Honestly, not a clue... It's a Lightberry, didn't build it myself. :unsure:
But if it could be hardware based, why don't I have problems with my 'older' install of OSMC?
Beiträge von Fire69
-
-
Ok, so I installed a new OSMC without Hyperion. Result, first 1 or 2 leds turn on after some time. After a couple of hours, the entire right side of my tv was lit white/blue.
So definitely not a Hyperion problem...I'm going over to the OSMC forum to ask what could be causing this.
-
Pryxus, I forgot to ask you, what hardware are you using for your leds?
I'm using a Lightberry, this thing already has a tendency to light up some leds when it doesn't get a signal (Pi powered off, etc...) -
I'm going to do a new install of OSMC now, and not install Hyperion for a day or 2, to check if the leds stay off.
After that, I'm going to install Hyperion and again check what the leds do. If they turn on, it has to be Hyperion, right?Hm, something I just thought of... When you install Hyperion, it enables SPI in the config.txt. Could it be that in the newer versions of OSMC/OpenElec (same kernel or something) there is a bug that sends unwanted data to the GPIO-pins?
-
You assumed correctly, that is exactly my problem (except my color is more blueish white, depends on the leds I suppose).
Very annoying indeed. I had a working install, but my SD got corrupt so I did a new OSMC/Hyperion install on a new card and then my problems started.
I got 'lucky' now, I was able to clone my corrupt card to a new SD and my old installation is working again now.But since we're having the same problem, and I also had the problem when I installed OpenElec as a test, I do think it's a Hyperion problem.
Why do you think it's not? -
OpenElec gaf hetzelfde probleem...
Het is me ondertussen gelukt om mijn oude werkende install van OSMC in orde te krijgen.
Ik heb gewoon een dd van de defecte SD (die blijkbaar vast zat in een soort van read-only mode) naar een nieuwe SD.
Alles werkte toen terug als een zonnetje. OSMC en Hyperion deden het beiden terug netjes.Maar als test heb ik toch maar even via HyperCon een update gedaan van Hyperion (waarbij het script nu wel correct werkte)
Resultaat => Nog geen 10min later sprongen led 0 en 1 terug aan op blauw/witEr lijkt me dus toch iets verkeerd te gaan in nieuwere versies van Hyperion...
-
Rasplex draait Plex ipv Kodi toch?
OpenElec is ook al niet zo'n goeie start...Code
Alles anzeigenssh connected ssh out: cd /tmp && wget -nv -N https://raw.github.com/hyperion-project/hyperion/master/bin/install_hyperion.sh && chmod +x install_hyperion.sh && sudo sh ./install_hyperion.sh HyperConInstall ; rm install_hyperion.sh ssh out: wget: invalid option -- 'n' ssh out: BusyBox v1.24.1 (2016-02-29 21:05:41 CET) multi-call binary. ssh out: Usage: wget [-c|--continue] [-s|--spider] [-q|--quiet] [-O|--output-document FILE] ssh out: [--header 'header: value'] [-Y|--proxy on/off] [-P DIR] ssh out: [-U|--user-agent AGENT] [-T SEC] URL... ssh out: Retrieve files via HTTP or FTP ssh out: -s Spider mode - only check file existence ssh out: -c Continue retrieval of aborted transfer ssh out: -q Quiet ssh out: -P DIR Save to DIR (default .) ssh out: -T SEC Network read timeout is SEC seconds ssh out: -O FILE Save to FILE ('-' for stdout) ssh out: -U STR Use STR for User-Agent header ssh out: -Y Use proxy ('on' or 'off') ssh out: rm: can't remove 'install_hyperion.sh': No such file or directory
Heb de install ook manueel moeten doen, nu testen wat de leds doen...
-
Ik denk dat deze thread wel dicht kan, het probleem ligt volgens mij niet aan Hyperion maar aan... OSMC of zo gok ik.
Gisteren kwam ik thuis en de helft van mijn leds branden wit/blauw. Ik was het lichtjes (pun intended :bigsmile:) beu aan het worden en heb toen de leds uitgezet via de remote an daarna de Hyperion-service gestopt.
Toen ik vanmorgen beneden kwam brannde terug een ganse hoop leds! M.a.w. het probleem kan niet bij Hyperion liggen.
Waarschijnlijk is er in een recente update van OSMC ergens iets dat misgaat (schrijven naar SPI of zo), dus ik zal op hun forum mijn licht even gaan opsteken... -
Aha, dan zal ik vanavond de addon eens installeren. Die werkt nu dus wel op een Rpi?
Hopelijk lost dat het probleem met de leds op.Maak ik een issue op github voor de installatieproblemen vanuit Hypercon?
-
Ik gebruik helemaal geen addon in Kodi :bigsmile:
Da's toch ook niet nodig dacht ik?ZitatNote that this plugin will not work for Kodi running on the Raspberry Pi
Het script werkt zonder problemen als ik het manueel in een terminal start, dus de deps zijn waarschijnlijk wel ok.
Vreemd dat het uit hypercon problemen geeft, het is in de basis exact dezelfde werkwijze... -
Ik kreeg het van dat gesukkel op mijn zenuwen en ben van nul herbegonnen.
OSMC opnieuw op kaartje geschreven. Updates geïnstalleerd en dan via Hypercon hyperion proberen installeren.
Zoals ik in mijn startpost al zei, dat gaat dus niet van een leien dakje...Hele hoop problemen met het installeren van de dependencies!
Code
Alles anzeigenssh connected ssh out: cd /tmp && wget -nv -N https://raw.github.com/hyperion-project/hyperion/master/bin/install_hyperion.sh && chmod +x install_hyperion.sh && sudo sh ./install_hyperion.sh HyperConInstall ; rm install_hyperion.sh ssh out: Last-modified header missing -- time-stamps turned off. ssh out: 2016-06-13 22:36:59 URL:https://raw.githubusercontent.com/hyperion-project/hyperion/master/bin/install_hyperion.sh [14472/14472] -> "install_hyperion.sh" [1] ssh in: ******************************************************************************* ssh in: This script will install/update Hyperion Ambient Light ssh in: Created by brindosch - hyperion-project.org - the official Hyperion source. ssh in: ******************************************************************************* ssh in: ---> Stop Hyperion, if necessary ssh in: ---> Install/Update Hyperion dependencies (This may take a while) ssh out: debconf: unable to initialize frontend: Dialog ssh out: debconf: (Dialog frontend will not work on a dumb terminal, an emacs shell buffer, or without a controlling terminal.) ssh out: debconf: falling back to frontend: Readline ssh out: debconf: unable to initialize frontend: Readline ssh out: debconf: (Can't locate Term/ReadLine.pm in @INC (you may need to install the Term::ReadLine module) (@INC contains: /etc/perl /usr/local/lib/arm-linux-gnueabihf/perl/5.20.2 /usr/local/share/perl/5.20.2 /usr/lib/arm-linux-gnueabihf/perl5/5.20 /usr/share/perl5 /usr/lib/arm-linux-gnueabihf/perl/5.20 /usr/share/perl/5.20 /usr/local/lib/site_perl .) at /usr/share/perl5/Debconf/FrontEnd/Readline.pm line 7, <> line 21.) ssh out: debconf: falling back to frontend: Teletype ssh out: dpkg-preconfigure: unable to re-open stdin: ssh in: Selecting previously unselected package fontconfig. ssh in: (Reading database ... ssh in: (Reading database ... 5% ssh in: (Reading database ... 10% ssh in: (Reading database ... 15% ssh in: (Reading database ... 20% ssh in: (Reading database ... 25% ssh in: (Reading database ... 30% ssh in: (Reading database ... 35% ssh in: (Reading database ... 40% ssh in: (Reading database ... 45% ssh in: (Reading database ... 50% ssh in: (Reading database ... 55% ssh in: (Reading database ... 60% ssh in: (Reading database ... 65% ssh in: (Reading database ... 70% ssh in: (Reading database ... 75% ssh in: (Reading database ... 80% ssh in: (Reading database ... 85% ssh in: (Reading database ... 90% ssh in: (Reading database ... 95% ssh in: (Reading database ... 100% ssh in: (Reading database ... 22348 files and directories currently installed.) ssh in: Preparing to unpack .../fontconfig_2.11.0-6.3_armhf.deb ... ssh in: Unpacking fontconfig (2.11.0-6.3) ... ssh in: Selecting previously unselected package libxau6:armhf. ssh in: Preparing to unpack .../libxau6_1%3a1.0.8-1_armhf.deb ... ssh in: Unpacking libxau6:armhf (1:1.0.8-1) ... ssh in: Selecting previously unselected package x11-common. ssh in: Preparing to unpack .../x11-common_1%3a7.7+7_all.deb ... ssh in: Unpacking x11-common (1:7.7+7) ... ssh in: Selecting previously unselected package libice6:armhf. ssh in: Preparing to unpack .../libice6_2%3a1.0.9-1+b1_armhf.deb ... ssh in: Unpacking libice6:armhf (2:1.0.9-1+b1) ... ssh in: Selecting previously unselected package libsm6:armhf. ssh in: Preparing to unpack .../libsm6_2%3a1.2.2-1+b1_armhf.deb ... ssh in: Unpacking libsm6:armhf (2:1.2.2-1+b1) ... ssh in: Selecting previously unselected package libxdmcp6:armhf. ssh in: Preparing to unpack .../libxdmcp6_1%3a1.1.1-1+b1_armhf.deb ... ssh in: Unpacking libxdmcp6:armhf (1:1.1.1-1+b1) ... ssh in: Selecting previously unselected package libxcb1:armhf. ssh in: Preparing to unpack .../libxcb1_1.10-3+b1_armhf.deb ... ssh in: Unpacking libxcb1:armhf (1.10-3+b1) ... ssh in: Selecting previously unselected package libx11-data. ssh in: Preparing to unpack .../libx11-data_2%3a1.6.2-3_all.deb ... ssh in: Unpacking libx11-data (2:1.6.2-3) ... ssh in: Selecting previously unselected package libx11-6:armhf. ssh in: Preparing to unpack .../libx11-6_2%3a1.6.2-3_armhf.deb ... ssh in: Unpacking libx11-6:armhf (2:1.6.2-3) ... ssh in: Selecting previously unselected package libxt6:armhf. ssh in: Preparing to unpack .../libxt6_1%3a1.1.4-1+b1_armhf.deb ... ssh in: Unpacking libxt6:armhf (1:1.1.4-1+b1) ... ssh in: Selecting previously unselected package libaudio2:armhf. ssh in: Preparing to unpack .../libaudio2_1.9.4-3_armhf.deb ... ssh in: Unpacking libaudio2:armhf (1.9.4-3) ... ssh in: Selecting previously unselected package libmng1:armhf. ssh in: Preparing to unpack .../libmng1_1.0.10+dfsg-3.1+b3_armhf.deb ... ssh in: Unpacking libmng1:armhf (1.0.10+dfsg-3.1+b3) ... ssh in: Selecting previously unselected package qtcore4-l10n. ssh in: Preparing to unpack .../qtcore4-l10n_4%3a4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1_all.deb ... ssh in: Unpacking qtcore4-l10n (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1) ... ssh in: Selecting previously unselected package libqtcore4:armhf. ssh in: Preparing to unpack .../libqtcore4_4%3a4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1_armhf.deb ... ssh in: Unpacking libqtcore4:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1) ... ssh in: Selecting previously unselected package libqt4-xml:armhf. ssh in: Preparing to unpack .../libqt4-xml_4%3a4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1_armhf.deb ... ssh in: Unpacking libqt4-xml:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1) ... ssh in: Selecting previously unselected package libqtdbus4:armhf. ssh in: Preparing to unpack .../libqtdbus4_4%3a4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1_armhf.deb ... ssh in: Unpacking libqtdbus4:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1) ... ssh in: Selecting previously unselected package libqt4-network:armhf. ssh in: Preparing to unpack .../libqt4-network_4%3a4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1_armhf.deb ... ssh in: Unpacking libqt4-network:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1) ... ssh in: Selecting previously unselected package libxext6:armhf. ssh in: Preparing to unpack .../libxext6_2%3a1.3.3-1_armhf.deb ... ssh in: Unpacking libxext6:armhf (2:1.3.3-1) ... ssh in: Selecting previously unselected package libxrender1:armhf. ssh in: Preparing to unpack .../libxrender1_1%3a0.9.8-1+b1_armhf.deb ... ssh in: Unpacking libxrender1:armhf (1:0.9.8-1+b1) ... ssh in: Selecting previously unselected package libqtgui4:armhf. ssh in: Preparing to unpack .../libqtgui4_4%3a4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1_armhf.deb ... ssh in: Unpacking libqtgui4:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1) ... ssh in: Selecting previously unselected package libusb-1.0-0:armhf. ssh in: Preparing to unpack .../libusb-1.0-0_2%3a1.0.19-1_armhf.deb ... ssh in: Unpacking libusb-1.0-0:armhf (2:1.0.19-1) ... ssh in: Processing triggers for systemd (215-17+deb8u4) ... ssh in: Setting up fontconfig (2.11.0-6.3) ... ssh in: Regenerating fonts cache... done. ssh in: Setting up libxau6:armhf (1:1.0.8-1) ... ssh in: Setting up x11-common (1:7.7+7) ... ssh in: debconf: unable to initialize frontend: Dialog ssh in: debconf: (Dialog frontend will not work on a dumb terminal, an emacs shell buffer, or without a controlling terminal.) ssh in: debconf: falling back to frontend: Readline ssh in: debconf: unable to initialize frontend: Readline ssh in: debconf: (Can't locate Term/ReadLine.pm in @INC (you may need to install the Term::ReadLine module) (@INC contains: /etc/perl /usr/local/lib/arm-linux-gnueabihf/perl/5.20.2 /usr/local/share/perl/5.20.2 /usr/lib/arm-linux-gnueabihf/perl5/5.20 /usr/share/perl5 /usr/lib/arm-linux-gnueabihf/perl/5.20 /usr/share/perl/5.20 /usr/local/lib/site_perl .) at /usr/share/perl5/Debconf/FrontEnd/Readline.pm line 7.) ssh in: debconf: falling back to frontend: Teletype ssh in: /var/lib/dpkg/info/x11-common.postinst: 697: /var/lib/dpkg/info/x11-common.postinst: update-rc.d: not found ssh in: dpkg: error processing package x11-common (--configure): ssh in: subprocess installed post-installation script returned error exit status 127 ssh in: dpkg: dependency problems prevent configuration of libice6:armhf: ssh in: libice6:armhf depends on x11-common; however: ssh in: Package x11-common is not configured yet. ssh in: dpkg: error processing package libice6:armhf (--configure): ssh in: dependency problems - leaving unconfigured ssh in: dpkg: dependency problems prevent configuration of libsm6:armhf: ssh in: libsm6:armhf depends on libice6 (>= 1:1.0.0); however: ssh in: Package libice6:armhf is not configured yet. ssh in: dpkg: error processing package libsm6:armhf (--configure): ssh in: dependency problems - leaving unconfigured ssh in: Setting up libxdmcp6:armhf (1:1.1.1-1+b1) ... ssh in: Setting up libxcb1:armhf (1.10-3+b1) ... ssh in: Setting up libx11-data (2:1.6.2-3) ... ssh in: Setting up libx11-6:armhf (2:1.6.2-3) ... ssh in: dpkg: dependency problems prevent configuration of libxt6:armhf: ssh in: libxt6:armhf depends on libice6 (>= 1:1.0.0); however: ssh in: Package libice6:armhf is not configured yet. ssh in: libxt6:armhf depends on libsm6; however: ssh in: Package libsm6:armhf is not configured yet. ssh in: dpkg: error processing package libxt6:armhf (--configure): ssh in: dependency problems - leaving unconfigured ssh in: dpkg: dependency problems prevent configuration of libaudio2:armhf: ssh in: libaudio2:armhf depends on libxt6; however: ssh in: Package libxt6:armhf is not configured yet. ssh in: dpkg: error processing package libaudio2:armhf (--configure): ssh in: dependency problems - leaving unconfigured ssh in: Setting up libmng1:armhf (1.0.10+dfsg-3.1+b3) ... ssh in: Setting up qtcore4-l10n (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1) ... ssh in: Setting up libqtcore4:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1) ... ssh in: Setting up libqt4-xml:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1) ... ssh in: Setting up libqtdbus4:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1) ... ssh in: Setting up libqt4-network:armhf (4:4.8.6+git64-g5dc8b2b+dfsg-3+deb8u1) ... ssh in: Setting up libxext6:armhf (2:1.3.3-1) ... ssh in: Setting up libxrender1:armhf (1:0.9.8-1+b1) ... ssh in: dpkg: dependency problems prevent configuration of libqtgui4:armhf: ssh in: libqtgui4:armhf depends on libaudio2; however: ssh in: Package libaudio2:armhf is not configured yet. ssh in: libqtgui4:armhf depends on libice6 (>= 1:1.0.0); however: ssh in: Package libice6:armhf is not configured yet. ssh in: libqtgui4:armhf depends on libsm6; however: ssh in: Package libsm6:armhf is not configured yet. ssh in: dpkg: error processing package libqtgui4:armhf (--configure): ssh in: dependency problems - leaving unconfigured ssh in: Setting up libusb-1.0-0:armhf (2:1.0.19-1) ... ssh in: Processing triggers for libc-bin (2.19-18+deb8u4) ... ssh in: Processing triggers for systemd (215-17+deb8u4) ... ssh in: Errors were encountered while processing: ssh in: x11-common ssh in: libice6:armhf ssh in: libsm6:armhf ssh in: libxt6:armhf ssh in: libaudio2:armhf ssh in: libqtgui4:armhf ssh out: E: Sub-process /usr/bin/dpkg returned an error code (1) ssh in: ---> Raspberry Pi found, but SPI is not set, we write "dtparam=spi=on" to /boot/config.txt ssh in: ---> Downloading the appropriate Hyperion release ssh out: 2016-06-13 22:38:48 URL:http://tenet.dl.sourceforge.net/project/hyperion-project/release/hyperion_rpi2_osmc.tar.gz [1636414/1636414] -> "-" [1] ssh in: ---> Installing systemd script ssh in: ---> Modify systemd script for OSMC usage ssh in: ---> Starting Hyperion ssh in: ******************************************************************************* ssh in: Hyperion Installation/Update finished! ssh in: Please download the latest HyperCon version to benefit from new features! ssh in: To create a config, follow the HyperCon Guide at our Wiki (EN/DE)! ssh in: Wiki: wiki.hyperion-project.org Webpage: www.hyperion-project.org ssh in: ******************************************************************************* ssh in: Rebooting now, we added dtparam=spi=on to config.txtAls ik:
Codecd /tmp && wget -nv -N https://raw.github.com/hyperion-project/hyperion/master/bin/install_hyperion.sh && chmod +x install_hyperion.sh && sudo sh ./install_hyperion.sh HyperConInstall ; rm install_hyperion.sh
opsplits en manueel via ssh doe, lukt het wel zonder alle errors. Ik gebruik dan wel de HyperConInstall optie niet erbij. Waarvoor dient deze juist? Kan dat het verschil maken?Ik heb de grabber in de config laten staan, momenteel blijven de leds nog uit, ik check morgenvroeg of dat nog zo is...
Probleem met de app heb ik gevonden. Mijn priority stond nog op 1100. Dat was ooit de standaard prioriteit dacht ik van hyperion zelf. Daarom had ik deze in de app ook zo ingesteld zodat ik via de app een override kon doen.
Wat is de standaard priority nu als je een film afspeelt?
Het is handig als ik de leds dan kan uitzetten als ik via mijn projector kijk zodat er geen licht vanachter mijn projectiescherm komt.Sorry voor de lap tekst en de vele vragen. Hopelijk zijn de errors (en mijn vragen) voor jullie ook interessant.
-
Nou, 2 problemen...
1. Ik heb de framegrabber uitgezet. Als ik nu een film speel doen de leds helemaal niks meer. Zet ik hem terug aan, werkt het wel.2. Plots werkt ook de android app niet meer (met of zonder grabber). Connectie is ok, de app zegt 'server synchronised' en ik krijg bvb. ook de lijst van effects te zien, maar de leds doen niks meer
Gisteren werkte de app gewoon, dus snap niet goed wat er aan de hand is. Service gerestart, rpi gerestart, geen effect...[edit]
Ik heb er even mijn oude sd'tje terug ingestoken, daar werkt alles nog steeds netjes zoals het hoort.
(behalve dat door de corruptie geen wijzigingen aan het filesystem worden opgeslaan...) -
Die framegrabber heb ik eigenlijk niet nodig dan?
Ik zal het even aanpassen en vanavond testen (kan de leds moeilijk checken vanop m'n werk ;))Thanks!
-
Hallo,
Ik heb gisteren mij OSMC moeten herinstalleren vanwege SD-corruptie.
Voor de eerste keer de installatie via HyperCon gedaan (ging niet van een leien dakje) maar het draait nu terug allemaal.
Enkel heb ik het probleem dat 1 of 2 leds steeds terug aangaan in wit of blauw na een tijdje als er niks gespeeld wordt in Kodi.
Als ik dan een film start/stop of via de Android-app een kleur zet en clear is het ok, maar na een tijdje gaan de leds terug aan.
Voor de reinstall had ik dit probleem niet. Ja, toch wel, maar enkel als ik de raspberry van de stroom haalde, da's een gekend probleem van Lightberry.Dit is mijn (nieuw aangemaakte) config. Ik heb nog niet getest met mijn oude config file, die ziet er toch wel redelijk anders uit...
[edit]
Was ik nog vergeten. Vroeger kon ik bij hardware uit het lijstje LightBerry kiezen, die staat er nu niet meer tussen; Ik heb WS2801 gekozen, volgens hun site is dit ook OK?Code
Alles anzeigen// Automatically generated configuration file for Hyperion ambilight daemon // Notice: All values are explained with comments at our wiki: wiki.hyperion-project.org (config area) // Generated by: HyperCon (The Hyperion deamon configuration file builder) // Created with HyperCon V1.03.1 (11.06.2016) { // DEVICE CONFIGURATION "device" : { "name" : "MyHyperionConfig", "type" : "ws2801", "output" : "/dev/spidev0.0", "rate" : 500000, "colorOrder" : "rgb" }, // COLOR CALIBRATION CONFIG "color" : { "channelAdjustment" : [ { "id" : "default", "leds" : "*", "pureRed" : { "redChannel" : 255, "greenChannel" : 0, "blueChannel" : 0 }, "pureGreen" : { "redChannel" : 0, "greenChannel" : 255, "blueChannel" : 0 }, "pureBlue" : { "redChannel" : 0, "greenChannel" : 0, "blueChannel" : 255 } } ], "temperature" : [ { "id" : "default", "leds" : "*", "correctionValues" : { "red" : 255, "green" : 255, "blue" : 255 } } ], "transform" : [ { "id" : "default", "leds" : "*", "hsl" : { "saturationGain" : 1.0000, "luminanceGain" : 1.0000, "luminanceMinimum" : 0.0000 }, "red" : { "threshold" : 0.0000, "gamma" : 2.5000 }, "green" : { "threshold" : 0.0000, "gamma" : 2.5000 }, "blue" : { "threshold" : 0.0000, "gamma" : 2.5000 } } ], // SMOOTHING CONFIG "smoothing" : { "type" : "linear", "time_ms" : 200, "updateFrequency" : 20.0000, "updateDelay" : 0 } }, // NO V4L2 GRABBER CONFIG // FRAME GRABBER CONFIG "framegrabber" : { "width" : 64, "height" : 64, "frequency_Hz" : 10.0, "priority" : 890 }, // BLACKBORDER CONFIG "blackborderdetector" : { "enable" : true, "threshold" : 0.0, "unknownFrameCnt" : 600, "borderFrameCnt" : 50, "maxInconsistentCnt" : 10, "blurRemoveCnt" : 1, "mode" : "default" }, // KODI CHECK CONFIG "xbmcVideoChecker" : { "xbmcAddress" : "127.0.0.1", "xbmcTcpPort" : 9090, "grabVideo" : true, "grabPictures" : true, "grabAudio" : true, "grabMenu" : false, "grabPause" : false, "grabScreensaver" : false, "enable3DDetection" : true }, // BOOTEFFECT CONFIG "bootsequence" : { "color" : [0,0,0], "effect" : "Rainbow swirl fast", "duration_ms" : 3000, "priority" : 700 }, // JSON SERVER CONFIG "jsonServer" : { "port" : 19444 }, // PROTO SERVER CONFIG "protoServer" : { "port" : 19445 }, // EFFECT PATH "effects" : { "paths" : [ "/storage/hyperion/effects", "/usr/share/hyperion/effects" ] }, // NO BOBLIGHT SERVER CONFIG // NO JSON/PROTO FORWARD CONFIG // LED CONFIGURATION "leds" : [ { "index" : 0, "hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 }, "vscan" : { "minimum" : 0.8750, "maximum" : 1.0000 } }, { "index" : 1, "hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 }, "vscan" : { "minimum" : 0.7500, "maximum" : 0.8750 } }, { "index" : 2, "hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 }, "vscan" : { "minimum" : 0.6250, "maximum" : 0.7500 } }, { "index" : 3, "hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 }, "vscan" : { "minimum" : 0.5000, "maximum" : 0.6250 } }, { "index" : 4, "hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 }, "vscan" : { "minimum" : 0.3750, "maximum" : 0.5000 } }, { "index" : 5, "hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 }, "vscan" : { "minimum" : 0.2500, "maximum" : 0.3750 } }, { "index" : 6, "hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 }, "vscan" : { "minimum" : 0.1250, "maximum" : 0.2500 } }, { "index" : 7, "hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 }, "vscan" : { "minimum" : 0.0000, "maximum" : 0.1250 } }, { "index" : 8, "hscan" : { "minimum" : 0.9286, "maximum" : 1.0000 }, "vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 } }, { "index" : 9, "hscan" : { "minimum" : 0.8571, "maximum" : 0.9286 }, "vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 } }, { "index" : 10, "hscan" : { "minimum" : 0.7857, "maximum" : 0.8571 }, "vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 } }, { "index" : 11, "hscan" : { "minimum" : 0.7143, "maximum" : 0.7857 }, "vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 } }, { "index" : 12, "hscan" : { "minimum" : 0.6429, "maximum" : 0.7143 }, "vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 } }, { "index" : 13, "hscan" : { "minimum" : 0.5714, "maximum" : 0.6429 }, "vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 } }, { "index" : 14, "hscan" : { "minimum" : 0.5000, "maximum" : 0.5714 }, "vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 } }, { "index" : 15, "hscan" : { "minimum" : 0.4286, "maximum" : 0.5000 }, "vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 } }, { "index" : 16, "hscan" : { "minimum" : 0.3571, "maximum" : 0.4286 }, "vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 } }, { "index" : 17, "hscan" : { "minimum" : 0.2857, "maximum" : 0.3571 }, "vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 } }, { "index" : 18, "hscan" : { "minimum" : 0.2143, "maximum" : 0.2857 }, "vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 } }, { "index" : 19, "hscan" : { "minimum" : 0.1429, "maximum" : 0.2143 }, "vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 } }, { "index" : 20, "hscan" : { "minimum" : 0.0714, "maximum" : 0.1429 }, "vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 } }, { "index" : 21, "hscan" : { "minimum" : 0.0000, "maximum" : 0.0714 }, "vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 } }, { "index" : 22, "hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 }, "vscan" : { "minimum" : 0.0000, "maximum" : 0.1250 } }, { "index" : 23, "hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 }, "vscan" : { "minimum" : 0.1250, "maximum" : 0.2500 } }, { "index" : 24, "hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 }, "vscan" : { "minimum" : 0.2500, "maximum" : 0.3750 } }, { "index" : 25, "hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 }, "vscan" : { "minimum" : 0.3750, "maximum" : 0.5000 } }, { "index" : 26, "hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 }, "vscan" : { "minimum" : 0.5000, "maximum" : 0.6250 } }, { "index" : 27, "hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 }, "vscan" : { "minimum" : 0.6250, "maximum" : 0.7500 } }, { "index" : 28, "hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 }, "vscan" : { "minimum" : 0.7500, "maximum" : 0.8750 } }, { "index" : 29, "hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 }, "vscan" : { "minimum" : 0.8750, "maximum" : 1.0000 } }, { "index" : 30, "hscan" : { "minimum" : 0.0000, "maximum" : 0.0714 }, "vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 } }, { "index" : 31, "hscan" : { "minimum" : 0.0714, "maximum" : 0.1429 }, "vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 } }, { "index" : 32, "hscan" : { "minimum" : 0.1429, "maximum" : 0.2143 }, "vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 } }, { "index" : 33, "hscan" : { "minimum" : 0.2143, "maximum" : 0.2857 }, "vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 } }, { "index" : 34, "hscan" : { "minimum" : 0.2857, "maximum" : 0.3571 }, "vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 } }, { "index" : 35, "hscan" : { "minimum" : 0.3571, "maximum" : 0.4286 }, "vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 } }, { "index" : 36, "hscan" : { "minimum" : 0.4286, "maximum" : 0.5000 }, "vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 } }, { "index" : 37, "hscan" : { "minimum" : 0.5000, "maximum" : 0.5714 }, "vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 } }, { "index" : 38, "hscan" : { "minimum" : 0.5714, "maximum" : 0.6429 }, "vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 } }, { "index" : 39, "hscan" : { "minimum" : 0.6429, "maximum" : 0.7143 }, "vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 } }, { "index" : 40, "hscan" : { "minimum" : 0.7143, "maximum" : 0.7857 }, "vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 } }, { "index" : 41, "hscan" : { "minimum" : 0.7857, "maximum" : 0.8571 }, "vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 } }, { "index" : 42, "hscan" : { "minimum" : 0.8571, "maximum" : 0.9286 }, "vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 } }, { "index" : 43, "hscan" : { "minimum" : 0.9286, "maximum" : 1.0000 }, "vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 } } ], "endOfJson" : "endOfJson" }Enig idee wat hier de oorzaak zou van kunnen zijn?
Thanks!