Ce grabber marche parfaitement
https://fr.aliexpress.com/item…042311.0.0.60f96c37nhTjzx
et pour les profilés alu, il y a ça :
https://fr.aliexpress.com/item…b201602_,searchweb201603_
Ce grabber marche parfaitement
https://fr.aliexpress.com/item…042311.0.0.60f96c37nhTjzx
et pour les profilés alu, il y a ça :
https://fr.aliexpress.com/item…b201602_,searchweb201603_
@NeeeB :
The solution for the freezing Libreelec, does it still work or did you find another one ?
Still work, you can lower the frequency or the resolution, both work.
Last position is B
D is third
Sorry, A Commnent is confuse
Go with the 4th one, on the right, I'm using it at the moment and it works like a charm, recognized directly by Hyperion.
@NeeeeB You first problem should be fixed once the following PR gets merged : https://github.com/hyperion-project/hyperion.ng/pull/894 .
For the second problem, you need to give more details like your setup, hardware, logs,...
I'll give more details about my setup tomorrow.
Also, where do I find the logs ?
Thx
Back with the details :
- Pi3 running latest LibreElec (9.2.3), fresh install with almost no addon except for Cinemavision, YeeMee and Hyperion-Control.
- WS2812b leds ran by an Arduino Uno plugged by USB to the Pi.
- Picture is captured by an Easycap UTV007 (RCA)
- Pi is plugged in a Yamaha RX-V385, EasyCap gets pictures from a Scart-out on the (old) LCD TV.
- That same setup worked as intended before reinstallation (no freeze), had to fully reinstall following a crash right after update to LibreElec 9.2.3
I've just enabled the Debug logs, I will try a restart this evening, I had to do it yesterday and it took me 5 attempts to make it work...first time Hyperion lost my PAL setting for my USBCapture device, so colors were wrong.
And then at every restart USBCapture was said to be enabled, but Leds did not light up...
Finally after 5 attempts it worked.
Also, where can I find help for Hyperion-control ? I don't understand how to set up some options, it looks like it does not work...
Thx !
Well, @Paulchen-Panther 's advice works well, just that little "unexpected end of stream" message received by YATSE, but in the end hyperion restarts so that's okay for me.
What's bothering me more is that freeze right after the rainbow swirl effect...it happens every time, even if I restart the Pi by unplug/plug it
https://github.com/hyperion-pr…api/JsonAPI.cpp#L844-L882
I think the "config" command with subcommand "reload"
Thanks, it works but I get a "unexpected end of stream" message every Time I use it.
This is the json I send : {"command":"config","subcommand":"reload"}
Also, after a fresh install, every time I restart hyperion or my Pi, hyperion stucks on the rainbow swirl (Frozen), I have to disable/enable it for it to work.
Any Idea ? Thx
Heu en fait que mette n'importe quoi en 4K ça fonctionne bien avec grabber.
Après il y a le plan au dos pour les 1 et 0 !!
Ouais j'ai bien vu le schéma sur le boîtier mais c'est pas super clair...mais bon si tu me dis que ça marche en 000 bah je verrai bien ahah
Merci !
Hi !!
I'm trying to add some custom commands to Yatse in order to control Hyperion.
I've had a look here :
https://docs.hyperion-project.org/en/json/
and so far I've managed to create custom commands to enable/disable Hyperion (with component ALL set to false/true).
I'd like to know if there is a json command to restart/reboot Hyperion, I couldn't find one in the wiki.
Many thanks !
J'ai reçu mon splitter aliexpress : https://fr.aliexpress.com/item/32567839827.html
test OK
aussi en 4k@60hz + 1080p@60hz
il s'en sort aussi bien que celui d'amazon payé le double ( pour rappel :)
Je viens de recevoir le mien, le même que toi donc, pourrais tu me donner ta config EDID pour avoir 4k sur une sortie et 1080 sur l'autre ? je ne suis pas certain de bien comprendre les instructions sur le boitier et je n'ai pas eu de manuel avec.
Autre chose, j'ai commandé ça :
https://fr.aliexpress.com/item…042311.0.0.701b6c37QiJ8sP
Il me semble avoir compris que tu avais le même également, tu me confirmes que ça fonctionne sans souci ?
Je ne peux pas tester pour le moment, j'attend mon Pi4 et surtout je n'ai pas (encore) de TV 4K, mais je prépare mon installation pour quand je vais y passer.
Merci !
Je pense oui
Testé Youtube HDR, ça fonctionne, donc splitter HDR ok !
Celui d'aliexpress ? Parce que j'ai commandé le même du coup
Bon tout est OK sur GPIO12 je suis content.
Une astuce pour les coins dans le LED layout ?
Sachant que j'aurais des connecteurs en L, il faut mettre un Edge Gap ?
Pas d'astuce malheureusement...
Dans Hypercon on pouvait gérer ce genre de truc mais avec Hyperion.NG je n'ai pas trouvé comment faire.
Changing widht/height in the config is not working for me.
As soon as I start hyperion the netflix-stream goes blank. Help please, this makes Hyperion completely unusable for me.
Go to Kodi settings and change GUI resolution from 1080p 60hz to 1080p 30hz.
That's how I fixed this problem on my end.
Je n'ai pas ces problèmes mais je passe par un Arduino Uno branché en USB sur le Pi...
Pour la décimation tu peux réduire jusque 4, ce n'est pas essentiel d'avoir une image "propre" sur la preview et surtout en augmentant la décimation tu réduis la charge mémoire sur le Pi.
Moi par exemple si je met à 1, il freeze au bout d'un moment, manque de ram (j'ai un pi 3).
Pour ce qui est des couleurs oui tu peux tout régler depuis l'interface web, ça prend un peu de temps mais une fois que c'est fait, c'est tout bon.
Je t'invite à jeter un oeil ici:
https://hyperion-project.org/wiki/Color-Calibration
C'est pour Hypercon mais c'est valable également pour Hyperion.ng et surtout tu trouveras les liens vers les images de calibration des couleurs
Try to switch Kodi resolution (the GUI) to 1080 30hz instead of 1080 60hz in kodi settings.
At least it worked for me, even though I can't find a direct relation to kodi GUI resolution and Hyperion...
Effectivement je pense que le bandeau est HS.
Effectivement y'a un petit souci
Aller je suis joueur, j'ai pris ça aussi sur Aliexpress pour tester :
https://fr.aliexpress.com/item/32567839827.html
ça servira peut être à la communauté !
Ah oui bien !!
Tu nous feras un retour s'il te plait, parce que s'il marche bien ça vaut vraiment le coup pour le prix.