Beiträge von Dennis Herrmann

eth0 Link encap:Ethernet Hardware Adresse b8:27:eb:4f:8a:49
inet Adresse:192.168.178.0 Bcast:192.168.178.255 Maske:255.255.255.0
inet6-Adresse: fe80::aa02:3832:7afb:9e0c/64 Gültigkeitsbereich:Verbindung
inet6-Adresse: 2a02:8108:11c0:6560:39c0:eb2a:25c9:905d/64 Gültigkeitsbereich:Global
UP BROADCAST RUNNING MULTICAST MTU:1500 Metrik:1
RX packets:79400 errors:0 dropped:1101 overruns:0 frame:0
TX packets:46870 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:1000
RX bytes:79809621 (76.1 MiB) TX bytes:6263620 (5.9 MiB)

lo Link encap:Lokale Schleife
inet Adresse:127.0.0.1 Maske:255.0.0.0
inet6-Adresse: ::1/128 Gültigkeitsbereich:Maschine
UP LOOPBACK RUNNING MTU:65536 Metrik:1
RX packets:581 errors:0 dropped:0 overruns:0 frame:0
TX packets:581 errors:0 dropped:0 overruns:0 carrier:0
Kollisionen:0 Sendewarteschlangenlänge:1
RX bytes:55195 (53.9 KiB) TX bytes:55195 (53.9 KiB)

i don't understand this.....Eathernet cable is in use, maybe the fritzbox has to be programmed?

--- google.com ping statistics ---
67 packets transmitted, 0 received, +61 errors, 100% packet loss, time 72668ms
pipe 5
if i type in what you said, nothing happened, than this:

root@raspberrypi:/home/pi# cd /tmp
root@raspberrypi:/tmp# wget -nv -N https://raw.github.com/hyperio…r/bin/install_hyperion.sh
root@raspberrypi:/tmp#

thanks...i got putty since yesterday so no problem.
ssh connected an terminal use no problem.
wget -nv -N https://raw.github.com/hyperio…r/bin/install_hyperion.sh does nothing, so i clicked the link, copied the content and command it.
a few seconds and many many scrolls in the terminal later there was "exit". i pressed enter and typed ls-a but also nothing happened.

Hi...
ok, thank you...
But how i told, i am newbie in this. So i understand not at all. There is too much information. How can is plit the command? it's just a click in hyperion to start the install.
and where can i see if the .sh file is downloaded?
i translate as good as i can the error message:

Removing ¬ ダ install_hyperion.sh¬ ワ ワ is not possible: file or directory not found

Hi there,
i am a absolutely german newbie, so please be gentle.
I got a PI3 with Jessie running.
SSH is enabled, time and date and so on is all ok.
Hyperion connected to my PI, but if i click on "inst/akt Hyperion" it takes a few seconds and i get an error.

SSH Traffic:
ssh connected
ssh out: cd /tmp && wget -nv -N https://raw.github.com/hyperio…r/bin/install_hyperion.sh && chmod +x install_hyperion.sh && sudo sh ./install_hyperion.sh HyperConInstall ; rm install_hyperion.sh
ssh out: rm: das Entfernen von ￢ﾀﾞinstall_hyperion.sh￢ﾀﾜ ist nicht mￃﾶglich: Datei oder Verzeichnis nicht gefunden

i tried to fix and understand it the whole night, but i didn't get it whats wrong.
i am online with ethernet, not wlan to be sure, the internet is ok...

Can someone please help me? i am absolutely newbie in this raspberry thing.

Thanks guys