Hi, I'm stuck.It turns out that I have done all the configuration that touches on my Raspberry 4 I have installed the full noobs I have enabled SSH and SPI through sudo rapi-config and also dtparam = SPI = on.I have also installed the Hyperion alpha9 without any problem. And I have entered the web through port: 8090.
I leave you here how I have assembled all the Hardware.
And also the hyperion with its configuration. The led strip is the WD2801 and they are connected apparently well.
what type of ledstrip? You run on SPI i see, did you select the right protocol for your ledstrip?
can you provide a log from debug ? you find it in logs.
First you have to set your privilage into expert mode right corner WebUI
Sorry for my ignorance.I DO NOT see the logs.And my led strip is WD2801
you mean WS2801?
the logs is at WebUI:8090 at section [system] > logs, just click the debug button and copy paste
but first you have to set privilage in expert mode also on WebUI
Yes, sorry WS2801
But DEBUG its empty but if I change to WS281x do this.
2021-01-21T15:09:25.974Z [hyperiond LEDDEVICE] (INFO) Stopped LedDevice 'ws2801' 2021-01-21T15:09:25.976Z [hyperiond COMPONENTREG] (DEBUG) (ComponentRegister.cpp:36:setNewComponentState()) LED device: disabled 2021-01-21T15:09:25.977Z [hyperiond LEDDEVICE] (INFO) Start LedDevice 'ws281x'. 2021-01-21T15:09:25.977Z [hyperiond LEDDEVICE] (DEBUG) (LedDevice.cpp:148:init()) deviceConfig: [{"colorOrder":"rgb","currentLedCount":72,"dma":5,"gpio":18,"hardwareLedCount":72,"invert":false,"latchTime":0,"leds":256,"pwmchannel":0,"rewriteTime":1000,"rgbw":false,"type":"ws281x","whiteAlgorithm":"subtract_minimum"}] 2021-01-21T15:09:25.978Z [hyperiond LEDDEVICE] (DEBUG) (LedDevice.cpp:407:setLatchTime()) LatchTime updated to 0ms 2021-01-21T15:09:25.978Z [hyperiond LEDDEVICE] (DEBUG) (LedDevice.cpp:428:setRewriteTime()) Refresh interval = 1000ms 2021-01-21T15:09:25.978Z [hyperiond LEDDEVICE] (DEBUG) (LedDevice.cpp:434:setRewriteTime()) RewriteTime updated to 1000ms 2021-01-21T15:09:25.979Z [hyperiond LEDDEVICE] (DEBUG) (LedDeviceWS281x.cpp:59:init()) ws281x strip type : 1050624 2021-01-21T15:09:25.979Z [hyperiond LEDDEVICE] (ERROR) Device disabled, device 'ws281x' signals error: 'Failed to open. Error message: Hardware revision is not supported' 2021-01-21T15:09:26.003Z [hyperiond WEBSOCKET] (DEBUG) (JsonAPI.cpp:1063:handleLoggingCommand()) log streaming deactivated for client ::ffff:192.168.1.172 2021-01-21T15:09:36.419Z [hyperiond WEBSOCKET] (DEBUG) (JsonAPI.cpp:1054:handleLoggingCommand()) log streaming activated for client ::ffff:192.168.1.172 2021-01-21T15:09:36.433Z [hyperiond WEBSOCKET] (DEBUG) (JsonAPI.cpp:1063:handleLoggingCommand()) log streaming deactivated for client ::ffff:192.168.1.172 2021-01-21T15:11:28.289Z [hyperiond LEDDEVICE] (ERROR) Device disabled, device 'ws281x' signals error: 'Failed to open. Error message: Hardware revision is not supported' 2021-01-21T15:12:29.181Z [hyperiond WEBSOCKET] (DEBUG) (JsonAPI.cpp:1054:handleLoggingCommand()) log streaming activated for client ::ffff:192.168.1.172 2021-01-21T15:12:29.208Z [hyperiond WEBSOCKET] (DEBUG) (JsonAPI.cpp:1063:handleLoggingCommand()) log streaming deactivated for client ::ffff:192.168.1.172 2021-01-21T15:15:15.704Z [hyperiond WEBSOCKET] (DEBUG) (JsonAPI.cpp:1054:handleLoggingCommand()) log streaming activated for client ::ffff:192.168.1.172
you need NOT WS281x for your ledstrip, this is only for PWM.
you need RPI SPI ws2801
wrong GPIO, select first controller type for your ledstrip >> RPI SPI 2801 NOT ws281x
spi path, /dev/spivev0.0
I take this.
yes that's better 
set refresh time on 6000 and baudrate on 1500000
after this save and reboot your PI, then copy your debug log again
yes that's better
set refresh time on 6000 and baudrate on 1500000
after this save and reboot your PI
Okey i do it.
but no changes.
latchtime 1 ms
latchtime 1 ms
do it.
no changes 
settings is now correct, did you;
1, connect PIN19 to Data GPIO10
2, connect PIN23 to clock? GPIO11
3, ground your (-) from ledstrip and pi to PSU?
4, measure the voltage of PSU > may not exceed 5 volts
check al of this first >> https://pinout.xyz/pinout/spi
its too low, turn the white dial on PSU with care UP until 4,9 volts with load > ledstrip/PI connected
you have to measure directly on your PSU, also unwrap your strand of lights> i see that you purchased a strand of 5 mtr [is that right?] with 32l/mtr.
second, the best results will be there if you power the strand from BOTH sides
Now are 4.90
I think that the rapsberry does not send the information to the LEDs but i don't know why.
i meant 4.99 volts or 5.
how much watt is your PSU? and how much lights you have [want to light up?]
the data-arrow of the lights has to go AWAY from the PI
if you are 100% shure that all is connected in the right way then we look at the PI
Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!
