thx a lot
Beiträge von Tyler983
-
-
@Lord-Grey I know I'm bothering you and I'm so sorry about it.
As I read around, many peoples didn't had problem with ezcap269 and started led just plugging in the usb. So decided to buy it too...I know, there's a problem with writing data to the ttyACM0 but I don't know how to solve it, because of it I opened this post.
I hope to solve it as soon as possible cause I'm getting crazy, and I think also you because of your patience.
Really thx for support -
Trying to disable bluetooth...
this is my rfkill list:
pi@HyperBian:~ $ rfkill list0: phy0: Wireless LAN
Soft blocked: yes
Hard blocked: no
1: hci0: Bluetooth
Soft blocked: yes
Hard blocked: no
I don't understand if it's disabled or not
-
@Lord-Grey I start to study the article...
Meanwhile I started a debug and it seems no error but continue to make it in loop:
2020-09-16T20:37:53.223 hyperiond HYPERION : <DEBUG> PriorityMuxer.cpp:238:setInputImage() | Priority 250 is now active2020-09-16T20:37:58.683 hyperiond HYPERION : <DEBUG> PriorityMuxer.cpp:238:setInputImage() | Priority 250 is now inactive
following the debug txt
As I have understood from the article I should deactivate Bluetooth.
is this the command? sudo systemctl disable hciuart -
I was suspecting the same yesterday... luckily i have a new one somewhere, when i'll be at home i will install the new one and we'll see...
-
Hey @Awawa you just know my situation... do you know i can solve my issues installing your latest fork?
-
I tested hyperbian with the rpi4 yesterday. see post: https://hyperion-project.org/t…9.10746/page-3#post-27807
I remember good, but what i can't understand is why i have no led response... -
Guys, you are and where so gentle and kind. If you need an hep' to understand how hyperion ng act in the rpi4 ambient, i can wait and help you testing on my own with your indications
-
Well I'm just using the lightberry led system, the rest is all new (ezcap269 and rpi4). Anyway I also own a rpi3 if could be better to use...
-
-
With a dmesg always the same errors...
-
Plugged into usb 2 right now, yes the firmware is updated to the last one and I always had the video preview; still now that I haven't effect on the tv, I can watch the preview ...
-
why when I give sudo systemctl stop hyperion.service && /usr/share/hyperion/bin/hyperiond -d I found in the web gui this?
and when I newly active the grabber and the number of leds I have:2020-09-15T21:31:02.125 hyperiond V4L2:AUTO : <INFO> search for usable video devices
2020-09-15T21:31:02.127 hyperiond V4L2:AUTO : <INFO> test v4l device: /dev/video0
2020-09-15T21:31:02.139 hyperiond V4L2:AUTO : <DEBUG> V4L2Grabber.cpp:696:init_device() | Set resolution to width=1920 height=1080
2020-09-15T21:31:02.150 hyperiond V4L2:AUTO : <DEBUG> V4L2Grabber.cpp:713:init_device() | Set framerate to 30 fps
2020-09-15T21:31:02.150 hyperiond V4L2:AUTO : <DEBUG> V4L2Grabber.cpp:735:init_device() | Pixel format=YUYV
2020-09-15T21:31:02.187 hyperiond V4L2:AUTO : <INFO> found usable v4l2 device: /dev/video0 (ezcap U3 capture: ezcap U3 capt)
2020-09-15T21:31:02.190 hyperiond V4L2:AUTO : <INFO> Started
2020-09-15T21:31:02.190 hyperiond V4L2:auto : <DEBUG> GrabberWrapper.cpp:48:start() | Grabber start()
2020-09-15T21:31:02.191 hyperiond V4L2:AUTO : <ERROR> Frame too small: 0 != 4147200
2020-09-15T21:31:02.451 hyperiond HYPERION : <DEBUG> PriorityMuxer.cpp:238:setInputImage() | Priority 240 is now active
2020-09-15T21:31:02.451 hyperiond HYPERION : <DEBUG> PriorityMuxer.cpp:333:setCurrentTime() | Set visible priority to 240
2020-09-15T21:31:02.452 hyperiond HYPERION : <DEBUG> Hyperion.cpp:538:handlPriorityChangedLedDevice() | priority[240], previousPriority[250]
2020-09-15T21:31:10.812 hyperiond V4L2:AUTO : <ERROR> Previous line repeats 3 times
2020-09-15T21:31:10.812 hyperiond COMPONENTREG : <DEBUG> ComponentRegister.cpp:50:handleCompStateChangeRequest() | Disable Hyperion, store current component states
2020-09-15T21:31:10.812 hyperiond COMPONENTREG : <DEBUG> ComponentRegister.cpp:36:setNewComponentState() | Hyperion: disabled
2020-09-15T21:31:10.813 hyperiond COMPONENTREG : <DEBUG> ComponentRegister.cpp:36:setNewComponentState() | Smoothing: disabled
2020-09-15T21:31:10.813 hyperiond COMPONENTREG : <DEBUG> ComponentRegister.cpp:36:setNewComponentState() | Blackborder detector: disabled
2020-09-15T21:31:10.814 hyperiond HYPERION : <DEBUG> PriorityMuxer.cpp:255:clearInput() | Removed source priority 250
2020-09-15T21:31:10.814 hyperiond COMPONENTREG : <DEBUG> ComponentRegister.cpp:36:setNewComponentState() | Framegrabber: disabled
Hyperion caught signal :SIGSEGV
2020-09-15T21:31:10.815 hyperiond HYPERION : <DEBUG> PriorityMuxer.cpp:255:clearInput() | Removed source priority 240
2020-09-15T21:31:10.816 hyperiond HYPERION : <DEBUG> PriorityMuxer.cpp:333:setCurrentTime() | Set visible priority to 254
2020-09-15T21:31:10.816 hyperiond HYPERION : <DEBUG> Hyperion.cpp:538:handlPriorityChangedLedDevice() | priority[254], previousPriority[240]
2020-09-15T21:31:10.816 hyperiond CORE : <ERROR> /lib/arm-linux-gnueabihf/libc.so.6(__default_rt_sa_restorer+0) [0xb55a0130]
2020-09-15T21:31:10.816 hyperiond COMPONENTREG : <DEBUG> ComponentRegister.cpp:36:setNewComponentState() | V4L capture device: disabled
Segmentation fault
-
-
Which Arduino Sketch is running on your Arduino Leonardo?
I haven't Arduino, just rpi4 and ezcap 269
-
Done, but still nothing, leds are always off. Just at boot they show rgb colors but not swirl...
-
pi@HyperBian:~ $ lsusb
Bus 002 Device 002: ID 1bcf:2c99 Sunplus Innovation Technology Inc.
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 003: ID 2341:8036 Arduino SA Leonardo (CDC ACM, HID)
Bus 001 Device 002: ID 2109:3431 VIA Labs, Inc. Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
pi@HyperBian:~ $
-
Now it doesn't connect to the webgui...
-
-