Beiträge von Lord-Grey

Good to hear to it works in general.
Did you found a working setup with Arduino and Flirc?

Looks like you have two USB devices

crw-rw---- 1 root dialout 166, 0 Nov 11 13:09 /dev/ttyACM0
crw-rw---- 1 root dialout 166, 1 Nov 11 13:19 /dev/ttyACM1

Have you tried configuring "/dev/ttyACM1" ?

Or could you execute the following commands? Does one come back with "Ada"?

1.
cat /dev/ttyACM0

To stop press, ctrl-C

2.
cat /dev/ttyACM1

To stop press, ctrl-C

3.
dmesg | grep usb

4.

dmesg | grep tty

Please share the output...

Keine Ahnung...
Wenn der Browser die URL nicht auflösen kann, kann Hyperion das auch nicht...

Was kommt beim nslookup auf die IP-Adresse?

And that is the problem....
It has nothing to do with Hyperion, but that the hostname is not resolved on your local network...

Suggest you check the name assigned in the Fritzbox.

What does the url I asked you to run in the browser return back?

Could you also ping me which Hyperion build you are using?
UI: System->Hyperion about

Hi

Good that it is working now.
I am of the opinion that it should also with the hostname and with and without domain.

What does the url I asked you to run in the browser return back?

sorry, I had a typo....

Could you do a ls -la /dev/tty*

Hey

the communication with the bridge already fails at the very beginning.
You see it that the Bdrige details are all empty.
That the device is not put in error at that point in time is a different story...

2020-11-10T22:26:22.410Z [hyperiond LEDDEVICE] (DEBUG) (ProviderRestApi.cpp:124:get()) GET: [http://philips-hue.fritz.box:80/api/-ThXP8g2K2Sn7BOdj9JScFsi******************/]
2020-11-10T22:26:22.413Z [hyperiond LEDDEVICE] (DEBUG) (ProviderRestApi.cpp:182:getResponse()) Reply.httpStatusCode [0]
....
2020-11-11T10:50:26.248Z [hyperiond LEDDEVICE] (DEBUG) (LedDevicePhilipsHue.cpp:417:log()) Bridge Name                   :
2020-11-11T10:50:26.248Z [hyperiond LEDDEVICE] (DEBUG) (LedDevicePhilipsHue.cpp:417:log()) Model                         :
2020-11-11T10:50:26.248Z [hyperiond LEDDEVICE] (DEBUG) (LedDevicePhilipsHue.cpp:417:log()) Bridge-ID                     :
2020-11-11T10:50:26.248Z [hyperiond LEDDEVICE] (DEBUG) (LedDevicePhilipsHue.cpp:417:log()) SoftwareVersion               :
2020-11-11T10:50:26.249Z [hyperiond LEDDEVICE] (DEBUG) (LedDevicePhilipsHue.cpp:417:log()) API-Version                   : 0.0.0
2020-11-11T10:50:26.249Z [hyperiond LEDDEVICE] (DEBUG) (LedDevicePhilipsHue.cpp:417:log()) EntertainmentReady            : 0
2020-11-11T10:50:26.249Z [hyperiond LEDDEVICE] (ERROR) Device disabled, device 'philipshue' signals error: 'No light-IDs found at the Philips Hue Bridge'

Could you give it a try with the following reconfigurations:

a) Use the hostname without domain (i.e. "philips-hue")
b) Use the IP-address of the bridge

c) Open the following URL via a Browser. What do you get back?
Replace the client name with the not masked one.

http://philips-hue.fritz.box:8…JScFsi******************/

Thank you!

I checked the log again

I looks like that your bridge is reachable, but could not access the values:

2020-11-10T21:43:35.306Z [hyperiond LEDDEVICE] (DEBUG) (ProviderRestApi.cpp:124:get()) GET: [http://philips-hue.fritz.box:80/api/-******************************************/groups/6]
2020-11-10T21:43:35.308Z [hyperiond LEDDEVICE] (DEBUG) (ProviderRestApi.cpp:182:getResponse()) Reply.httpStatusCode [0]

Valid answer from the bridge should be a StatusCode = 200 rather than 0

2020-11-11T10:59:24.337 hyperiond LEDDEVICE    : <DEBUG> ProviderRestApi.cpp:179:getResponse() | Reply.httpStatusCode [200]

Is your "Benutzername" correct? It confuses me that it starts with a minus "-"
Could you provide a full log, please?

Please enable

You might need putting Settings Level to "Expert" first.

You could share the full log with me privately... Just start a Conversation with me in the Forum.

The error indicates that your system does not provide any serial devices... or the device is busy

2020-11-11T08:31:49.324Z [hyperiond LEDDEVICE] (ERROR) Device disabled, device 'adalight' signals error: 'No serial device found automatically!'

Could you please post more details about your system.
Copy/Paste the System Info from "about hyperion"

In addition, could you do a ls -la /dev/ttyp*

If you running on an rpi, do you have Bluetooth on?

"(ERROR) Device disabled, device 'philipshue' signals error: 'no Streaming Infos in Group found'

Looks like your Group is not configured as an Entertainment-API one....

Did you configure the device via the Wizard?
There you should be also be able to select the appropriate group and test the individual lights in advance ("Identify").

Nach ein paar Zwischenschritten solltest Du hier ankommen:

The error indicates that your Arduino is not found under the name of "ttyACM0".

Give it a try with "auto" and see, if the device identifies itself.
If yes, you will find in the log the name used:

2020-11-11T08:46:44.079 hyperiond LEDDEVICE    : <INFO> found serial device: ttyACM0

Note: Mine is under "ttyACM0", but you should see a different name.

@ModuloFS I reworked the code and hopefully got it fixed.

What would be the best way to get it tested?
Do you compile hyperion yourself, then I will share the updated code files with you.
Or do you need a pre-build package (for what platform - Ubuntu)?

Thanks for sharing.
This problem was identified before and going forward the libCEC will be part of the deb Package Installation process to overcome the manual workaround.

Please see,

https://github.com/hyperion-pr…/blob/master/CHANGELOG.md

Danke für das Teilen Deiner Erfahrung.
Im nächsten Release wird libCEC als Teil der Package Installation dabei sein und der manuelle Workaround entfällt.

see
https://github.com/hyperion-pr…/blob/master/CHANGELOG.md

@jeroen warmerdam

Go to the following link of the PR

https://github.com/hyperion-pr…s?check_run_id=1368607344

Click on Artifacts and you can download a ready build package for your platform.

Zitat von pclin

Das ist aber doch schon ungewöhnlich.
Meines wissens nach sendet hyperion keine Befehle an WLED, und wenn wäre das sich 'Power on'

Beim Hyperion WLED Device schicke ich on bzw. Off Kommandos an WLED
, aber auch nur, wenn ein hyperion Device an oder ausgeschaltet wird bzw. nichts zu Streamen da ist.

Anstatt nur die Konfiguration zu posten, wäre hier ein Debug log hilfreich...
System->Log
Dort sieht man, ob zusätzlich was an oder aus geschaltet wird.
Ansonsten empfehle ich mal einen Effect über die „Fernsteuerung“ d.h. Remote Control zu initiieren.

Edit: Im log findet man auch ggf. Fehlermeldungen. Dann brauchst man nicht zu raten...

@jeroen warmerdam Please re-test with #1075
https://github.com/hyperion-project/hyperion.ng/pull/1075