Posts by gooners4life

Got a pi zero 2 w. Yeelights Don't work. Is it cause specs are low?

< ----- Current Log --------------------------- >

2025-05-09T11:57:57.400Z [IMAGETOLED|Yeelight] (WARNING) Mapping LED/light [0]. The current mapping area contains 4096 pixels which is huge. Therefore every 2 pixels will be skipped. You can enable reduced processing to hide that warning.

2025-05-15T19:49:08.446Z [SETTINGSMGR|Yeelight] (WARNING) Fixing json data!

2025-05-15T19:49:08.486Z [SETTINGSMGR|Yeelight] (WARNING) Config Fix: [root].device.autoStart: Create property: autoStart with value: True

2025-05-15T19:49:08.486Z [SETTINGSMGR|Yeelight] (WARNING) Config Fix: [root].device.enableAttempts: Create property: enableAttempts with value: 12

2025-05-15T19:49:08.487Z [SETTINGSMGR|Yeelight] (WARNING) Config Fix: [root].device.enableAttemptsInterval: Create property: enableAttemptsInterval with value: 15

I just bought a Pi zero 2w and back lights are working but I need something strong to run the Yeelight with it.
Will give your solution a try

Tried it, but did not work. Anyway to downgrade the Hyperion version to see if it fixes it?

tried it on GPIO 17 and no luck . Its like the GPIO doesn't want to send out a signal and Hyperion is root.

LED are all working. Had a ESP8266 WLED board to test it with. Nothing on the logs.

Tried the recommended solution but no luck

Quote from Marxon

Hi,

what exactly do you mean with "rebuilt Hyperion"?

Did you rebuild the software or your hardware setup?

Was it working before?

Is the single led fully working and controllable with hyperion?

Best regards

Marxon

Display More

Reformatted the SD card. I think new update may have broken it. Just a white light

Rebuilt Hyperion and now only 1 LED is working. I selected WS281X

Any reason why it's only 1 LED?

BTF LIGHTING Flexible Individually Addressable Non waterproof

Why does my pi doesn't want to the WiFi most of the times. How do I fix this, so I can access the web UI

Will Android Grabber be updated soon? Doesn't work with TLC TVs.
Connects to Hyperion server fine but doesn't do nothing

same issue. The app hasn't been updated for a long time.

I am considering doing my 2nd Hyperion project but I want to know if Hyperion supports Goolge TV as I will not use an HDMI Video capture card.

I might sound stupid but does any know of dimmable WLED bulbs that work with a dimable switch?

I got 4 yeelights on the yeelight app ready on the network and I can ping them on the PI 4 but they are failing to connect.

Any clue on how to fix it?

2024-06-11T19:14:46.127Z [LEDDEVICE|yeelight] (ERROR) Failed to open [192.168.1.x]
2024-06-11T19:14:46.127Z [LEDDEVICE|yeelight] (ERROR) Device disabled, device 'yeelight' signals error: 'All Yeelights failed to be opened!'
2024-06-11T19:15:01.177Z [LEDDEVICE|yeelight] (ERROR) Yeelight device '192.168.1.x' signals error: 'Connection refused'

solved my own issue. saw a setting in the yeelight app and set it to allow lan control

Bought these led from Amazon but they keep on crashing. Wled LED bought click here

Which firmware will it stop it from crashing?

looks good

upload a video mate

click here to watch video

I setup LED on bottom of the desk but they don't seem to sync well.
How would I do the LED setup? I have led strip running from all the left side to all front and all right side.

I have added LED on back of monitor which looks good but I have some spare LED left over.

I was wondering if I should put the LED under my desk. Should I put it on back of the desk and sides or front and sides? Or any other suggestions?

I have spare WS2812B LED Strip and would like to connect it to Hyperion. How would I go about doing that if I have one already connected to a Pi4?