Beiträge von luckyjacks

  • Rpi3 + Arduino + libreELEC >> vendor preset: disabled

    Zitat von Lord-Grey

    Try Baudrate = 115200, You can later increase, if this one works.
    Plus ensure that the Logs with LED-DEVICE are included in the logs.
    You might want to disable the LED-Device via the "Remote Control" Screen and enable it again.
    This restarts the Led-Device and you should have logs to share....


    Ok, switched the Baudrate + turned of + on
    now seems to be a Log

  • Rpi3 + Arduino + libreELEC >> vendor preset: disabled

    Zitat von davieboy

    best thing you can do is post a proper debug log, without that no one may be able to help you - There should be more than 1 line, after you set it to debug.


    Screenshots of the LED Layout are no help, same with getting the status of Hyperion as its already running!


    Ok added the LED Controller Pics to the link
    https://www.dropbox.com/s/172g…17T21-01-27.087Z.png?dl=0
    this is so far everything from Debug, + the first debug was just these 2 lines, made me wonder 2

  • Rpi3 + Arduino + libreELEC >> vendor preset: disabled

    Zitat von davieboy

    enable debug logging in the dashboard, restart the process and see what errors appear


    my bad, on my dashboard I had no path with controller set to usb/adalight, What controller are you using?


    Maybe post some screens from your LED Hardware section so that others may be able to help


    Controller type is adalight

    Code
    2021-02-17T19:21:31.268Z [hyperiond WEBSOCKET] (DEBUG) (JsonAPI.cpp:1054:handleLoggingCommand()) log streaming activated for client ::ffff:192.168.1.41



    looks like that, because I turned the platform capture on manually before that

  • Rpi3 + Arduino + libreELEC >> vendor preset: disabled

    Zitat von davieboy

    no idea @luckyjacks you never really mentioned the LibreELEC setup in detail, If it was down to power not being sufficient and you were setup correctly i reckon you would see that reflect in the quality of the lighting but i suspect you have the old Hyperion addon installed while trying to setup Hyperion NG and or mixing old setup with the new setup.


    Ok, yes I had the old one installed most of the time, but always deactivated, when testing, but latly I always had the hyperion control running additionally,
    I deinstalled everything now, quoted, and rebooted..
    did the Isusb,

    Code
    LibreELEC:~ # lsusb
Bus 001 Device 005: ID 248a:8514 Maxxter
Bus 001 Device 004: ID 1a86:7523 QinHeng Electronics HL-340 USB-Serial adapter
Bus 001 Device 007: ID 534d:2109
Bus 001 Device 006: ID 046d:c52b Logitech, Inc. Unifying Receiver
Bus 001 Device 008: ID 0424:7800 Standard Microsystems Corp.
Bus 001 Device 003: ID 0424:2514 Standard Microsystems Corp. USB 2.0 Hub
Bus 001 Device 002: ID 0424:2514 Standard Microsystems Corp. USB 2.0 Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub


    then status after when Iput the output path back to /dev/ttyUSB0:



    the QinHeng Electronics HL-340 USB-Serial adapter, might be my arduino clone, that is connected for now..
    but no change, as far as I can tell..

  • Rpi3 + Arduino + libreELEC >> vendor preset: disabled


    Ok, thanks, i will try as well.
    But I also was thinking about, that it could have something to with LED being 60 per meter, rather then 30, becoming an Volt power issue somehow...

  • Rpi3 + Arduino + libreELEC >> vendor preset: disabled


    Ok, first of all thanks for the fast reply!
    I'll comment out those lines, off cause then. But am afraid it won't be possible to test the LEDs like that now,
    I haven't bought any GPIO Pin cables yet, since I was not sure if or how to detach the LEDs from the power plugs that are attached n all that.
    But I also got the feeling its not the LEDs that are root cause, since I did have them all together light up for a while already...
    And as long as I don't get Hyperion NG to really talk to Arduino, I think it does not matter..?

  • Rpi3 + Arduino + libreELEC >> vendor preset: disabled

    Hi,
    I am new to Hyperion and all that, ran into it cause I tried to get a China Led/Arduino setup, I bought on Ebay,
    to work with Libreelec, on Rpi 3B, after watching a Youtube Tut from a guy with the same Hardware setup.
    First I tried with the old Kodi Addon (with favorites on of switch, like on Youtube-tut),
    then with Hyperion.ng, but nothing worked.
    The China preset-up are 180 x WS2812B LED's + Arduino klone, + digital video grabber
    (which isn't yet important, since I can't even get the signals send from the KODI platform).
    I have the Original-Adalight-Sketch witch the FastLED Library, Baudrate 500000 and Pin 6 enabled.
    There shouldn't be an issue with my LED configuration, it took a little, but I think I can rule that out,
    since I actually had them light up white, all together, and staying that way...
    until I turned the Rpi of.


    When systemctl status hyperion.service --now
    First: dial out overwriting timeout text, niw I only get, [ vendor disabled ], Hyperion systemd service starts, but eventually nothing else happens.


    Code
    ● hyperion.service - Hyperion ambient light systemd service
Loaded: loaded (/storage/.config/system.d/hyperion.service; enabled; vendor preset: disabled)
Active: active (running) since Thu 2019-04-11 17:28:43 BST; 1 years 9 months ago
Main PID: 520 (hyperiond)
Memory: 57.8M
CGroup: /system.slice/hyperion.service
└─520 /storage/hyperion/bin/hyperiond --userdata /storage/hyperion/


Apr 11 17:28:43 LibreELEC systemd[1]: Started Hyperion ambient light systemd service


    Also I bought another UNO R3 ATmega328P Board from Eckstein, since I assumed, the issue was with the Arduino, but it turned out the same basically, other then, the new one addresses the de/ttyAMA0 port, and the Uno China Klone uses ttyUSB0. ( I also tried setting, on the console, the Output path to auto, or depending to AMA0 or USB0 .....)


    ..


    I tried installing the Raspbian-tool Addon, for KODI, to possibly activate the UART mini port, but did not find out how to run that really..


    Also tried editing config.txt and cmdline.txt via ssh




    and also cmdline:


    Code
    boot=LABEL=System disk=LABEL=Storage quiet


#dwc_otg.lpm_enable=0 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait


port = serial.Serial("/dev/dwc_otg.lpm_enable=0


console=tty1 console=serial0(or ttyAMA0),115200 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait


    so far I can tell that, the ttyUSB0 und AMA0 seems to active, from ls -l /dev/ttyUSB0 command...


    But still vendor disabeld???


    My Rainbow Swirl test also fails

    Code
    LibreELEC:~ # /storage/hyperion/bin/hyperion-remote -e "Rainbow Swirl" -a 192.168.1.36:8090
hyperion-remote:
        Version   : 2.0.0-alpha.9 ((HEAD detached at 83338dc3) (Paulchen Panther-ca50487e/83338dc3-1605733041))
        build time: Nov 18 2020 21:59:22
Connected to: "192.168.1.36:8090"
Start effect  "Rainbow Swirl"
Error while reading data from host



    and I tried a setup with Hyperbian as well, but then could not access the http://ipofyourpi:8090


    What did I get wrong? I seriously need some good advice on that, please!! :sickxx:


    [Und ja, ich hatte den Thread schon mal als offene Kommunikation gestartet, und zwei Wochen mit mir selbst geredet, ja ich bin auch neu was Foren angeht...Bitte erst helfen dann lachen :crying:]