maybe you can just take kind of a "screenshot" of the "no-signal-image" and save this as setting to recognize when there is no signal?
Beiträge von Wastl
-
-
es war interessant, welches gerät du denn verwendest, schließlich ist ein Pi ja nicht das einzig unterstützte. aber das kann man ja jetzt herauslesen, danke dir.
-
did you update to libreelec or a fresh install?
i updated from OE to LE, too. after that hyperion worked fine. -
vielleicht noch etwas zur hardware bitte
-
es geht nur darum dass du ein perfekt weißes Bild zum darstellen hast. kannst es auch in JPG konvertieren, das sollte funktionieren.
-
which OS do you use? I had some similar effects with openELEC. I had to kill hyperion and restart it until it worked again.
Moving to libreELEC solved this issue. -
ich kann mir irgendwie auch nicht vorstellen dass es am strip oder der verkabelung liegt. sonst würde doch gar kein effekt funktionieren. reicht die stromversorgung definitiv aus? weil knapp 300 LEDs schnupfen ja einiges weg. ansonsten vielleicht hyperion nochmal neu installieren. ich bin auch von openelec auf libreelec umgestiegen. theoretisch sollte es ja aktuell nahezu keinen unterschied machen, aber gerade im bezug auf hyperion machte es bei mir welten aus in bezug auf die stabilität (natürlich eine verbesserung).
-
yes, i've got such a rainbow-grabber :puke: maybe it's more priceworthy to buy another one than to develop a solution for those
-
but not every grabber sends just blue when there is no signal. so this could just be a workaround for some people. brindosch asked for a solution for everybody.
-
Was ist denn hier der Flaschenhals? Die Eckverbinder etwa?
Beim Lightberry-Kit waren so selbstklebende Winkel dabei, damit man den LED-Strip nach außen gedreht (nicht nach hinten gerichtet) um den TV-Rand legen kann. Dadurch muss man den Streifen an den Ecken auch nicht abschneiden und Verbindungen schaffen. Ist das nicht die sicherste Lösung? -
I had the same "problem" with my config of the lightberry-kit. it seems, lightberry changed the type of LEDs. my old kit is working with WS2801, the new ones with APA102.
I solved my problem by choosing "WS2801" in HyperCon. just give it a try -
36 LED/m should be enough, shouldn't it?
-
I'm using WS2801 on RPi2 with OpenELEC/LibreELEC with RGB. To get a good whitelevel I have to go down with G and B, too, but not so much as you did.
-
may you please upload your .json? Maybe somebody can give a hint based on it
-
wow lightberry-support/wiki has grown
to deactivate unused LEDs:"transform":[
{
"id":"default",
"leds":"0-87",
[...]
{
"id":"turnedoff",
"leds":"88-120",
"hsv":{
"saturationGain":1.0000,
"valueGain":0.0000
},Lightberry still recommends following entry in .json for WS2801-LEDs. This works fine (also does type = WS2801).
"device": {
"name" : "MyPi",
"type" : "lightberry",
"output" : "/dev/spidev0.0",
"rate" : 1000000,
"colorOrder" : "rgb"
}, -
oh boy, heureka!
last night i couldn't fall asleep thinking of this issue. but then I got the right idea
I hope it is ok to explain it in german. there was no bug, whether in config nor elsewhere.In der alten .json war als Typ "lightberry" eingetragen, womit diese prima funktioniert hat. Da das aktuelle HyperCon diese Option nicht mehr bietet habe ich ein paar Möglichkeiten ausprobiert. Ich dachte eigentlich, es wären APA102-LEDs, doch mit dieser Option leuchteten einfach alle LEDs und waren nicht zu steuern. Als ich dann offenbar korrekt auf WS2801 gestellt habe, lief Hyperion mit der Config korrekt. Wenn mans genau nimmt, habe ich meinen eigenen Fehler im ersten Beitrag sogar selbst gelöst Die LEDs, welche nicht durch das .json konfiguriert waren, haben einfach ihre letzte Einstellung beibehalten. Da diese also durch die erste Fehlkonfiguration alle leuchteten, blieben sie halt einfach an.
Lösung:
Ich musste den lightstrip einfach kurz stromlos machen damit alle LEDs aus sind, wieder einstecken, fertig. Nicht konfigurierte LEDs bleiben aus, die 88 anderen werden durch Hyperion wie gewünscht gesteuert.
Die bessere Lösung wär vielleicht gewesen, die nicht verwendeten LEDs "schwarz" zu konfigurieren, damit diese aktiv deaktiviert werden. Wie könnte ich das am einfachsten erreichen?Um euere Frage zu beantworten:
Nicht verwendete LEDs deshalb, weil der Lightstrip 5m lang ist, mein TV aber einen geringeren Umfang hat. Ich muss ihn ja nicht abschneiden sondern brauche einfach nur nicht alle LEDs zu konfigurieren.OK now back to english, maybe this is interesting for somebody else:
yes the old .json did not break Hyperion, but it worked quite bad. I had to cut off many pixels from the bottom, because the LEDs stayed dark. I'm using an external usb-grabber.And, I forgot this to mention yesterday, I can't get a logfile from hyperion! HyperCon answers, there is no such file.
Thank you very much guys! This project is awesome =)
-
Hi,
i've been using Hyperion on RPi2 with openELEC for quite a long time and it worked (nearly) flawless.
Today I updated/changed from openELEC to LibreELEC 7.0.1, and after that, I also updated Hyperion to 1.03 (from 1.02 I think). This worked, but of course I had to update my config, too. (HyperCon 1.03.1).
Wow this will cost me some time to calibrate the colors again, but I managed to bring hyperion back to life =)But:
I'm using a lightstripe from lightberry (WS2801?) and configured 88 LEDs. These 88 LEDs work fine, but now the not used LEDs (89+) are always lighting. Sending a static color with brightness=0, 88 LEDs are dark, the others don't react to anything. I don't know wether the problem came up with LibreELEC or Hyperion 1.03. I think, my config is OK. I don't know how to go on. What can I do/try/test...?Thanks in advance,
Bastian