Hey, i've seen there was a thread live on this in 2016 so not sure if it's changed. I'm wondering if i could schedule Hyperion to not come on during daylight hours, and have some sort of scheduler attached.
As an aside, big thanks to pclin who helped get my set up going. Awesome software, and super friendly support for often daft questions.
5v 2.1amp it's a usb plug and it's about 110 LEDS
So I looked at the wiring and embarrassingly one of the cables had come loose. After plugging it in, the device was connected to wled for about 15-20 seconds before then disconnecting.
I rechecked and everything is still plugged in and connected. It's very odd.
I had it set up to lights.local as well as the IP but neither are working.
If i'm really quick i manage to get to the port selected when flashing and it starts to load before saying
There is another application using the serial port. Even if i turn off the wifi the board keeps defaulting to the red lights and is unresponsive.
I genuinely think i've just got a broken board. The problem is if i order another i want to make sure whatever settings i changed wouldn't do this to another board.
So plugged them back in and nope i can't seem to get to WLED at all. I've also tried plugging back into my laptop to reflash and it shows up as a device in WLED for a micro second. I haven't changed the DNS for WLED.
Following your hyperion instructons i can see this in the log:
2023-04-24T17:40:45.413Z [LEDDEVICE|First LED Hardware instance] (ERROR) Cannot resolve mDNS hostname for given service [lights._wled._tcp.local]!2023-04-24T19:01:45.283Z [LEDDEVICE] (ERROR) Resolved mDNS hostname [lights.local.] timed out2023-04-24T19:02:33.440Z [WEBSOCKET] (DEBUG) (WebSocketClient.cpp:213:sendClose()) Send close to ::ffff:192.168.1.68: 1000 2023-04-24T19:02:34.024Z [WEBSOCKET] (DEBUG) (WebSocketClient.cpp:30:WebSocketClient()) New connection from ::ffff:192.168.1.682023-04-24T19:02:34.233Z [WEBSOCKET] (DEBUG) (JsonAPI.cpp:149:handleInstanceSwitch()) Client '::ffff:192.168.1.68' switch to Hyperion instance 02023-04-24T19:02:34.535Z [WEBSOCKET] (DEBUG) (JsonAPI.cpp:1220:handleLoggingCommand()) log streaming activated for client ::ffff:192.168.1.68
pclin - Ok i had everything up and working and it was great. I then went into wled looking to increase brightness clicked override once, upped the brightness and removed the power limiter. However now i can't seem to connect to WLED at all. Even plugging this back into my laptop to reflash makes the device pop up for about a second. Lights go to orange for a second and then move to i think the last colour they were on (red).
Not sure how to progress and hope i haven't fried my board.
Ah brill! Ok this makes all the sense i'll give it a go and report back.
Yep WLED is all configured and i can successfully control the LEDS
Hmm i guess my hyperion on the LG doesn't fully look like the interface you've posted on the left there. It has a black window saying:
Service Elevated: Yes
Daemon Running: Yes
Daemon Version -- Version info... etc etc
Autostart - set to true
Start
Stop
Reboot System
the result at the bottom says Daemon Started
So PicCap should have the IP address of my WLED instance ?
Again thanks for the help buddy 
this is going to be awesome and i can feel i'm close
Hey guys,
As the title says, i've got my WLED lights all set up. I've installed PicCap and Hyperion to my TV everything seems to be running. I've also installed Hyperion to my laptop and configured the lights around the TV. I'm now though at the point where i'm looking at how do i actually get all of these things talking to each other.
Apologies if i've missed something in a guide.
All help is really appreciated,
Awesome yep i do run LE11 - However i've actually rooted my webos tv so i was thinking i connect my esp to that instead.
I'll checkout your board and pray i get the same results over wifi.
Ok slowly and surely getting there. Think this would do the trick for an ESP32 board? Wt32-eth01 Embedded Serial Port Networking Bluetooth-compatible Ethernet Wifi Combo Gateway Mcu Esp32 Wireless Module Wt32 Eth01 - Integrated Circuits - AliExpress
Once i've got my light strip and this i'm going to need a way to power the ESP32? Is that direct or do i connect it to an arduino ?
Lastly, how does hyperion picap actually connect to this ESP32 board, is it just over a network? I thought there'd be a direct connection
Again thanks for all the help so far!
Yep i also don't get great coverage for my full 55' so i've gone and purchased BTF LIGHTING Individually Addressable Flexible Non Waterproof
For the controller i do have some old Arduino nanos kicking about https://www.amazon.co.uk/gp/product/B072BMYZ18?tag=hyperioforum-21&ie=UTF8&psc=1 i'm not sure though if these are compatible?
Just looking at the 2m lights i've got now they're powered by USB?
If not i'll start googling some compatible light strips to give a test
If i bought and LED strip with WLED already installed that could be my complete set up ?
Here are my lights https://www.amazon.co.uk/gp/product/B097TH15VZ?tag=hyperioforum-21&ie=UTF8&th=1
Just done a little googling and think i could have a completely no solder solution here if i found a WLED setup taking USB light input and having USB power
I've got a current LED strip of static colours that i power using one of the USB ports on the LG so would be hoping to use the same here.
Hey all,
Super excited to get this set up. I've got a rooted LG C9 that i've installed hyperion and PiCap on. I'm wondering though given i run LIbreelec on an Intel NUC whether i could get away without having to get a pi/capture card? Essentially i'm still at the stage of just working out what minimal equipment i can use to get this running. Looks awesome.
