RPi + LibreELEC [HowTo] Install Hyperion.ng on LibreELEC x86_64/RPi (inoffiziell/unofficially)

for me it changes to
Hyperion status: Off
so i have to quit kodi like this
systemctl stop kodi && systemctl restart hyperion.service

and im on alpha6 not 7 as you are, bc 7 is just not ok for me.

--------------------

systemctl disable kodi seems an easy solution but kodi starts anyway.

------------------

systemctl mask kodi, wont start kodi, and hyperion still starts. seems ok, thx


(although, if you happen to know if libreelec has a kindofa start script, that would be still handy for me, for eg, i would boot to textmode, no koidi, and then the sript still could run hyperion on boot. )

 

ok, i missread two lines below, sorry
(any idea on autostart for eg a bash script on libre?)

 

ok, i get it, thanks for the help with kodi not to start, with mask,
but there could be a hyperion releated question like this:

how is it possible to start hyperion if libreelec is set to boot to textmode ?

Hyperion:~ # cat /flash/cmdline.txt
boot=/dev/mmcblk0p1 disk=/dev/mmcblk0p2 quiet textmode

But ok, ill try to find a solution for this, and post it here when i find a way to do it,
until then kodi stays masked

thanks again.

 

Hey guys, I'm pretty new to this but I've read through the entire thread and can't seem to get my hyperion started.
I'm running a Pi Zero w with Libre 9.2.4. I've tried installing ever version on Hyperion. NG using the script but it never starts up. When I run "systemctl status hyperion.service" I get this

hyperion.service - Hyperion ambient light systemd service
Loaded: loaded (/storage/.config/system.d/hyperion.service; enabled; vendor preset: disabled)
Active: activating (auto-restart) (Result: signal) since Wed 2020-09-09 21:22:50 UTC; 8s ago
Process: 418 ExecStart=/storage/hyperion/bin/hyperiond --userdata /storage/hyperion/ (code=killed, signal=ILL)
Main PID: 418 (code=killed, signal=ILL)

It never fully activates.

Any help would be great, Thanks

 

I'm not sure if I'm using the right method to download. I used both of these scripts
"wget -qO- https://git.io/JUvg7 | bash"

"wget -qO- https://git.io/JUvg7 | bash -s 2.0.0-alpha.(1-7)"

to download and everything seemed to go fine

Thanks for replying so fast btw

 

Yes I think so. I copied and the script as it is into putty and hit enter.

 

Sure give me a little bit to set it up again and I'll post a screen cap when I'm done

 

Ok fresh Libre 9.2.4 install. Connected to putty and ran "wget -qO- https://git.io/JUvg7 | bash -s 2.0.0-alpha.7" this was the outcome

 

( i know its not a good answer to your question, its just an advice
as "always" try alpha6, 7 wont work properly anyway (i had 7 on my pi zero and i ended up using alpha 6) )

 

Thanks, I have tried alpha.6 also but with the same results :/ Which version of Libre are you running?

 

I had the latest and one before that on my rpi zero + alpha 6 and worked perfectly.

Currently i have rpi4+latest+alpha6

 

@Paulchen-Panther
Warum funktioniert das nicht mehr? Ich wollte ein neues Pull Request installieren
Liegt das an der neusten LibreELEC Version?

LibreELEC:~ # wget -qO- https://git.io/JJr6Y | bash -s 1002
*******************************************************************************
This script will download a specific Pull Request Artifact from Hyperion.NG on LibreELEC
Created by Paulchen-Panther - hyperion-project.org - the official Hyperion source.