Beiträge von Kisspachyousee

I had installed hyperion a few weeks ago on OrangePi pc plus, with OS ArmBian. it worked perfectly. one day all of a sudden he would stop leaving. so i tried to delete it and install all over again but it keeps giving me this error:

 * failed to open vchiq instance  Hyperion caught signal :SIGSEGV segmentation fault

EDIT: obviously immediately after I wrote I managed to solve, now the graphical interface is started, I gave this command:

hyperiond -d --deleteDatabase

I managed to get everything working!

I double checked the soldering, and I realized that the GND between the led power supply and the orange Pi was not well connected, but it was not enough. I removed the Smoothing and set Baudrate as 2400000.

also to enable the SPI correctly I set this in /boot/armbianEnv.txt:

overlays = analog-codec cir i2c0 spi-spidev uart1 usbhost2 usbhost3 w1-gpio
param_w1_pin = PA20
param_w1_pin_int_pullup = 1
param_uart1_rtscts = 1
param_spidev_spi_bus = 0

is it possible that i have this problem? Allwinner H3 and WS2801 - weird color switch every (un)even value

I meant Smoothing.

Zitat von Lighting-guy77

did you correct at leddevice choose the BGR/RGB option?

i think so, i put RGB but i also tried GRB. the LEDs flash and the colors also mingle at different baud rates. the same configuration with the raspberry 3 works perfectly. I tried some effects that are already installed, the only one you can see well is that of the police, where there are red and blue running

nothing to do, I changed the baudrate as you told me, but only the first LED remains on.

I have deactivated the gradient and now the LEDs light up. they flicker a lot less than before, but still there seems to be a lot of mixed colors. for example when I do the red green test, red alternates with blue, same thing with green.

the voltage was definitely high, from 5.18v I set it to 5v. the leds have stopped flickering, but they are not working properly. when I go to #conf_leds led settings, I select ws2801, Baudrate 1000000, spidev0.0, if I do "invert signal" they become all white, otherwise only the first led lights up.

yes I can adjust it. tomorrow I measure the voltage I try to adjust it. the LEDs are just over 3 meters

Thanks for your help!

I have a 5v 10A power supply to power the leds and also the orangepi. from the power supply I connected two USB female, with one I connect the LEDs, with the other the orangepi.

(gnd are not directly connected to each other, but use the same power supply)

they flash a lot and quickly, but it seems to perceive the correct colors between the flickers when I do the test with red and green.

these are the pins of the orange pi. they are not the same, but very similar.

Hello everybody,

i have a problem with the hyperion configuration.

I installed everything on a raspberry 3 b that a friend lent me, everything works fine using the ws2801 led and stk1160 as grabber.

I had tried with a raspberry 1 b + (2014) but it can't acquire the video from the grabber, I don't know exactly why.

I therefore thought of installing hyperion on OrangePi pc +. the problem is that by connecting the LEDs to pins 19 and 23, the LEDs flash and flicker continuously, whatever the image, even when I do BYTE RGB ORDER ASSISTANT. is there anything i miss when i connect with the gpio?

these are the settings I have enabled on armbianEnv.txt to enable spi

overlays = analog-codec cir i2c0 spi-spidev uart1 usbhost2 usbhost3 w1-gpio

param_w1_pin = PA20

param_w1_pin_int_pullup = 1

param_uart1_rtscts = 1

param_spidev_spi_bus = 0