Found the error! Cable length between converter and grabber was too long (I think).
When I changed my faulty hdmi converter, I also switched to the new rca cable (2m) that was included. Didn't imagine this could be the error since I got a valid screenshot, and picture also showed nicely when connected signal directly to TV.
But switching back to a 1m cable worked like a charm.
Yes, its directly plugged in. Pi also powers wifi and arduino (but leds themself have own power). I'll try removing wifi, and if that won't work - buy a usb hub with power supply. But its strange since it worked flawlessly before.
Thanks for all help so far!
Also, don't know if this helps:
-Screenshotting via HyperCon now makes hypercon unresponsive (take grabber screenshot). Didn't behave like this back in the days. Fix is to unplug grabber and replug. Have three 007 grabbers, and they all behave like this.
-Screenshotting via ssh (hyperion-v4l2 --screenshot) still works great.
Sure!
osmc@RogerPC:~$ hyperiond /etc/hyperion/hyperion.config.json
Hyperion Ambilight Deamon (2202)
Version : V1.03.2 (brindosch-99d9396/d3713a8-1469452981
Build Time: Jul 25 2016 06:54:40
INFO: Selected configuration file: /etc/hyperion/hyperion.config.json
HYPERION INFO: ColorTransform 'default' => [0; 81]
HYPERION INFO: ColorCorrection 'default' => [0; 81]
HYPERION INFO: ColorAdjustment 'default' => [0; 81]
LEDDEVICE INFO: configuration:
{
"colorOrder" : "rgb",
"delayAfterConnect" : 0,
"name" : "myPi",
"output" : "/dev/ttyUSB0",
"rate" : 115200,
"type" : "adalight"
}
Opening UART: /dev/ttyUSB0
INFO: Creating linear smoothing
HYPERION (CS) INFO: Created linear-smoothing(interval_ms=50;settlingTime_ms=200;updateDelay=0
EFFECTENGINE INFO: 27 effects loaded from directory /usr/share/hyperion/effects
EFFECTENGINE INFO: Initializing Python interpreter
INFO: Hyperion started and initialised
INFO: Boot sequence 'Rainbow swirl fast' EFFECTENGINE INFO: run effect Rainbow swirl fast on channel 0
BLACKBORDER INFO: threshold set to 0.01 (3)
BLACKBORDER INFO: mode:default
started
INFO: Json server created and started on port 19444
INFO: Proto server created and started on port 19445
V4L2GRABBER INFO: width=720 height=576
V4L2GRABBER INFO: pixel format=YUYV
BLACKBORDER INFO: threshold set to 0.01 (3)
BLACKBORDER INFO: mode:default
V4L2GRABBER INFO: signal threshold set to: {25,25,25}
V4L2GRABBER INFO: started
INFO: V4L2 grabber created and started
V4L2GRABBER INFO: stopped
EFFECTENGINE INFO: effect finished
V4L2GRABBER INFO: started
Shouldn't have the boot rainbow effect if this was wrong, but did as you said - and ttyUSB0 disappeared.
did you updated hyperion? could you post your config on pastebin
Sure! And yes, update Hyperion through hyperCon on a regular basis
[MEDIA=pastebin]YwYL16Qr[/MEDIA]
Hi guys, I need some help troubleshooting my setup. Made a post earlier, and found out my hdmi-s-video converter was faulty. This has been replaced now.
My gear is a rp2 + arduino nano (adafruit code) + WS2812. System has been working fine before, but after a couple of months being idle (and now updating osmc and hyperion), I can't get my ambi working properly again.
As title says, starting hyperion with rainbow boot-animation works great (so I guess nothing is wrong with the arduino, haven't touched the setup there), screenshotting from ssh works great (so I guess the video signal to the PI works great). Screensshotting from Hypercon makes Hypercon freeze. Unplugging the grabber makes it OK again.
Setting colors manually from HyperCon also works great.
So I'm a bit baffled to what can have gone wrong.
After updating to the new Hypercon and sending the config-files from there - I notice the hyperion.config.json now lies in etc/hyperion. Before, I remember dragging the config just to etc/ - and it got linked to somwhere else (file had this arrow icon in the bottom corner).
Could this be a part of the problem?
Thanks for all your help!
Ah..Faulty hdmi to s video converter. Not correlated to update, obviously.
My setup worked fine before. Just the other day I updated Hyperion though HyperCon (and also updated OSMC to latest stable release), and noticed an offset in my leds afterwards.
Took another screenshot in HyperCon and noticed this shift.
I was able to remove black border (A) by setting crop to 95, but can't find a way to show the missing picture in B (like a negative crop value, switching from PAL to NTSC etc).
Tried two other 007 grabbers, with same result. But as I said, this happened when updating Hyperion/OSMC. Setup worked fine before.
(but don't know what version I was on previously)
Edit: Maybe a month or so since I last updated through hyperCon
Anyone else with this problem?
