any help on this
Posts by hatter456
-
-
# For more options and information see
# Some settings may impact device functionality. See link above for details
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
hdmi_force_hotplug=1
hdmi_force_edid_audio=1
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
dtparam=spi=on
core_freq=250
# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=off
disable snd_bcm2835
# Automatically load overlays for detected cameras
camera_auto_detect=1
# Automatically load overlays for detected DSI displays
display_auto_detect=1
# Enable DRM VC4 V3D driver
dtoverlay=vc4-kms-v3d
max_framebuffers=2
# Disable compensation for displays with overscan
disable_overscan=1
[cm4]
# Enable host mode on the 2711 built-in XHCI USB controller.
# This line should be removed if the legacy DWC2 controller is required
# (e.g. for USB device mode) or if USB support is not required.
otg_mode=1
[all]
hyperion set to ws281x and connected to gpio 18
ok so i changed it to gpio 13 and its started to work, only problem is it starts to freak out .. goes intolike dance mode then works then dance etc.
-
can anyone help me out with how to check programing code. i have tried on multiple sd cards. a pi 4 and pi 3. I have downloaded hyperbian on one card i tried using ras pi os with install of hyperion and followed different videos and post , nothing has worked yet. been at this for a week now. i am a super noob at programing and have a bit of knowledge when it comes to circuits. my led strip is ws2815 12 volt leds. 12v 8a power supply which is over the amperage required for this strip. i have also installed logic level board in the setup. capture device is working. i can see it when i log into the ip address on hyperion . i configured hyperion to my setup unless there is something on it thats blocking the lights. im getting frustrated . i have entered "sudo updateHyperionUser -u root" and checked config.txt for dtparam=audio=off please help
-
i have pi on, attached to a screen, can access the terminal but how do i enter that code into it
ok i found the config and that code is already in there
have foud out if i unplug the ground from pi to led strip i get 13 leds that lite up white but are not controlable
-
how do i enter that in the code . im new at this coding
thanks
-
can you help me with this im new at coding and have no clue how to add any of that
nothing is working
-
im having pretty much the same issue as yael was . im am a complete noob to pi programing. i have been messing with electronics and wiring for years but im lost as hell right now. i am using pi3, ws2815 12volt led strip. i have followed videos and tuttorials on how to set everything up. been looking into this for a week now and i can not get the leds to light