root is only required for ws281x PWM.
This is also in the Hyperion log, you just have to read it.
300 SK6812 RGBW require max. 15A.
LED power calculator (wled-calculator.github.io)
regards pclin
root is only required for ws281x PWM.
This is also in the Hyperion log, you just have to read it.
300 SK6812 RGBW require max. 15A.
LED power calculator (wled-calculator.github.io)
regards pclin
PC operating system?
Have you tested with internal grabber?
regards pclin
Splitter = 1 IN 2 OUT
OUT 1 > TV
OUT 2 > Grabber
regards pclin
I don't know any of the 3 spitters so all you can do is try and report back.
In terms of features it could be suitable.
regards pclin
Have you increased the SPI buffer size?
regards pclin
Schau mal hier dort sind auch ESP mit LAN Anschluss aufgeführt.
Ich habe einen OLIMEX ESP-32-POE-ISO
gruß pclin
You need a splitter that has 4K 60Hz, HDCP 2.2, EDID management and scaler, the UGREEN is an HDMI switch, since you have an AVR (to which your devices are connected?) you don't need a switch.
Under 20 you won't find anything, Grabber 10, Splitter about 40
regards pclin
Im log kann ich nichts ungewöhnliches sehen, Hyperion funktioniert.
Du hast keinen Grabber konfiguriert?!
Verwende keine Effekte zum Testen, verwende feste Farben, am besten Rot, Grün, Blau und Weiß.
Wenn das funktioniert (alle LED in gleicher Farbe und Helligkeit) kannst du mit Effekten und/oder mit Grabber weiter machen.
Blitzen kann z.B. durch zu hohe Volt an den LEDs, zu lange Data Leitung oder Einstreuungen auf Data passieren.
Bei SK6812 rgbw messe ich immer am Stripe (mitte zwischen den Einspeisepunkten) unter Volllast, weiß und 100% Helligkeit und stelle 4,95 Volt ein.
gruß pclin
root user is only necessary for ws281x PWM.
There are a changes in bookworm, it's best to take a look at the documentation.
regards pclin
With Arduino you cannot achieve the baud rate required for SK6812, which then leads to delays.
regards pclin
Hyperion Debug Log als .txt Datei anhängen.
gruß pclin
The Flatbuffers server must be activated in Hyperion, where you can also see the port that is used.
After you have set everything, restart PicCap once and there should be an entry in Hyperion > Remote Control > webos Flatbuffers Server.
webOS TV 5.2.0 LGwebOSTV
/ # ping -c2 192.168.x.x
64 bytes from 192.168.x.x: icmp_seq=1 ttl=64 time=0.762 ms
64 bytes from 192.168.x.x: icmp_seq=2 ttl=64 time=0.531 ms
--- 192.168.x.x ping statistics ---
2 packets transmitted, 2 received, 0% packet loss, time 999ms
regards pclin
Mit dem Post hilfst du leider keinem weiter der vor dem gleichen Problem steht HD108 zum laufen zu bringen.
gruß pclin
Ich habe meinen Post nochmals editiert, die WAGO Klemme hatte ich vorher nicht richtig gesehen.
gruß pclin
Es fehlt die gemeinsame Masse, oder es gibt da ein Verbindungs- Problem.
Platz 1 fehlende gemeinsame Masse.
Platz 2 mehr als ein Programm oder Instanzen senden gleichzeitig zu den LED's
The Importance of Sharing Grounds (GND)
Die Wichtigkeit von gemeinsamer Masse (GND)
gruß pclin
pi's ip of 192.168.x.x port 19400
If that doesn't work, something else is wrong!
Wifi on LG is usually not a good idea and leads to problems.
regards pclin
Hyperion is also available for Windows, Linux and Mac and there is also internal grabber.
If Hyperion runs on a device without GPIO, you also need a LED controller, e.g. ESP with WLED.
regards pclin