So, baudrate is correct now and for some reason some random LEDs are white now, I mean immediately after I plugged into power. Controlling still doesn´t work. As I saw the line "dtparam=spi=on" spi seems to be on so it should be the stripe which isn´t working. Just wrote an mail to the amazon vendor
LEDs lassen sich nicht steuern.
- videxx
- Erledigt
-
-
There's one thing you can do, check your settings in Hyperion if smoothing is off and see if this helps. You can do this with tab remote.
It's also possible to measure SPI activity on gpio pins with a test program.
Very weird because WS2801 is the easiest strip there is -
Where is this setting? What is tab remote?
Is there a program you can recommend?
Ik, that was the reason why i choose it. I will get a new on from the seller next week. -
Where is this setting? What is tab remote?
Is there a program you can recommend?
Ik, that was the reason why i choose it. I will get a new on from the seller next week.the setting is on [remote] tab at localip:8090, you can switch modules on or off here.
Smoothing was causing problems before so maybe this helps to disable and test again.its also possible your GPIO doesn't want to fire because there is something with authorisations on Hyperion which steers the GPIO outputs.
however i don't use Hyperbian so i don't know exactly if it sets the config by itself in every build. -
smothing is off
I think Hyperbian should work as its only job is to run Hyperion
I just installed Raspbian on another Raspberry and used python with code from a tuturial to try it out and it also didn´t work -
smothing is off
I think Hyperbian should work as its only job is to run Hyperion
I just installed Raspbian on another Raspberry and used python with code from a tuturial to try it out and it also didn´t workyes i think that too.
only thing you can do is measure GPIO output dataflow, i look up the schematics for you
-
Troubleshooting
Loopback test
This can be used to test SPI send and receive. Put a wire between MOSI and MISO. It does not test CE0 and CE1.wget https://raw.githubusercontent.…ntation/spi/spidev_test.c
gcc -o spidev_test spidev_test.c
./spidev_test -D /dev/spidev0.0
spi mode: 0
bits per word: 8
max speed: 500000 Hz (500 KHz)FF FF FF FF FF FF
40 00 00 00 00 95
FF FF FF FF FF FF
FF FF FF FF FF FF
FF FF FF FF FF FF
DE AD BE EF BA AD
F0 0Dexample of output after command, source https://www.raspberrypi.org/do…raspberrypi/spi/README.md
-
I will try it. So MOSI and MISO should be pin 19 and 23 on raspberry Pi3 right?
-
Oh its 19 and 21
-
btw;
did you run a few commands before installation in the terminal like
sudo apt-get update
sudo apt-get upgradesudo apt-get install git cmake build-essential qtbase5-dev libqt5serialport5-dev libqt5sql5-sqlite libqt5svg5-dev libqt5x11extras5-dev libusb-1.0-0-dev python3-dev libcec-dev libxcb-image0-dev libxcb-util0-dev libxcb-shm0-dev libxcb-render0-dev libxcb-randr0-dev libxrandr-dev libxrender-dev libavahi-core-dev libavahi-compat-libdnssd-dev libjpeg-dev libturbojpeg0-dev libssl-dev zlib1g-dev
sudo apt-get install libraspberrypi-dev -
I will try it. So MOSI and MISO should be pin 19 and 21 on raspberry Pi3 right?
yes they are, 19 and 21
-
btw;
did you run a few commands before installation in the terminal like
sudo apt-get update
sudo apt-get upgradesudo apt-get install git cmake build-essential qtbase5-dev libqt5serialport5-dev libqt5sql5-sqlite libqt5svg5-dev libqt5x11extras5-dev libusb-1.0-0-dev python3-dev libcec-dev libxcb-image0-dev libxcb-util0-dev libxcb-shm0-dev libxcb-render0-dev libxcb-randr0-dev libxrandr-dev libxrender-dev libavahi-core-dev libavahi-compat-libdnssd-dev libjpeg-dev libturbojpeg0-dev libssl-dev zlib1g-dev
sudo apt-get install libraspberrypi-dev
do you mean with the other raspberry? I didn´t do it for the Hyperbian one, I thought that all this stuff should be preinstalled -
do you mean with the other raspberry? I didn´t do it for the Hyperbian one, I thought that all this stuff should be preinstalled
do it anyway i would say, it can't do harm mate
-
-
did you connect the pins together? GPIO 9 and 10
-
did you connect the pins together? GPIO 9 and 10
yes -
something else is going on then, do the updates first its look like GPIO's isn't putting out anything also when hyperion isn't using GPIO output
-
The updates are running right now, shouldn´t take to long
-
-
they are working now, so now with Hyperion?
SPI GPIO MOSI to MISO is putting out and reading data.
so must work now with Hyperion we hope, or ledstrip is broke
Jetzt mitmachen!
Sie haben noch kein Benutzerkonto auf unserer Seite? Registrieren Sie sich kostenlos und nehmen Sie an unserer Community teil!