking libusb-1.0-0:armhf (2:1.0.19-1) ...
ssh in: Processing triggers for systemd (215-17+deb8u7) ...
ssh in: Setting up fontconfig (2.11.0-6.3+deb8u1) ...
ssh in: Regenerating fonts cache... done.
ssh in: Setting up libxau6:armhf (1:1.0.8-1) ...
ssh in: Setting up x11-common (1:7.7+7) ...
ssh in: debconf: unable to initialize frontend: Dialog
ssh in: debconf: (Dialog frontend will not work on a dumb terminal, an emacs shell buffer, or without a controlling terminal.)
ssh in: debconf: falling back to frontend: Readline
ssh in: debconf: unable to initialize frontend: Readline
ssh in: debconf: (Can't locate Term/ReadLine.pm in @INC (you may need to install the Term::ReadLine module) (@INC contains: /etc/perl /usr/local/lib/arm-linux-gnueabihf/perl/5.20.2 /usr/local/share/perl/5.20.2 /usr/lib/arm-linux-gnueabihf/perl5/5.20 /usr/share/perl5 /usr/lib/arm-linux-gnueabihf/perl/5.20 /usr/share/perl/5.20 /usr/local/lib/site_perl .) at /usr/share/perl5/Debconf/FrontEnd/Readline.pm line 7.)
ssh in: debconf: falling back to frontend: Teletype
ssh in: /var/lib/dpkg/info/x11-common.postinst: 697: /var/lib/dpkg/info/x11-common.postinst: update-rc.d: not found
ssh in: dpkg: error processing package x11-common (--configure):
ssh in: subprocess installed post-installation script returned error exit status 127
ssh in: dpkg: dependency problems prevent configuration of libice6:armhf:
ssh in: libice6:armhf depends on x11-common; however:
ssh in: Package x11-common is not configured yet.
ssh in: dpkg: error processing package libice6:armhf (--configure):
ssh in: dependency problems - leaving unconfigured
ssh in: dpkg: dependency problems prevent configuration of libsm6:armhf:
ssh in: libsm6:armhf depends on libice6 (>= 1:1.0.0); however:
ssh in: Package libice6:armhf is not configured yet.
ssh in: dpkg: error processing package libsm6:armhf (--configure):
ssh in: dependency problems - leaving unconfigured
ssh in: Setting up libxdmcp6:armhf (1:1.1.1-1) ...
ssh in: Setting up libxcb1:armhf (1.10-3) ...
ssh in: Setting up libx11-data (2:1.6.2-3) ...
ssh in: Setting up libx11-6:armhf (2:1.6.2-3) ...
ssh in: dpkg: dependency problems prevent configuration of libxt6:armhf:
ssh in: libxt6:armhf depends on libice6 (>= 1:1.0.0); however:
ssh in: Package libice6:armhf is not configured yet.
ssh in: libxt6:armhf depends on libsm6; however:
ssh in: Package libsm6:armhf is not configured yet.
ssh in: dpkg: error processing package libxt6:armhf (--configure):
ssh in: dependency problems - leaving unconfigured
ssh in: dpkg: dependency problems prevent configuration of libaudio2:armhf:
ssh in: libaudio2:armhf depends on libxt6; however:
ssh in: Package libxt6:armhf is not configured yet.
ssh in: dpkg: error processing package libaudio2:armhf (--configure):
ssh in: dependency problems - leaving unconfigured
ssh in: Setting up libjpeg8:armhf (8d1-2) ...
ssh in: Setting up libmng1:armhf (1.0.10+dfsg-3.1) ...
ssh in: Setting up qtcore4-l10n (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Setting up libqtcore4:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Setting up libqt4-xml:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Setting up libqtdbus4:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Setting up libqt4-network:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Setting up libxext6:armhf (2:1.3.3-1) ...
ssh in: Setting up libxrender1:armhf (1:0.9.8-1) ...
ssh in: dpkg: dependency problems prevent configuration of libqtgui4:armhf:
ssh in: libqtgui4:armhf depends on libaudio2; however:
ssh in: Package libaudio2:armhf is not configured yet.
ssh in: libqtgui4:armhf depends on libice6 (>= 1:1.0.0); however:
ssh in: Package libice6:armhf is not configured yet.
ssh in: libqtgui4:armhf depends on libsm6; however:
ssh in: Package libsm6:armhf is not configured yet.
ssh in: dpkg: error processing package libqtgui4:armhf (--configure):
ssh in: dependency problems - leaving unconfigured
ssh in: Setting up libusb-1.0-0:armhf (2:1.0.19-1) ...
ssh in: Processing triggers for libc-bin (2.19-18+deb8u10) ...
ssh in: Processing triggers for systemd (215-17+deb8u7) ...
ssh in: Errors were encountered while processing:
ssh in: x11-common
ssh in: libice6:armhf
ssh in: libsm6:armhf
ssh in: libxt6:armhf
ssh in: libaudio2:armhf
ssh in: libqtgui4:armhf
ssh out: E: Sub-process /usr/bin/dpkg returned an error code (1)
ssh in: ---> Raspberry Pi found, but SPI is not set, we write "dtparam=spi=on" to /boot/config.txt
ssh in: ---> Downloading the appropriate Hyperion release
ssh out: 2017-09-19 22:43:12 URL:https://cytranet.dl.sourceforge.net/project/hyperion-project/release/hyperion_rpi3_osmc.tar.gz [1639953/1639953] -> "-" [1]
ssh in: ---> Installing systemd script
ssh in: ---> Modify systemd script for OSMC usage
ssh in: ---> Starting Hyperion
ssh in: *******************************************************************************
ssh in: Hyperion Installation/Update finished!
ssh in: Please download the latest HyperCon version to benefit from new features!
ssh in: To create a config, follow the HyperCon Guide at our Wiki (EN/DE)!
ssh in: Wiki: wiki.hyperion-project.org Webpage: www.hyperion-project.org
ssh in: *******************************************************************************
ssh in: Rebooting now, we added dtparam=spi=on to config.txt
ssh disconnected
ssh connected
ssh out: sudo journalctl -u hyperion.service 2>/dev/null
ssh in: -- Logs begin at Tue 2017-09-19 22:50:37 -01, end at Tue 2017-09-19 22:53:01 -01. --
ssh in: Sep 19 22:50:40 osmc systemd[1]: Starting Hyperion Systemd service...
ssh in: Sep 19 22:50:40 osmc systemd[1]: Started Hyperion Systemd service.
ssh in: Sep 19 22:50:44 osmc hyperiond[244]: Hyperion Ambilight Deamon (244)
ssh in: Sep 19 22:50:44 osmc hyperiond[244]: Version : V1.03.3 (brindosch-2fbbcff/2f01dfa-1495880388
ssh in: Sep 19 22:50:44 osmc hyperiond[244]: Build Time: Jun 3 2017 02:06:37
ssh in: Sep 19 22:50:45 osmc hyperiond[244]: ERROR: No valid config found
ssh in: Sep 19 22:50:45 osmc systemd[1]: hyperion.service: main process exited, code=exited, status=1/FAILURE
ssh in: Sep 19 22:50:45 osmc systemd[1]: Unit hyperion.service entered failed state.
ssh in: Sep 19 22:50:46 osmc systemd[1]: hyperion.service holdoff time over, scheduling restart.
ssh in: Sep 19 22:50:46 osmc systemd[1]: Stopping Hyperion Systemd service...
ssh in: Sep 19 22:50:46 osmc systemd[1]: Starting Hyperion Systemd service...
ssh in: Sep 19 22:50:46 osmc systemd[1]: Started Hyperion Systemd service.
ssh in: Sep 19 22:50:46 osmc hyperiond[321]: Hyperion Ambilight Deamon (321)
ssh in: Sep 19 22:50:46 osmc hyperiond[321]: Version : V1.03.3 (brindosch-2fbbcff/2f01dfa-1495880388
ssh in: Sep 19 22:50:46 osmc hyperiond[321]: Build Time: Jun 3 2017 02:06:37
ssh in: Sep 19 22:50:46 osmc hyperiond[321]: ERROR: No valid config found
ssh in: Sep 19 22:50:46 osmc systemd[1]: hyperion.service: main process exited, code=exited, status=1/FAILURE
ssh in: Sep 19 22:50:46 osmc systemd[1]: Unit hyperion.service entered failed state.
ssh in: Sep 19 22:50:46 osmc systemd[1]: hyperion.service holdoff time over, scheduling restart.
ssh in: Sep 19 22:50:46 osmc systemd[1]: Stopping Hyperion Systemd service...
ssh in: Sep 19 22:50:47 osmc systemd[1]: Starting Hyperion Systemd service...
ssh in: Sep 19 22:50:47 osmc systemd[1]: Started Hyperion Systemd service.
ssh in: Sep 19 22:50:47 osmc hyperiond[328]: Hyperion Ambilight Deamon (328)
ssh in: Sep 19 22:50:47 osmc hyperiond[328]: Version : V1.03.3 (brindosch-2fbbcff/2f01dfa-1495880388
ssh in: Sep 19 22:50:47 osmc hyperiond[328]: Build Time: Jun 3 2017 02:06:37
ssh in: Sep 19 22:51:03 osmc hyperiond[328]: ERROR: No valid config found
ssh in: Sep 19 22:51:03 osmc systemd[1]: hyperion.service: main process exited, code=exited, status=1/FAILURE
ssh in: Sep 19 22:51:03 osmc systemd[1]: Unit hyperion.service entered failed state.
ssh in: Sep 19 22:51:03 osmc systemd[1]: hyperion.service holdoff time over, scheduling restart.
ssh in: Sep 19 22:51:03 osmc systemd[1]: Stopping Hyperion Systemd service...
ssh in: Sep 19 22:51:03 osmc systemd[1]: Starting Hyperion Systemd service...
ssh in: Sep 19 22:51:03 osmc systemd[1]: Started Hyperion Systemd service.
ssh in: Sep 19 22:51:04 osmc hyperiond[341]: Hyperion Ambilight Deamon (341)
ssh in: Sep 19 22:51:04 osmc hyperiond[341]: Version : V1.03.3 (brindosch-2fbbcff/2f01dfa-1495880388
ssh in: Sep 19 22:51:04 osmc hyperiond[341]: Build Time: Jun 3 2017 02:06:37
ssh in: Sep 19 22:51:04 osmc hyperiond[341]: ERROR: No valid config found
ssh in: Sep 19 22:51:04 osmc systemd[1]: hyperion.service: main process exited, code=exited, status=1/FAILURE
ssh in: Sep 19 22:51:04 osmc systemd[1]: Unit hyperion.service entered failed state.
ssh in: Sep 19 22:51:04 osmc systemd[1]: hyperion.service holdoff time over, scheduling restart.
ssh in: Sep 19 22:51:04 osmc systemd[1]: Stopping Hyperion Systemd service...
ssh in: Sep 19 22:51:04 osmc systemd[1]: Starting Hyperion Systemd service...
ssh in: Sep 19 22:51:04 osmc systemd[1]: Started Hyperion Systemd service.
ssh in: Sep 19 22:51:05 osmc hyperiond[362]: Hyperion Ambilight Deamon (362)
ssh in: Sep 19 22:51:05 osmc hyperiond[362]: Version : V1.03.3 (brindosch-2fbbcff/2f01dfa-1495880388
ssh in: Sep 19 22:51:05 osmc hyperiond[362]: Build Time: Jun 3 2017 02:06:37
ssh in: Sep 19 22:51:05 osmc hyperiond[362]: ERROR: No valid config found
ssh in: Sep 19 22:51:05 osmc systemd[1]: hyperion.service: main process exited, code=exited, status=1/FAILURE
ssh in: Sep 19 22:51:05 osmc systemd[1]: Unit hyperion.service entered failed state.
ssh in: Sep 19 22:51:05 osmc systemd[1]: hyperion.service holdoff time over, scheduling restart.
ssh in: Sep 19 22:51:05 osmc systemd[1]: Stopping Hyperion Systemd service...
ssh in: Sep 19 22:51:05 osmc systemd[1]: Starting Hyperion Systemd service...
ssh in: Sep 19 22:51:05 osmc systemd[1]: hyperion.service start request repeated too quickly, refusing to start.
ssh in: Sep 19 22:51:05 osmc systemd[1]: Failed to start Hyperion Systemd service.
ssh in: Sep 19 22:51:05 osmc systemd[1]: Unit hyperion.service entered failed state.
sftp Send Hyperion Config - Sourcepath: , Targetpath: /etc/hyperion/, Filename: hyperion.config.json
Alles anzeigen
Can you get an extract from "get log" of hypercon in the ssh tab?
If the error is something like "no valid config found" or something similar to it, then check the name of the config file, it HAS to be hyperion.config.jason
I'll try again tonight. But yeah that was usually the error, but I would check and it was named properly.
I have successfully tested my setup with a python script from adafruit using a RPi model b, 60/LEDs per m WS2812b, both connected to same PSU and with a micro controller (level converter) was able to test it with all 300 LEDs.
Here is where I'm pretty baffled. I have tried installation of Hyperion within OSMC, Raspbian, Openelec, Kodi. Tried manually through commands in putty and through the seemingly super simple method of Hypercon. Installation every time shows successful. However this is where I'm stuck. The lights don't do anything at this point, I can't seem to send config changes to the config in the Hyperion folder, and manually doing it is fine, but still no success. When I hit start it fails immediately, typically giving me a error of not finding config file, or just failed to sync. I'm not sure what I'm doing wrong.
Any guidance would be appreciated.
I have successfully tested my setup with a python script from adafruit using a RPi model b, 60/LEDs per m WS2812b, both connected to same PSU and with a micro controller (level converter) was able to test it with all 300 LEDs.
Here is where I'm pretty baffled. I have tried installation of Hyperion within OSMC, Raspbian, Openelec, Kodi. Tried manually through commands in putty and through the seemingly super simple method of Hypercon. Installation every time shows successful. However this is where I'm stuck. The lights don't do anything at this point, I can't seem to send config changes to the config in the Hyperion folder, and manually doing it is fine, but still no success. When I hit start it fails immediately, typically giving me a error of not finding config file, or just failed to sync. I'm not sure what I'm doing wrong.
Any guidance would be appreciated.
Update: installed fresh OS on formatted SD and things aren't freezing anymore. Hyperion just refuses to start. I tested python script to insure hardware is working, and I can run all 300 LEDs off it. If it makes a difference I'm using a level converter in the mix, however I have tried without it. Seems maybe software related.
I have a RPi 1 Model b paired with some WS2812b pwm LEDS. I can't for the life of me figure out where I'm getting my issues. I have tried OSMC, Raspbian, Openelec, and Kodi builds. I managed to have like 5 leds of my 5m 60led/m ws2812b light up for like 5 min, but other than that nothing. I keep getting and odd issue acroos the different OS's. When installation of Hyperion from Hypercon Is finished it fails to auto reboot the OS. No lights are on. I am forced then to manually reboot from either terminal or removing the micro usb it. Either method gives me no leds on start, however, after the boot sequence starts I eventually cant boot into the os. It freezes. Raspbian everything goes smoothly, even shows Hyperion starting (again still no lights) until something along the lines of "printk messages dropped" comes up and the OS freezes. OSMC i have the Hyperion log attached, however, it reacted the same way as Raspbian accept i got an error:
Zitat"Kernel panic - not syncing: Fatal expectation in interruption"
---{ end kernel panic - not syncing: Fatal expectation in interruption
random:crng init done
SSH Traffic:
ssh connected
ssh out: cd /tmp && wget -nv -N https://raw.github.com/hyperion-project/hyperion/master/bin/install_hyperion.sh && chmod +x install_hyperion.sh && sudo sh ./install_hyperion.sh HyperConInstall ; rm install_hyperion.sh
ssh out: Last-modified header missing -- time-stamps turned off.
ssh out: 2017-09-19 22:39:01 URL:https://raw.githubusercontent.com/hyperion-project/hyperion/master/bin/install_hyperion.sh [14552/14552] -> "install_hyperion.sh" [1]
ssh in: *******************************************************************************
ssh in: This script will install/update Hyperion Ambient Light
ssh in: Created by brindosch - hyperion-project.org - the official Hyperion source.
ssh in: *******************************************************************************
ssh in: ---> Stop Hyperion, if necessary
ssh in: ---> Install/Update Hyperion dependencies (This may take a while)
ssh out: debconf: unable to initialize frontend: Dialog
ssh out: debconf: (Dialog frontend will not work on a dumb terminal, an emacs shell buffer, or without a controlling terminal.)
ssh out: debconf: falling back to frontend: Readline
ssh out: debconf: unable to initialize frontend: Readline
ssh out: debconf: (Can't locate Term/ReadLine.pm in @INC (you may need to install the Term::ReadLine module) (@INC contains: /etc/perl /usr/local/lib/arm-linux-gnueabihf/perl/5.20.2 /usr/local/share/perl/5.20.2 /usr/lib/arm-linux-gnueabihf/perl5/5.20 /usr/share/perl5 /usr/lib/arm-linux-gnueabihf/perl/5.20 /usr/share/perl/5.20 /usr/local/lib/site_perl .) at /usr/share/perl5/Debconf/FrontEnd/Readline.pm line 7, <> line 22.)
ssh out: debconf: falling back to frontend: Teletype
ssh out: dpkg-preconfigure: unable to re-open stdin:
ssh in: Selecting previously unselected package fontconfig.
ssh in: (Reading database ...
ssh in: (Reading database ... 5%
ssh in: (Reading database ... 10%
ssh in: (Reading database ... 15%
ssh in: (Reading database ... 20%
ssh in: (Reading database ... 25%
ssh in: (Reading database ... 30%
ssh in: (Reading database ... 35%
ssh in: (Reading database ... 40%
ssh in: (Reading database ... 45%
ssh in: (Reading database ... 50%
ssh in: (Reading database ... 55%
ssh in: (Reading database ... 60%
ssh in: (Reading database ... 65%
ssh in: (Reading database ... 70%
ssh in: (Reading database ... 75%
ssh in: (Reading database ... 80%
ssh in: (Reading database ... 85%
ssh in: (Reading database ... 90%
ssh in: (Reading database ... 95%
ssh in: (Reading database ... 100%
ssh in: (Reading database ... 23148 files and directories currently installed.)
ssh in: Preparing to unpack .../fontconfig_2.11.0-6.3+deb8u1_armhf.deb ...
ssh in: Unpacking fontconfig (2.11.0-6.3+deb8u1) ...
ssh in: Selecting previously unselected package libxau6:armhf.
ssh in: Preparing to unpack .../libxau6_1%3a1.0.8-1_armhf.deb ...
ssh in: Unpacking libxau6:armhf (1:1.0.8-1) ...
ssh in: Selecting previously unselected package x11-common.
ssh in: Preparing to unpack .../x11-common_1%3a7.7+7_all.deb ...
ssh in: Unpacking x11-common (1:7.7+7) ...
ssh in: Selecting previously unselected package libice6:armhf.
ssh in: Preparing to unpack .../libice6_2%3a1.0.9-1_armhf.deb ...
ssh in: Unpacking libice6:armhf (2:1.0.9-1) ...
ssh in: Selecting previously unselected package libsm6:armhf.
ssh in: Preparing to unpack .../libsm6_2%3a1.2.2-1_armhf.deb ...
ssh in: Unpacking libsm6:armhf (2:1.2.2-1) ...
ssh in: Selecting previously unselected package libxdmcp6:armhf.
ssh in: Preparing to unpack .../libxdmcp6_1%3a1.1.1-1_armhf.deb ...
ssh in: Unpacking libxdmcp6:armhf (1:1.1.1-1) ...
ssh in: Selecting previously unselected package libxcb1:armhf.
ssh in: Preparing to unpack .../libxcb1_1.10-3_armhf.deb ...
ssh in: Unpacking libxcb1:armhf (1.10-3) ...
ssh in: Selecting previously unselected package libx11-data.
ssh in: Preparing to unpack .../libx11-data_2%3a1.6.2-3_all.deb ...
ssh in: Unpacking libx11-data (2:1.6.2-3) ...
ssh in: Selecting previously unselected package libx11-6:armhf.
ssh in: Preparing to unpack .../libx11-6_2%3a1.6.2-3_armhf.deb ...
ssh in: Unpacking libx11-6:armhf (2:1.6.2-3) ...
ssh in: Selecting previously unselected package libxt6:armhf.
ssh in: Preparing to unpack .../libxt6_1%3a1.1.4-1_armhf.deb ...
ssh in: Unpacking libxt6:armhf (1:1.1.4-1) ...
ssh in: Selecting previously unselected package libaudio2:armhf.
ssh in: Preparing to unpack .../libaudio2_1.9.4-3_armhf.deb ...
ssh in: Unpacking libaudio2:armhf (1.9.4-3) ...
ssh in: Selecting previously unselected package libjpeg8:armhf.
ssh in: Preparing to unpack .../libjpeg8_8d1-2_armhf.deb ...
ssh in: Unpacking libjpeg8:armhf (8d1-2) ...
ssh in: Selecting previously unselected package libmng1:armhf.
ssh in: Preparing to unpack .../libmng1_1.0.10+dfsg-3.1_armhf.deb ...
ssh in: Unpacking libmng1:armhf (1.0.10+dfsg-3.1) ...
ssh in: Selecting previously unselected package qtcore4-l10n.
ssh in: Preparing to unpack .../qtcore4-l10n_4%3a4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1_all.deb ...
ssh in: Unpacking qtcore4-l10n (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Selecting previously unselected package libqtcore4:armhf.
ssh in: Preparing to unpack .../libqtcore4_4%3a4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1_armhf.deb ...
ssh in: Unpacking libqtcore4:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Selecting previously unselected package libqt4-xml:armhf.
ssh in: Preparing to unpack .../libqt4-xml_4%3a4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1_armhf.deb ...
ssh in: Unpacking libqt4-xml:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Selecting previously unselected package libqtdbus4:armhf.
ssh in: Preparing to unpack .../libqtdbus4_4%3a4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1_armhf.deb ...
ssh in: Unpacking libqtdbus4:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Selecting previously unselected package libqt4-network:armhf.
ssh in: Preparing to unpack .../libqt4-network_4%3a4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1_armhf.deb ...
ssh in: Unpacking libqt4-network:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Selecting previously unselected package libxext6:armhf.
ssh in: Preparing to unpack .../libxext6_2%3a1.3.3-1_armhf.deb ...
ssh in: Unpacking libxext6:armhf (2:1.3.3-1) ...
ssh in: Selecting previously unselected package libxrender1:armhf.
ssh in: Preparing to unpack .../libxrender1_1%3a0.9.8-1_armhf.deb ...
ssh in: Unpacking libxrender1:armhf (1:0.9.8-1) ...
ssh in: Selecting previously unselected package libqtgui4:armhf.
ssh in: Preparing to unpack .../libqtgui4_4%3a4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1_armhf.deb ...
ssh in: Unpacking libqtgui4:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Selecting previously unselected package libusb-1.0-0:armhf.
ssh in: Preparing to unpack .../libusb-1.0-0_2%3a1.0.19-1_armhf.deb ...
ssh in: Unpacking libusb-1.0-0:armhf (2:1.0.19-1) ...
ssh in: Processing triggers for systemd (215-17+deb8u7) ...
ssh in: Setting up fontconfig (2.11.0-6.3+deb8u1) ...
ssh in: Regenerating fonts cache... done.
ssh in: Setting up libxau6:armhf (1:1.0.8-1) ...
ssh in: Setting up x11-common (1:7.7+7) ...
ssh in: debconf: unable to initialize frontend: Dialog
ssh in: debconf: (Dialog frontend will not work on a dumb terminal, an emacs shell buffer, or without a controlling terminal.)
ssh in: debconf: falling back to frontend: Readline
ssh in: debconf: unable to initialize frontend: Readline
ssh in: debconf: (Can't locate Term/ReadLine.pm in @INC (you may need to install the Term::ReadLine module) (@INC contains: /etc/perl /usr/local/lib/arm-linux-gnueabihf/perl/5.20.2 /usr/local/share/perl/5.20.2 /usr/lib/arm-linux-gnueabihf/perl5/5.20 /usr/share/perl5 /usr/lib/arm-linux-gnueabihf/perl/5.20 /usr/share/perl/5.20 /usr/local/lib/site_perl .) at /usr/share/perl5/Debconf/FrontEnd/Readline.pm line 7.)
ssh in: debconf: falling back to frontend: Teletype
ssh in: /var/lib/dpkg/info/x11-common.postinst: 697: /var/lib/dpkg/info/x11-common.postinst: update-rc.d: not found
ssh in: dpkg: error processing package x11-common (--configure):
ssh in: subprocess installed post-installation script returned error exit status 127
ssh in: dpkg: dependency problems prevent configuration of libice6:armhf:
ssh in: libice6:armhf depends on x11-common; however:
ssh in: Package x11-common is not configured yet.
ssh in: dpkg: error processing package libice6:armhf (--configure):
ssh in: dependency problems - leaving unconfigured
ssh in: dpkg: dependency problems prevent configuration of libsm6:armhf:
ssh in: libsm6:armhf depends on libice6 (>= 1:1.0.0); however:
ssh in: Package libice6:armhf is not configured yet.
ssh in: dpkg: error processing package libsm6:armhf (--configure):
ssh in: dependency problems - leaving unconfigured
ssh in: Setting up libxdmcp6:armhf (1:1.1.1-1) ...
ssh in: Setting up libxcb1:armhf (1.10-3) ...
ssh in: Setting up libx11-data (2:1.6.2-3) ...
ssh in: Setting up libx11-6:armhf (2:1.6.2-3) ...
ssh in: dpkg: dependency problems prevent configuration of libxt6:armhf:
ssh in: libxt6:armhf depends on libice6 (>= 1:1.0.0); however:
ssh in: Package libice6:armhf is not configured yet.
ssh in: libxt6:armhf depends on libsm6; however:
ssh in: Package libsm6:armhf is not configured yet.
ssh in: dpkg: error processing package libxt6:armhf (--configure):
ssh in: dependency problems - leaving unconfigured
ssh in: dpkg: dependency problems prevent configuration of libaudio2:armhf:
ssh in: libaudio2:armhf depends on libxt6; however:
ssh in: Package libxt6:armhf is not configured yet.
ssh in: dpkg: error processing package libaudio2:armhf (--configure):
ssh in: dependency problems - leaving unconfigured
ssh in: Setting up libjpeg8:armhf (8d1-2) ...
ssh in: Setting up libmng1:armhf (1.0.10+dfsg-3.1) ...
ssh in: Setting up qtcore4-l10n (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Setting up libqtcore4:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Setting up libqt4-xml:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Setting up libqtdbus4:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Setting up libqt4-network:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1+rpi1) ...
ssh in: Setting up libxext6:armhf (2:1.3.3-1) ...
ssh in: Setting up libxrender1:armhf (1:0.9.8-1) ...
ssh in: dpkg: dependency problems prevent configuration of libqtgui4:armhf:
ssh in: libqtgui4:armhf depends on libaudio2; however:
ssh in: Package libaudio2:armhf is not configured yet.
ssh in: libqtgui4:armhf depends on libice6 (>= 1:1.0.0); however:
ssh in: Package libice6:armhf is not configured yet.
ssh in: libqtgui4:armhf depends on libsm6; however:
ssh in: Package libsm6:armhf is not configured yet.
ssh in: dpkg: error processing package libqtgui4:armhf (--configure):
ssh in: dependency problems - leaving unconfigured
ssh in: Setting up libusb-1.0-0:armhf (2:1.0.19-1) ...
ssh in: Processing triggers for libc-bin (2.19-18+deb8u10) ...
ssh in: Processing triggers for systemd (215-17+deb8u7) ...
ssh in: Errors were encountered while processing:
ssh in: x11-common
ssh in: libice6:armhf
ssh in: libsm6:armhf
ssh in: libxt6:armhf
ssh in: libaudio2:armhf
ssh in: libqtgui4:armhf
ssh out: E: Sub-process /usr/bin/dpkg returned an error code (1)
ssh in: ---> Raspberry Pi found, but SPI is not set, we write "dtparam=spi=on" to /boot/config.txt
ssh in: ---> Downloading the appropriate Hyperion release
ssh out: 2017-09-19 22:43:12 URL:https://cytranet.dl.sourceforge.net/project/hyperion-project/release/hyperion_rpi3_osmc.tar.gz [1639953/1639953] -> "-" [1]
ssh in: ---> Installing systemd script
ssh in: ---> Modify systemd script for OSMC usage
ssh in: ---> Starting Hyperion
ssh in: *******************************************************************************
ssh in: Hyperion Installation/Update finished!
ssh in: Please download the latest HyperCon version to benefit from new features!
ssh in: To create a config, follow the HyperCon Guide at our Wiki (EN/DE)!
ssh in: Wiki: wiki.hyperion-project.org Webpage: www.hyperion-project.org
ssh in: *******************************************************************************
ssh in: Rebooting now, we added dtparam=spi=on to config.txt
ssh disconnected
ssh connected
ssh out: sudo journalctl -u hyperion.service 2>/dev/null
ssh in: -- Logs begin at Tue 2017-09-19 22:50:37 -01, end at Tue 2017-09-19 22:53:01 -01. --
ssh in: Sep 19 22:50:40 osmc systemd[1]: Starting Hyperion Systemd service...
ssh in: Sep 19 22:50:40 osmc systemd[1]: Started Hyperion Systemd service.
ssh in: Sep 19 22:50:44 osmc hyperiond[244]: Hyperion Ambilight Deamon (244)
ssh in: Sep 19 22:50:44 osmc hyperiond[244]: Version : V1.03.3 (brindosch-2fbbcff/2f01dfa-1495880388
ssh in: Sep 19 22:50:44 osmc hyperiond[244]: Build Time: Jun 3 2017 02:06:37
ssh in: Sep 19 22:50:45 osmc hyperiond[244]: ERROR: No valid config found
ssh in: Sep 19 22:50:45 osmc systemd[1]: hyperion.service: main process exited, code=exited, status=1/FAILURE
ssh in: Sep 19 22:50:45 osmc systemd[1]: Unit hyperion.service entered failed state.
ssh in: Sep 19 22:50:46 osmc systemd[1]: hyperion.service holdoff time over, scheduling restart.
ssh in: Sep 19 22:50:46 osmc systemd[1]: Stopping Hyperion Systemd service...
ssh in: Sep 19 22:50:46 osmc systemd[1]: Starting Hyperion Systemd service...
ssh in: Sep 19 22:50:46 osmc systemd[1]: Started Hyperion Systemd service.
ssh in: Sep 19 22:50:46 osmc hyperiond[321]: Hyperion Ambilight Deamon (321)
ssh in: Sep 19 22:50:46 osmc hyperiond[321]: Version : V1.03.3 (brindosch-2fbbcff/2f01dfa-1495880388
ssh in: Sep 19 22:50:46 osmc hyperiond[321]: Build Time: Jun 3 2017 02:06:37
ssh in: Sep 19 22:50:46 osmc hyperiond[321]: ERROR: No valid config found
ssh in: Sep 19 22:50:46 osmc systemd[1]: hyperion.service: main process exited, code=exited, status=1/FAILURE
ssh in: Sep 19 22:50:46 osmc systemd[1]: Unit hyperion.service entered failed state.
ssh in: Sep 19 22:50:46 osmc systemd[1]: hyperion.service holdoff time over, scheduling restart.
ssh in: Sep 19 22:50:46 osmc systemd[1]: Stopping Hyperion Systemd service...
ssh in: Sep 19 22:50:47 osmc systemd[1]: Starting Hyperion Systemd service...
ssh in: Sep 19 22:50:47 osmc systemd[1]: Started Hyperion Systemd service.
ssh in: Sep 19 22:50:47 osmc hyperiond[328]: Hyperion Ambilight Deamon (328)
ssh in: Sep 19 22:50:47 osmc hyperiond[328]: Version : V1.03.3 (brindosch-2fbbcff/2f01dfa-1495880388
ssh in: Sep 19 22:50:47 osmc hyperiond[328]: Build Time: Jun 3 2017 02:06:37
ssh in: Sep 19 22:51:03 osmc hyperiond[328]: ERROR: No valid config found
ssh in: Sep 19 22:51:03 osmc systemd[1]: hyperion.service: main process exited, code=exited, status=1/FAILURE
ssh in: Sep 19 22:51:03 osmc systemd[1]: Unit hyperion.service entered failed state.
ssh in: Sep 19 22:51:03 osmc systemd[1]: hyperion.service holdoff time over, scheduling restart.
ssh in: Sep 19 22:51:03 osmc systemd[1]: Stopping Hyperion Systemd service...
ssh in: Sep 19 22:51:03 osmc systemd[1]: Starting Hyperion Systemd service...
ssh in: Sep 19 22:51:03 osmc systemd[1]: Started Hyperion Systemd service.
ssh in: Sep 19 22:51:04 osmc hyperiond[341]: Hyperion Ambilight Deamon (341)
ssh in: Sep 19 22:51:04 osmc hyperiond[341]: Version : V1.03.3 (brindosch-2fbbcff/2f01dfa-1495880388
ssh in: Sep 19 22:51:04 osmc hyperiond[341]: Build Time: Jun 3 2017 02:06:37
ssh in: Sep 19 22:51:04 osmc hyperiond[341]: ERROR: No valid config found
ssh in: Sep 19 22:51:04 osmc systemd[1]: hyperion.service: main process exited, code=exited, status=1/FAILURE
ssh in: Sep 19 22:51:04 osmc systemd[1]: Unit hyperion.service entered failed state.
ssh in: Sep 19 22:51:04 osmc systemd[1]: hyperion.service holdoff time over, scheduling restart.
ssh in: Sep 19 22:51:04 osmc systemd[1]: Stopping Hyperion Systemd service...
ssh in: Sep 19 22:51:04 osmc systemd[1]: Starting Hyperion Systemd service...
ssh in: Sep 19 22:51:04 osmc systemd[1]: Started Hyperion Systemd service.
ssh in: Sep 19 22:51:05 osmc hyperiond[362]: Hyperion Ambilight Deamon (362)
ssh in: Sep 19 22:51:05 osmc hyperiond[362]: Version : V1.03.3 (brindosch-2fbbcff/2f01dfa-1495880388
ssh in: Sep 19 22:51:05 osmc hyperiond[362]: Build Time: Jun 3 2017 02:06:37
ssh in: Sep 19 22:51:05 osmc hyperiond[362]: ERROR: No valid config found
ssh in: Sep 19 22:51:05 osmc systemd[1]: hyperion.service: main process exited, code=exited, status=1/FAILURE
ssh in: Sep 19 22:51:05 osmc systemd[1]: Unit hyperion.service entered failed state.
ssh in: Sep 19 22:51:05 osmc systemd[1]: hyperion.service holdoff time over, scheduling restart.
ssh in: Sep 19 22:51:05 osmc systemd[1]: Stopping Hyperion Systemd service...
ssh in: Sep 19 22:51:05 osmc systemd[1]: Starting Hyperion Systemd service...
ssh in: Sep 19 22:51:05 osmc systemd[1]: hyperion.service start request repeated too quickly, refusing to start.
ssh in: Sep 19 22:51:05 osmc systemd[1]: Failed to start Hyperion Systemd service.
ssh in: Sep 19 22:51:05 osmc systemd[1]: Unit hyperion.service entered failed state.
sftp Send Hyperion Config - Sourcepath: , Targetpath: /etc/hyperion/, Filename: hyperion.config.json
Alles anzeigen
If I reboot, Hyperion is no longer installed and there is no config file, so I have to start the entire process again.
Update: With this build of OSMC it looks like it's completely corrupt. It gives the same error on every boot, and goes no further.
PLEASE HELP ME OBI-WAN
How did you solve this after?
Thanks for replying. Only similar instructions I'm finding are built on breadboards. That normal? Know any posts of hand or a guide that uses it and explains the connecting pattern.
Alles anzeigenNo arduino necessary. It I would recommend a level shifter.
There are 3 led driver types that support the ws2812 leds.
Ws2812b - rpi1 only, don't use
Ws281x - good for any pi and uses a pwm capable pin. Conflicts with analog audio
May also cause dma conflicts
Ws2812spi - good for any Pi and uses the SPI MOSI pin but needs a fixed core_freq
I already have the WS2812B now so I'm committed. I found this from some research in the forums here. That's all I need? One of those attached to the pi 2?
I have learned a lesson that buying items based on a single guide should be priority if your unfamiliar with any of this to begin with. I have an LED PSU with 5v 30a, a RPi 2, and a WS2812B LED strip 5m 60leds. What I have since realized since these things arriving, is that I do not have the 4 contacts on the LEDs, the LEDs I have only have 3. I'm figuring out it seems that I cannot use a RPi 2 the PSU and LEDs only, because of the lack of that extra contact.
TLDR if the base setup I currently have is a led power supply, a RPi 2 v2, and a strip of WS2812B. Than I need an audrino to add into the mix to get it working? Is this correct?
Alles anzeigenHi
That power supply is inadequate, it's only 2.1 amp.
I would be guessing at your actual led count. However the calculation to figure you own supply amperage needs are:
Each "pixel" contains 3 LED's (Red, Green, Blue) each LED can draw approximately 20 milliamps. So each pixel can draw 60 milliamps at full power. So if you are using say 250 pixels at 60 milliamps per pixel that's 15 amps. it can draw at full brightness. However you also want a bit of wiggle room so a power supply with a bit more amperage would be a better choice.
Hope it's of help.
How about 30amps? Letour LED Power Supply 5V 30A AC 96V-240V Converter Adapter DC S-150W-5 Power Supply for LED Lighting,LED Strip,CCTV
I'm about to start putting together a Hyperion "Ambilight" setup. One of the things I forgot was a PSU for the LEDs. I am using 60LEDs per meter WS2812B version. According to FAQ, I'm looking at 18watts per meter. For my 50 inch tv I was thinking 3.5 meters should be good (haven't had a chance to measure as LEDs aren't in yet) So at 5v I think should be about 12.6amps? So I was looking at this (