Thanks for quick reply Arakon,
Could you explain benefits of using just raspberry alone? As i thought split load on arduino and raspberry will be more quicker.
If it is better could you link me please to how to example that i could retry of doing my project
I got smart TV so i use raspberry just for hyperion and arduino just controls LED
Hyperion is configured by basics nothing special, please see attached pictures.
http://prntscr.com/ncb6yg (Hardware)
http://prntscr.com/ncb76n (Grabber)
I am runing 258 LED on my TV and arduino sketch as follow:
#include "FastLED.h"
#define ANALOG_MODE_AVERAGE 0
#define ANALOG_MODE_LAST_LED 1
/**************************************
S E T U P
set following values to your needs
**************************************/
#define INITIAL_LED_TEST_ENABLED true
#define INITIAL_LED_TEST_BRIGHTNESS 32 // 0..255
#define INITIAL_LED_TEST_TIME_MS 3000 // 10..
// Number of leds in your strip. set to "1" and ANALOG_OUTPUT_ENABLED to "true" to activate analog only
// As of 26/1/2017:
// 582 leaves ZERO bytes free and this
// 410 is ok
// tested with 500 leds and is fine (despite the warning)
#define MAX_LEDS 258
// type of your led controller, possible values, see below
#define LED_TYPE WS2812B
// 3 wire (pwm): NEOPIXEL BTM1829 TM1812 TM1809 TM1804 TM1803 UCS1903 UCS1903B UCS1904 UCS2903 WS2812 WS2852
// S2812B SK6812 SK6822 APA106 PL9823 WS2811 WS2813 APA104 WS2811_40 GW6205 GW6205_40 LPD1886 LPD1886_8BIT
// 4 wire (spi): LPD8806 WS2801 WS2803 SM16716 P9813 APA102 SK9822 DOTSTAR
// For 3 wire led stripes line Neopixel/Ws2812, which have a data line, ground, and power, you just need to define DATA_PIN.
// For led chipsets that are SPI based (four wires - data, clock, ground, and power), both defines DATA_PIN and CLOCK_PIN are needed
// DATA_PIN, or DATA_PIN, CLOCK_PIN
#define LED_PINS 6 // 3 wire leds
//#define LED_PINS 6, 13 // 4 wire leds
#define COLOR_ORDER GRB // colororder of the stripe, set RGB in hyperion
#define OFF_TIMEOUT 15000 // ms to switch off after no data was received, set 0 to deactivate
// analog rgb uni color led stripe - using of hyperion smoothing is recommended
// ATTENTION this pin config is default for atmega328 based arduinos, others might work to
// if you have flickering analog leds this might be caused by unsynced pwm signals
// try other pins is more or less the only thing that helps
#define ANALOG_OUTPUT_ENABLED false
#define ANALOG_MODE ANALOG_MODE_LAST_LED // use ANALOG_MODE_AVERAGE or ANALOG_MODE_LAST_LED
#define ANALOG_GROUND_PIN 8 // additional ground pin to make wiring a bit easier
#define ANALOG_RED_PIN 9
#define ANALOG_GREEN_PIN 10
#define ANALOG_BLUE_PIN 11
// overall color adjustments
#define ANALOG_BRIGHTNESS_RED 255 // maximum brightness for analog 0-255
#define ANALOG_BRIGHTNESS_GREEN 255 // maximum brightness for analog 0-255
#define ANALOG_BRIGHTNESS_BLUE 255 // maximum brightness for analog 0-255
#define BRIGHTNESS 255 // maximum brightness 0-255
#define DITHER_MODE BINARY_DITHER // BINARY_DITHER or DISABLE_DITHER
#define COLOR_TEMPERATURE CRGB(255,255,255) // RGB value describing the color temperature
#define COLOR_CORRECTION TypicalLEDStrip // predefined fastled color correction
//#define COLOR_CORRECTION CRGB(255,255,255) // or RGB value describing the color correction
// Baudrate, higher rate allows faster refresh rate and more LEDs
//#define serialRate 460800 // use 115200 for ftdi based boards
#define serialRate 115200 // use 115200 for ftdi based boards
//#define serialRate 500000 // use 115200 for ftdi based boards
/**************************************
A D A L I G H T C O D E
no user changes needed
**************************************/
// Adalight sends a "Magic Word" (defined in /etc/boblight.conf) before sending the pixel data
uint8_t prefix[] = {'A', 'd', 'a'}, hi, lo, chk, i;
unsigned long endTime;
// Define the array of leds
CRGB leds[MAX_LEDS];
// set rgb to analog led stripe
void showAnalogRGB(const CRGB& led) {
if (ANALOG_OUTPUT_ENABLED) {
byte r = map(led.r, 0,255,0,ANALOG_BRIGHTNESS_RED);
byte g = map(led.g, 0,255,0,ANALOG_BRIGHTNESS_GREEN);
byte b = map(led.b, 0,255,0,ANALOG_BRIGHTNESS_BLUE);
analogWrite(ANALOG_RED_PIN , r);
analogWrite(ANALOG_GREEN_PIN, g);
analogWrite(ANALOG_BLUE_PIN , b);
}
}
// set color to all leds
void showColor(const CRGB& led) {
#if MAX_LEDS > 1 || ANALOG_OUTPUT_ENABLED == false
LEDS.showColor(led);
#endif
showAnalogRGB(led);
}
// switch of digital and analog leds
void switchOff() {
#if MAX_LEDS > 1 || ANALOG_OUTPUT_ENABLED == false
memset(leds, 0, MAX_LEDS * sizeof(struct CRGB));
FastLED.show();
#endif
showAnalogRGB(leds[0]);
}
// function to check if serial data is available
// if timeout occured leds switch of, if configured
bool checkIncommingData() {
boolean dataAvailable = true;
while (!Serial.available()) {
if ( OFF_TIMEOUT > 0 && endTime < millis()) {
switchOff();
dataAvailable = false;
endTime = millis() + OFF_TIMEOUT;
}
}
return dataAvailable;
}
// main function that setups and runs the code
void setup() {
Serial.begin(serialRate);
// analog output
if (ANALOG_OUTPUT_ENABLED) {
// additional ground pin to make wiring a bit easier
pinMode(ANALOG_GROUND_PIN, OUTPUT);
digitalWrite(ANALOG_GROUND_PIN, LOW);
pinMode(ANALOG_BLUE_PIN , OUTPUT);
pinMode(ANALOG_RED_PIN , OUTPUT);
pinMode(ANALOG_GREEN_PIN, OUTPUT);
}
int ledCount = MAX_LEDS;
if (ANALOG_MODE == ANALOG_MODE_LAST_LED) {
ledCount--;
}
#if MAX_LEDS > 1 || ANALOG_OUTPUT_ENABLED == false
FastLED.addLeds<LED_TYPE, LED_PINS, COLOR_ORDER>(leds, ledCount);
#endif
// color adjustments
FastLED.setBrightness ( BRIGHTNESS );
FastLED.setTemperature( COLOR_TEMPERATURE );
FastLED.setCorrection ( COLOR_CORRECTION );
FastLED.setDither ( DITHER_MODE );
// initial RGB flash
#if INITIAL_LED_TEST_ENABLED == true
for (int v=0;v<INITIAL_LED_TEST_BRIGHTNESS;v++)
{
showColor(CRGB(v,v,v));
delay(INITIAL_LED_TEST_TIME_MS/2/INITIAL_LED_TEST_BRIGHTNESS);
}
for (int v=0;v<INITIAL_LED_TEST_BRIGHTNESS;v++)
{
showColor(CRGB(v,v,v));
delay(INITIAL_LED_TEST_TIME_MS/2/INITIAL_LED_TEST_BRIGHTNESS);
}
#endif
showColor(CRGB(0, 0, 0));
Serial.print("Ada\n"); // Send "Magic Word" string to host
boolean transmissionSuccess;
unsigned long sum_r, sum_g, sum_b;
// loop() is avoided as even that small bit of function overhead
// has a measurable impact on this code's overall throughput.
for(;;) {
// wait for first byte of Magic Word
for (i = 0; i < sizeof prefix; ++i) {
// If next byte is not in Magic Word, the start over
if (!checkIncommingData() || prefix[i] != Serial.read()) {
i = 0;
}
}
// Hi, Lo, Checksum
if (!checkIncommingData()) continue;
hi = Serial.read();
if (!checkIncommingData()) continue;
lo = Serial.read();
if (!checkIncommingData()) continue;
chk = Serial.read();
// if checksum does not match go back to wait
if (chk != (hi ^ lo ^ 0x55)) continue;
memset(leds, 0, MAX_LEDS * sizeof(struct CRGB));
transmissionSuccess = true;
sum_r = 0;
sum_g = 0;
sum_b = 0;
int num_leds = min ( MAX_LEDS, (hi<<8) + lo + 1 );
// read the transmission data and set LED values
for (int idx = 0; idx < num_leds; idx++) {
byte r, g, b;
if (!checkIncommingData()) {
transmissionSuccess = false;
break;
}
r = Serial.read();
if (!checkIncommingData()) {
transmissionSuccess = false;
break;
}
g = Serial.read();
if (!checkIncommingData()) {
transmissionSuccess = false;
break;
}
b = Serial.read();
leds[idx].r = r;
leds[idx].g = g;
leds[idx].b = b;
#if ANALOG_OUTPUT_ENABLED == true && ANALOG_MODE == ANALOG_MODE_AVERAGE
sum_r += r;
sum_g += g;
sum_b += b;
#endif
}
// shows new values
if (transmissionSuccess) {
endTime = millis() + OFF_TIMEOUT;
#if MAX_LEDS > 1 || ANALOG_OUTPUT_ENABLED == false
FastLED.show();
#endif
#if ANALOG_OUTPUT_ENABLED == true
#if ANALOG_MODE == ANALOG_MODE_LAST_LED
showAnalogRGB(leds[MAX_LEDS-1]);
#else
showAnalogRGB(CRGB(sum_r/MAX_LEDS, sum_g/MAX_LEDS, sum_b/MAX_LEDS));
#endif
#endif
}
}
} // end of setup
void loop() {
// Not used. See note in setup() function.
}
Alles anzeigen
I know that i use ttyUSB0 and video0 by searching it through PuTTY ls -l /dev/*USB* and ls -l /dev/*video*
When i power up first by pluging mu 5v power supply and raspberry after i will get led sequence working after that in Hyperion if i click start i will get diferent sequence led playing than before so i dont know what they should mean.
I am attaching as well log file from my session:
SSH Traffic:
ssh connected
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: cd /tmp && wget -nv -N https://raw.github.com/hyperion-project/hyperion/master/bin/install_hyperion.sh && chmod +x install_hyperion.sh && sudo sh ./install_hyperion.sh HyperConInstall ; rm install_hyperion.sh
ssh out: Last-modified header missing -- time-stamps turned off.
ssh out: 2019-04-14 20:28:16 URL:https://raw.githubusercontent.com/hyperion-project/hyperion/master/bin/install_hyperion.sh [14552/14552] -> "install_hyperion.sh" [1]
ssh in: *******************************************************************************
ssh in: This script will install/update Hyperion Ambient Light
ssh in: Created by brindosch - hyperion-project.org - the official Hyperion source.
ssh in: *******************************************************************************
ssh in: ---> Stop Hyperion, if necessary
ssh in: ---> Install/Update Hyperion dependencies (This may take a while)
ssh out: debconf: unable to initialize frontend: Dialog
ssh out: debconf: (Dialog frontend will not work on a dumb terminal, an emacs shell buffer, or without a controlling terminal.)
ssh out: debconf: falling back to frontend: Readline
ssh out: debconf: unable to initialize frontend: Readline
ssh out: debconf: (Can't locate Term/ReadLine.pm in @INC (you may need to install the Term::ReadLine module) (@INC contains: /etc/perl /usr/local/lib/arm-linux-gnueabihf/perl/5.24.1 /usr/local/share/perl/5.24.1 /usr/lib/arm-linux-gnueabihf/perl5/5.24 /usr/share/perl5 /usr/lib/arm-linux-gnueabihf/perl/5.24 /usr/share/perl/5.24 /usr/local/lib/site_perl /usr/lib/arm-linux-gnueabihf/perl-base .) at /usr/share/perl5/Debconf/FrontEnd/Readline.pm line 7, <> line 21.)
ssh out: debconf: falling back to frontend: Teletype
ssh out: dpkg-preconfigure: unable to re-open stdin:
ssh in: Selecting previously unselected package fontconfig.
ssh in: (Reading database ...
ssh in: (Reading database ... 5%
ssh in: (Reading database ... 10%
ssh in: (Reading database ... 15%
ssh in: (Reading database ... 20%
ssh in: (Reading database ... 25%
ssh in: (Reading database ... 30%
ssh in: (Reading database ... 35%
ssh in: (Reading database ... 40%
ssh in: (Reading database ... 45%
ssh in: (Reading database ... 50%
ssh in: (Reading database ... 55%
ssh in: (Reading database ... 60%
ssh in: (Reading database ... 65%
ssh in: (Reading database ... 70%
ssh in: (Reading database ... 75%
ssh in: (Reading database ... 80%
ssh in: (Reading database ... 85%
ssh in: (Reading database ... 90%
ssh in: (Reading database ... 95%
ssh in: (Reading database ... 100%
ssh in: (Reading database ... 23428 files and directories currently installed.)
ssh in: Preparing to unpack .../00-fontconfig_2.11.0-6.7+b1_armhf.deb ...
ssh in: Unpacking fontconfig (2.11.0-6.7+b1) ...
ssh in: Selecting previously unselected package libxau6:armhf.
ssh in: Preparing to unpack .../01-libxau6_1%3a1.0.8-1_armhf.deb ...
ssh in: Unpacking libxau6:armhf (1:1.0.8-1) ...
ssh in: Selecting previously unselected package x11-common.
ssh in: Preparing to unpack .../02-x11-common_1%3a7.7+19_all.deb ...
ssh in: Unpacking x11-common (1:7.7+19) ...
ssh in: Selecting previously unselected package libice6:armhf.
ssh in: Preparing to unpack .../03-libice6_2%3a1.0.9-2_armhf.deb ...
ssh in: Unpacking libice6:armhf (2:1.0.9-2) ...
ssh in: Selecting previously unselected package libsm6:armhf.
ssh in: Preparing to unpack .../04-libsm6_2%3a1.2.2-1+b3_armhf.deb ...
ssh in: Unpacking libsm6:armhf (2:1.2.2-1+b3) ...
ssh in: Selecting previously unselected package libxdmcp6:armhf.
ssh in: Preparing to unpack .../05-libxdmcp6_1%3a1.1.2-3_armhf.deb ...
ssh in: Unpacking libxdmcp6:armhf (1:1.1.2-3) ...
ssh in: Selecting previously unselected package libxcb1:armhf.
ssh in: Preparing to unpack .../06-libxcb1_1.12-1_armhf.deb ...
ssh in: Unpacking libxcb1:armhf (1.12-1) ...
ssh in: Selecting previously unselected package libx11-data.
ssh in: Preparing to unpack .../07-libx11-data_2%3a1.6.4-3+deb9u1_all.deb ...
ssh in: Unpacking libx11-data (2:1.6.4-3+deb9u1) ...
ssh in: Selecting previously unselected package libx11-6:armhf.
ssh in: Preparing to unpack .../08-libx11-6_2%3a1.6.4-3+deb9u1_armhf.deb ...
ssh in: Unpacking libx11-6:armhf (2:1.6.4-3+deb9u1) ...
ssh in: Selecting previously unselected package libxt6:armhf.
ssh in: Preparing to unpack .../09-libxt6_1%3a1.1.5-1_armhf.deb ...
ssh in: Unpacking libxt6:armhf (1:1.1.5-1) ...
ssh in: Selecting previously unselected package libaudio2:armhf.
ssh in: Preparing to unpack .../10-libaudio2_1.9.4-5+b1_armhf.deb ...
ssh in: Unpacking libaudio2:armhf (1.9.4-5+b1) ...
ssh in: Selecting previously unselected package libmng1:armhf.
ssh in: Preparing to unpack .../11-libmng1_1.0.10+dfsg-3.1+b5_armhf.deb ...
ssh in: Unpacking libmng1:armhf (1.0.10+dfsg-3.1+b5) ...
ssh in: Selecting previously unselected package qtcore4-l10n.
ssh in: Preparing to unpack .../12-qtcore4-l10n_4%3a4.8.7+dfsg-11_all.deb ...
ssh in: Unpacking qtcore4-l10n (4:4.8.7+dfsg-11) ...
ssh in: Selecting previously unselected package libqtcore4:armhf.
ssh in: Preparing to unpack .../13-libqtcore4_4%3a4.8.7+dfsg-11_armhf.deb ...
ssh in: Unpacking libqtcore4:armhf (4:4.8.7+dfsg-11) ...
ssh in: Selecting previously unselected package libqt4-xml:armhf.
ssh in: Preparing to unpack .../14-libqt4-xml_4%3a4.8.7+dfsg-11_armhf.deb ...
ssh in: Unpacking libqt4-xml:armhf (4:4.8.7+dfsg-11) ...
ssh in: Selecting previously unselected package libqtdbus4:armhf.
ssh in: Preparing to unpack .../15-libqtdbus4_4%3a4.8.7+dfsg-11_armhf.deb ...
ssh in: Unpacking libqtdbus4:armhf (4:4.8.7+dfsg-11) ...
ssh in: Selecting previously unselected package libqt4-network:armhf.
ssh in: Preparing to unpack .../16-libqt4-network_4%3a4.8.7+dfsg-11_armhf.deb ...
ssh in: Unpacking libqt4-network:armhf (4:4.8.7+dfsg-11) ...
ssh in: Selecting previously unselected package libxext6:armhf.
ssh in: Preparing to unpack .../17-libxext6_2%3a1.3.3-1+b2_armhf.deb ...
ssh in: Unpacking libxext6:armhf (2:1.3.3-1+b2) ...
ssh in: Selecting previously unselected package libxrender1:armhf.
ssh in: Preparing to unpack .../18-libxrender1_1%3a0.9.10-1_armhf.deb ...
ssh in: Unpacking libxrender1:armhf (1:0.9.10-1) ...
ssh in: Selecting previously unselected package libqtgui4:armhf.
ssh in: Preparing to unpack .../19-libqtgui4_4%3a4.8.7+dfsg-11_armhf.deb ...
ssh in: Unpacking libqtgui4:armhf (4:4.8.7+dfsg-11) ...
ssh in: Selecting previously unselected package libusb-1.0-0:armhf.
ssh in: Preparing to unpack .../20-libusb-1.0-0_2%3a1.0.21-1_armhf.deb ...
ssh in: Unpacking libusb-1.0-0:armhf (2:1.0.21-1) ...
ssh in: Setting up libmng1:armhf (1.0.10+dfsg-3.1+b5) ...
ssh in: Setting up qtcore4-l10n (4:4.8.7+dfsg-11) ...
ssh in: Setting up libusb-1.0-0:armhf (2:1.0.21-1) ...
ssh in: Processing triggers for libc-bin (2.24-11+deb9u3) ...
ssh in: Setting up libqtcore4:armhf (4:4.8.7+dfsg-11) ...
ssh in: Processing triggers for systemd (232-25+deb9u6) ...
ssh in: Setting up libxdmcp6:armhf (1:1.1.2-3) ...
ssh in: Setting up x11-common (1:7.7+19) ...
ssh in: debconf: unable to initialize frontend: Dialog
ssh in: debconf: (Dialog frontend will not work on a dumb terminal, an emacs shell buffer, or without a controlling terminal.)
ssh in: debconf: falling back to frontend: Readline
ssh in: debconf: unable to initialize frontend: Readline
ssh in: debconf: (Can't locate Term/ReadLine.pm in @INC (you may need to install the Term::ReadLine module) (@INC contains: /etc/perl /usr/local/lib/arm-linux-gnueabihf/perl/5.24.1 /usr/local/share/perl/5.24.1 /usr/lib/arm-linux-gnueabihf/perl5/5.24 /usr/share/perl5 /usr/lib/arm-linux-gnueabihf/perl/5.24 /usr/share/perl/5.24 /usr/local/lib/site_perl /usr/lib/arm-linux-gnueabihf/perl-base .) at /usr/share/perl5/Debconf/FrontEnd/Readline.pm line 7.)
ssh in: debconf: falling back to frontend: Teletype
ssh in: /var/lib/dpkg/info/x11-common.postinst: line 13: update-rc.d: command not found
ssh in: dpkg: error processing package x11-common (--configure):
ssh in: subprocess installed post-installation script returned error exit status 127
ssh in: Setting up libx11-data (2:1.6.4-3+deb9u1) ...
ssh in: Setting up libqt4-xml:armhf (4:4.8.7+dfsg-11) ...
ssh in: Setting up libxau6:armhf (1:1.0.8-1) ...
ssh in: Setting up fontconfig (2.11.0-6.7+b1) ...
ssh in: Regenerating fonts cache... done.
ssh in: dpkg: dependency problems prevent configuration of libice6:armhf:
ssh in: libice6:armhf depends on x11-common; however:
ssh in: Package x11-common is not configured yet.
ssh in: dpkg: error processing package libice6:armhf (--configure):
ssh in: dependency problems - leaving unconfigured
ssh in: dpkg: dependency problems prevent configuration of libxt6:armhf:
ssh in: libxt6:armhf depends on libice6 (>= 1:1.0.0); however:
ssh in: Package libice6:armhf is not configured yet.
ssh in: dpkg: error processing package libxt6:armhf (--configure):
ssh in: dependency problems - leaving unconfigured
ssh in: Setting up libqtdbus4:armhf (4:4.8.7+dfsg-11) ...
ssh in: Setting up libxcb1:armhf (1.12-1) ...
ssh in: dpkg: dependency problems prevent configuration of libaudio2:armhf:
ssh in: libaudio2:armhf depends on libxt6; however:
ssh in: Package libxt6:armhf is not configured yet.
ssh in: dpkg: error processing package libaudio2:armhf (--configure):
ssh in: dependency problems - leaving unconfigured
ssh in: dpkg: dependency problems prevent configuration of libsm6:armhf:
ssh in: libsm6:armhf depends on libice6 (>= 1:1.0.0); however:
ssh in: Package libice6:armhf is not configured yet.
ssh in: dpkg: error processing package libsm6:armhf (--configure):
ssh in: dependency problems - leaving unconfigured
ssh in: dpkg: dependency problems prevent configuration of libqtgui4:armhf:
ssh in: libqtgui4:armhf depends on libaudio2; however:
ssh in: Package libaudio2:armhf is not configured yet.
ssh in: libqtgui4:armhf depends on libice6 (>= 1:1.0.0); however:
ssh in: Package libice6:armhf is not configured yet.
ssh in: libqtgui4:armhf depends on libsm6; however:
ssh in: Package libsm6:armhf is not configured yet.
ssh in: dpkg: error processing package libqtgui4:armhf (--configure):
ssh in: dependency problems - leaving unconfigured
ssh in: Setting up libx11-6:armhf (2:1.6.4-3+deb9u1) ...
ssh in: Setting up libxrender1:armhf (1:0.9.10-1) ...
ssh in: Setting up libqt4-network:armhf (4:4.8.7+dfsg-11) ...
ssh in: Setting up libxext6:armhf (2:1.3.3-1+b2) ...
ssh in: Processing triggers for libc-bin (2.24-11+deb9u3) ...
ssh in: Processing triggers for systemd (232-25+deb9u6) ...
ssh in: Errors were encountered while processing:
ssh in: x11-common
ssh in: libice6:armhf
ssh in: libxt6:armhf
ssh in: libaudio2:armhf
ssh in: libsm6:armhf
ssh in: libqtgui4:armhf
ssh out: E: Sub-process /usr/bin/dpkg returned an error code (1)
ssh in: ---> Raspberry Pi found, but SPI is not set, we write "dtparam=spi=on" to /boot/config.txt
ssh in: ---> Downloading the appropriate Hyperion release
ssh out: 2019-04-14 20:29:07 URL:https://netcologne.dl.sourceforge.net/project/hyperion-project/release/hyperion_rpi_osmc.tar.gz [1640849/1640849] -> "-" [1]
ssh in: ---> Installing systemd script
ssh out: Created symlink /etc/systemd/system/multi-user.target.wants/hyperion.service ¬ニメ /etc/systemd/system/hyperion.service.
ssh in: ---> Modify systemd script for OSMC usage
ssh in: ---> Starting Hyperion
ssh in: *******************************************************************************
ssh in: Hyperion Installation/Update finished!
ssh in: Please download the latest HyperCon version to benefit from new features!
ssh in: To create a config, follow the HyperCon Guide at our Wiki (EN/DE)!
ssh in: Wiki: wiki.hyperion-project.org Webpage: www.hyperion-project.org
ssh in: *******************************************************************************
ssh in: Rebooting now, we added dtparam=spi=on to config.txt
ssh disconnected
ssh connected
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null ; hyperion-v4l2 --device /dev/video0 --video-standard PAL --input 0 --width 1920 --height 1080 --crop-left 0 --crop-right 0 --crop-top 0 --crop-bottom 0 --size-decimator 1 --frame-decimator 2 --red-threshold 0.0 --green-threshold 0.0 --blue-threshold 0.0 --screenshot
ssh in: hyperion-v4l2:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:25
ssh out: VIDIOC_S_STD ERROR 25, Inappropriate ioctl for device
sftp getFile(./screenshot.png, java.awt.Image)
ssh out: hyperion-remote -c ff2427
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
ssh out: sudo journalctl -u hyperion.service 2>/dev/null
ssh in: -- Logs begin at Thu 2016-11-03 17:16:42 UTC, end at Sun 2019-04-14 20:38:12 UTC. --
ssh in: Apr 14 20:29:13 osmc systemd[1]: Started Hyperion Systemd service.
ssh in: Apr 14 20:29:14 osmc hyperiond[313]: Hyperion Ambilight Deamon (313)
ssh in: Apr 14 20:29:14 osmc hyperiond[313]: Version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: Apr 14 20:29:14 osmc hyperiond[313]: Build Time: Apr 5 2018 01:57:25
ssh in: Apr 14 20:29:14 osmc hyperiond[313]: ERROR: No valid config found
ssh in: Apr 14 20:29:15 osmc systemd[1]: hyperion.service: Main process exited, code=exited, status=1/FAILURE
ssh in: Apr 14 20:29:15 osmc systemd[1]: hyperion.service: Unit entered failed state.
ssh in: Apr 14 20:29:15 osmc systemd[1]: hyperion.service: Failed with result 'exit-code'.
ssh in: Apr 14 20:29:15 osmc systemd[1]: hyperion.service: Service hold-off time over, scheduling restart.
ssh in: Apr 14 20:29:15 osmc systemd[1]: Stopped Hyperion Systemd service.
ssh in: Apr 14 20:29:15 osmc systemd[1]: Started Hyperion Systemd service.
ssh in: Apr 14 20:29:15 osmc hyperiond[420]: Hyperion Ambilight Deamon (420)
ssh in: Apr 14 20:29:15 osmc hyperiond[420]: Version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: Apr 14 20:29:15 osmc hyperiond[420]: Build Time: Apr 5 2018 01:57:25
ssh in: Apr 14 20:29:15 osmc hyperiond[420]: ERROR: No valid config found
ssh in: Apr 14 20:29:15 osmc systemd[1]: hyperion.service: Main process exited, code=exited, status=1/FAILURE
ssh in: Apr 14 20:29:15 osmc systemd[1]: hyperion.service: Unit entered failed state.
ssh in: Apr 14 20:29:15 osmc systemd[1]: hyperion.service: Failed with result 'exit-code'.
ssh in: Apr 14 20:29:15 osmc systemd[1]: hyperion.service: Service hold-off time over, scheduling restart.
ssh in: Apr 14 20:29:15 osmc systemd[1]: Stopped Hyperion Systemd service.
ssh in: Apr 14 20:29:15 osmc systemd[1]: Started Hyperion Systemd service.
ssh in: Apr 14 20:29:15 osmc hyperiond[422]: Hyperion Ambilight Deamon (422)
ssh in: Apr 14 20:29:15 osmc hyperiond[422]: Version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: Apr 14 20:29:15 osmc hyperiond[422]: Build Time: Apr 5 2018 01:57:25
ssh in: Apr 14 20:29:15 osmc hyperiond[422]: ERROR: No valid config found
ssh in: Apr 14 20:29:15 osmc systemd[1]: hyperion.service: Main process exited, code=exited, status=1/FAILURE
ssh in: Apr 14 20:29:15 osmc systemd[1]: hyperion.service: Unit entered failed state.
ssh in: Apr 14 20:29:15 osmc systemd[1]: hyperion.service: Failed with result 'exit-code'.
ssh in: Apr 14 20:29:16 osmc systemd[1]: hyperion.service: Service hold-off time over, scheduling restart.
ssh in: Apr 14 20:29:16 osmc systemd[1]: Stopped Hyperion Systemd service.
ssh in: Apr 14 20:29:16 osmc systemd[1]: Started Hyperion Systemd service.
ssh in: Apr 14 20:29:16 osmc hyperiond[425]: Hyperion Ambilight Deamon (425)
ssh in: Apr 14 20:29:16 osmc hyperiond[425]: Version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: Apr 14 20:29:16 osmc hyperiond[425]: Build Time: Apr 5 2018 01:57:25
ssh in: Apr 14 20:29:16 osmc hyperiond[425]: ERROR: No valid config found
ssh in: Apr 14 20:29:16 osmc systemd[1]: hyperion.service: Main process exited, code=exited, status=1/FAILURE
ssh in: Apr 14 20:29:16 osmc systemd[1]: hyperion.service: Unit entered failed state.
ssh in: Apr 14 20:29:16 osmc systemd[1]: hyperion.service: Failed with result 'exit-code'.
ssh in: Apr 14 20:29:16 osmc systemd[1]: hyperion.service: Service hold-off time over, scheduling restart.
ssh in: Apr 14 20:29:16 osmc systemd[1]: Stopped Hyperion Systemd service.
ssh in: Apr 14 20:29:16 osmc systemd[1]: Started Hyperion Systemd service.
ssh in: Apr 14 20:29:16 osmc hyperiond[427]: Hyperion Ambilight Deamon (427)
ssh in: Apr 14 20:29:16 osmc hyperiond[427]: Version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: Apr 14 20:29:16 osmc hyperiond[427]: Build Time: Apr 5 2018 01:57:25
ssh in: Apr 14 20:29:16 osmc hyperiond[427]: ERROR: No valid config found
ssh in: Apr 14 20:29:16 osmc systemd[1]: hyperion.service: Main process exited, code=exited, status=1/FAILURE
ssh in: Apr 14 20:29:16 osmc systemd[1]: hyperion.service: Unit entered failed state.
ssh in: Apr 14 20:29:16 osmc systemd[1]: hyperion.service: Failed with result 'exit-code'.
ssh in: Apr 14 20:29:17 osmc systemd[1]: hyperion.service: Service hold-off time over, scheduling restart.
ssh in: Apr 14 20:29:17 osmc systemd[1]: Stopped Hyperion Systemd service.
ssh in: Apr 14 20:29:17 osmc systemd[1]: hyperion.service: Start request repeated too quickly.
ssh in: Apr 14 20:29:17 osmc systemd[1]: Failed to start Hyperion Systemd service.
ssh in: Apr 14 20:29:17 osmc systemd[1]: hyperion.service: Unit entered failed state.
ssh in: Apr 14 20:29:17 osmc systemd[1]: hyperion.service: Failed with result 'exit-code'.
ssh in: Apr 14 20:31:05 osmc systemd[1]: Started Hyperion Systemd service.
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: Hyperion Ambilight Deamon (823)
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: Version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: Build Time: Apr 5 2018 01:57:25
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: INFO: Selected configuration file: /etc/hyperion/hyperion.config.json
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: HYPERION INFO: ColorTransform 'default' => [0; 257]
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: HYPERION INFO: ColorCorrection 'default' => [0; 257]
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: HYPERION INFO: ColorAdjustment 'default' => [0; 257]
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: LEDDEVICE INFO: configuration:
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: {
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: "colorOrder" : "rgb",
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: "delayAfterConnect" : 0,
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: "name" : "MyHyperionConfig",
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: "output" : "/dev/ttyUSB0",
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: "rate" : 115200,
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: "type" : "adalight"
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: }
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: Opening UART: /dev/ttyUSB0
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: INFO: Creating linear smoothing
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: HYPERION (CS) INFO: Created linear-smoothing(interval_ms=50;settlingTime_ms=200;updateDelay=0
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: EFFECTENGINE INFO: 27 effects loaded from directory /usr/share/hyperion/effects
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: EFFECTENGINE INFO: Initializing Python interpreter
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: INFO: Hyperion started and initialised
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: INFO: Boot sequence 'Rainbow swirl fast' EFFECTENGINE INFO: run effect Rainbow swirl fast on channel 0
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: BLACKBORDER INFO: threshold set to 0 (0)
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: BLACKBORDER INFO: mode:default
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: started
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: INFO: Json server created and started on port 19444
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: INFO: Proto server created and started on port 19445
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: DISPMANXGRABBER INFO: Display opened with resolution: 720x480
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: BLACKBORDER INFO: threshold set to 0 (0)
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: BLACKBORDER INFO: mode:default
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: INFO: Frame grabber created and started
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: terminate called after throwing an instance of 'std::runtime_error'
ssh in: Apr 14 20:31:05 osmc hyperiond[823]: what(): VIDIOC_S_STD ERROR 25, Inappropriate ioctl for device
ssh in: Apr 14 20:31:05 osmc systemd[1]: hyperion.service: Main process exited, code=killed, status=6/ABRT
ssh in: Apr 14 20:31:05 osmc systemd[1]: hyperion.service: Unit entered failed state.
ssh in: Apr 14 20:31:05 osmc systemd[1]: hyperion.service: Failed with result 'signal'.
ssh in: Apr 14 20:31:05 osmc systemd[1]: hyperion.service: Service hold-off time over, scheduling restart.
ssh in: Apr 14 20:31:05 osmc systemd[1]: Stopped Hyperion Systemd service.
ssh in: Apr 14 20:31:05 osmc systemd[1]: Started Hyperion Systemd service.
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: Hyperion Ambilight Deamon (832)
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: Version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: Build Time: Apr 5 2018 01:57:25
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: INFO: Selected configuration file: /etc/hyperion/hyperion.config.json
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: HYPERION INFO: ColorTransform 'default' => [0; 257]
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: HYPERION INFO: ColorCorrection 'default' => [0; 257]
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: HYPERION INFO: ColorAdjustment 'default' => [0; 257]
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: LEDDEVICE INFO: configuration:
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: {
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: "colorOrder" : "rgb",
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: "delayAfterConnect" : 0,
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: "name" : "MyHyperionConfig",
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: "output" : "/dev/ttyUSB0",
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: "rate" : 115200,
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: "type" : "adalight"
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: }
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: Opening UART: /dev/ttyUSB0
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: INFO: Creating linear smoothing
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: HYPERION (CS) INFO: Created linear-smoothing(interval_ms=50;settlingTime_ms=200;updateDelay=0
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: EFFECTENGINE INFO: 27 effects loaded from directory /usr/share/hyperion/effects
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: EFFECTENGINE INFO: Initializing Python interpreter
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: INFO: Hyperion started and initialised
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: INFO: Boot sequence 'Rainbow swirl fast' EFFECTENGINE INFO: run effect Rainbow swirl fast on channel 0
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: BLACKBORDER INFO: threshold set to 0 (0)
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: BLACKBORDER INFO: mode:default
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: started
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: INFO: Json server created and started on port 19444
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: INFO: Proto server created and started on port 19445
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: DISPMANXGRABBER INFO: Display opened with resolution: 720x480
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: BLACKBORDER INFO: threshold set to 0 (0)
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: BLACKBORDER INFO: mode:default
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: INFO: Frame grabber created and started
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: terminate called after throwing an instance of 'std::runtime_error'
ssh in: Apr 14 20:31:05 osmc hyperiond[832]: what(): VIDIOC_S_STD ERROR 25, Inappropriate ioctl for device
ssh in: Apr 14 20:31:05 osmc systemd[1]: hyperion.service: Main process exited, code=killed, status=6/ABRT
ssh in: Apr 14 20:31:05 osmc systemd[1]: hyperion.service: Unit entered failed state.
ssh in: Apr 14 20:31:05 osmc systemd[1]: hyperion.service: Failed with result 'signal'.
ssh in: Apr 14 20:31:06 osmc systemd[1]: hyperion.service: Service hold-off time over, scheduling restart.
ssh in: Apr 14 20:31:06 osmc systemd[1]: Stopped Hyperion Systemd service.
ssh in: Apr 14 20:31:06 osmc systemd[1]: Started Hyperion Systemd service.
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: Hyperion Ambilight Deamon (839)
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: Version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: Build Time: Apr 5 2018 01:57:25
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: INFO: Selected configuration file: /etc/hyperion/hyperion.config.json
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: HYPERION INFO: ColorTransform 'default' => [0; 257]
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: HYPERION INFO: ColorCorrection 'default' => [0; 257]
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: HYPERION INFO: ColorAdjustment 'default' => [0; 257]
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: LEDDEVICE INFO: configuration:
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: {
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: "colorOrder" : "rgb",
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: "delayAfterConnect" : 0,
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: "name" : "MyHyperionConfig",
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: "output" : "/dev/ttyUSB0",
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: "rate" : 115200,
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: "type" : "adalight"
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: }
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: Opening UART: /dev/ttyUSB0
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: INFO: Creating linear smoothing
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: HYPERION (CS) INFO: Created linear-smoothing(interval_ms=50;settlingTime_ms=200;updateDelay=0
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: EFFECTENGINE INFO: 27 effects loaded from directory /usr/share/hyperion/effects
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: EFFECTENGINE INFO: Initializing Python interpreter
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: INFO: Hyperion started and initialised
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: INFO: Boot sequence 'Rainbow swirl fast' EFFECTENGINE INFO: run effect Rainbow swirl fast on channel 0
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: BLACKBORDER INFO: threshold set to 0 (0)
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: BLACKBORDER INFO: mode:default
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: started
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: INFO: Json server created and started on port 19444
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: INFO: Proto server created and started on port 19445
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: DISPMANXGRABBER INFO: Display opened with resolution: 720x480
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: BLACKBORDER INFO: threshold set to 0 (0)
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: BLACKBORDER INFO: mode:default
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: INFO: Frame grabber created and started
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: terminate called after throwing an instance of 'std::runtime_error'
ssh in: Apr 14 20:31:06 osmc hyperiond[839]: what(): VIDIOC_S_STD ERROR 25, Inappropriate ioctl for device
ssh in: Apr 14 20:31:06 osmc systemd[1]: hyperion.service: Main process exited, code=killed, status=6/ABRT
ssh in: Apr 14 20:31:06 osmc systemd[1]: hyperion.service: Unit entered failed state.
ssh in: Apr 14 20:31:06 osmc systemd[1]: hyperion.service: Failed with result 'signal'.
ssh in: Apr 14 20:31:06 osmc systemd[1]: hyperion.service: Service hold-off time over, scheduling restart.
ssh in: Apr 14 20:31:06 osmc systemd[1]: Stopped Hyperion Systemd service.
ssh in: Apr 14 20:31:06 osmc systemd[1]: Started Hyperion Systemd service.
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: Hyperion Ambilight Deamon (846)
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: Version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: Build Time: Apr 5 2018 01:57:25
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: INFO: Selected configuration file: /etc/hyperion/hyperion.config.json
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: HYPERION INFO: ColorTransform 'default' => [0; 257]
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: HYPERION INFO: ColorCorrection 'default' => [0; 257]
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: HYPERION INFO: ColorAdjustment 'default' => [0; 257]
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: LEDDEVICE INFO: configuration:
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: {
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: "colorOrder" : "rgb",
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: "delayAfterConnect" : 0,
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: "name" : "MyHyperionConfig",
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: "output" : "/dev/ttyUSB0",
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: "rate" : 115200,
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: "type" : "adalight"
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: }
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: Opening UART: /dev/ttyUSB0
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: INFO: Creating linear smoothing
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: HYPERION (CS) INFO: Created linear-smoothing(interval_ms=50;settlingTime_ms=200;updateDelay=0
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: EFFECTENGINE INFO: 27 effects loaded from directory /usr/share/hyperion/effects
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: EFFECTENGINE INFO: Initializing Python interpreter
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: INFO: Hyperion started and initialised
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: INFO: Boot sequence 'Rainbow swirl fast' EFFECTENGINE INFO: run effect Rainbow swirl fast on channel 0
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: BLACKBORDER INFO: threshold set to 0 (0)
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: BLACKBORDER INFO: mode:default
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: started
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: INFO: Json server created and started on port 19444
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: INFO: Proto server created and started on port 19445
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: DISPMANXGRABBER INFO: Display opened with resolution: 720x480
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: BLACKBORDER INFO: threshold set to 0 (0)
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: BLACKBORDER INFO: mode:default
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: INFO: Frame grabber created and started
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: terminate called after throwing an instance of 'std::runtime_error'
ssh in: Apr 14 20:31:06 osmc hyperiond[846]: what(): VIDIOC_S_STD ERROR 25, Inappropriate ioctl for device
ssh in: Apr 14 20:31:06 osmc systemd[1]: hyperion.service: Main process exited, code=killed, status=6/ABRT
ssh in: Apr 14 20:31:06 osmc systemd[1]: hyperion.service: Unit entered failed state.
ssh in: Apr 14 20:31:06 osmc systemd[1]: hyperion.service: Failed with result 'signal'.
ssh in: Apr 14 20:31:06 osmc systemd[1]: hyperion.service: Service hold-off time over, scheduling restart.
ssh in: Apr 14 20:31:06 osmc systemd[1]: Stopped Hyperion Systemd service.
ssh in: Apr 14 20:31:06 osmc systemd[1]: Started Hyperion Systemd service.
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: Hyperion Ambilight Deamon (853)
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: Version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: Build Time: Apr 5 2018 01:57:25
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: INFO: Selected configuration file: /etc/hyperion/hyperion.config.json
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: HYPERION INFO: ColorTransform 'default' => [0; 257]
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: HYPERION INFO: ColorCorrection 'default' => [0; 257]
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: HYPERION INFO: ColorAdjustment 'default' => [0; 257]
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: LEDDEVICE INFO: configuration:
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: {
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: "colorOrder" : "rgb",
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: "delayAfterConnect" : 0,
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: "name" : "MyHyperionConfig",
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: "output" : "/dev/ttyUSB0",
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: "rate" : 115200,
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: "type" : "adalight"
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: }
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: Opening UART: /dev/ttyUSB0
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: INFO: Creating linear smoothing
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: HYPERION (CS) INFO: Created linear-smoothing(interval_ms=50;settlingTime_ms=200;updateDelay=0
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: EFFECTENGINE INFO: 27 effects loaded from directory /usr/share/hyperion/effects
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: EFFECTENGINE INFO: Initializing Python interpreter
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: INFO: Hyperion started and initialised
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: INFO: Boot sequence 'Rainbow swirl fast' EFFECTENGINE INFO: run effect Rainbow swirl fast on channel 0
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: BLACKBORDER INFO: threshold set to 0 (0)
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: BLACKBORDER INFO: mode:default
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: started
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: INFO: Json server created and started on port 19444
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: INFO: Proto server created and started on port 19445
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: DISPMANXGRABBER INFO: Display opened with resolution: 720x480
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: BLACKBORDER INFO: threshold set to 0 (0)
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: BLACKBORDER INFO: mode:default
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: INFO: Frame grabber created and started
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: terminate called after throwing an instance of 'std::runtime_error'
ssh in: Apr 14 20:31:06 osmc hyperiond[853]: what(): VIDIOC_S_STD ERROR 25, Inappropriate ioctl for device
ssh in: Apr 14 20:31:06 osmc systemd[1]: hyperion.service: Main process exited, code=killed, status=6/ABRT
ssh in: Apr 14 20:31:06 osmc systemd[1]: hyperion.service: Unit entered failed state.
ssh in: Apr 14 20:31:06 osmc systemd[1]: hyperion.service: Failed with result 'signal'.
ssh in: Apr 14 20:31:07 osmc systemd[1]: hyperion.service: Service hold-off time over, scheduling restart.
ssh in: Apr 14 20:31:07 osmc systemd[1]: Stopped Hyperion Systemd service.
ssh in: Apr 14 20:31:07 osmc systemd[1]: hyperion.service: Start request repeated too quickly.
ssh in: Apr 14 20:31:07 osmc systemd[1]: Failed to start Hyperion Systemd service.
ssh in: Apr 14 20:31:07 osmc systemd[1]: hyperion.service: Unit entered failed state.
ssh in: Apr 14 20:31:07 osmc systemd[1]: hyperion.service: Failed with result 'signal'.
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
ssh disconnected
ssh connected
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null ; hyperion-v4l2 --device /dev/video0 --video-standard PAL --input 1 --width 1920 --height 1080 --crop-left 0 --crop-right 0 --crop-top 0 --crop-bottom 0 --size-decimator 1 --frame-decimator 2 --red-threshold 0.0 --green-threshold 0.0 --blue-threshold 0.0 --screenshot
ssh in: hyperion-v4l2:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:25
ssh out: VIDIOC_S_INPUT ERROR 22, Invalid argument
sftp getFile(./screenshot.png, java.awt.Image)
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
ssh disconnected
ssh connected
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null ; hyperion-v4l2 --device /dev/video0 --video-standard PAL --input 1 --width 1920 --height 1080 --crop-left 0 --crop-right 0 --crop-top 0 --crop-bottom 0 --size-decimator 1 --frame-decimator 2 --red-threshold 0.0 --green-threshold 0.0 --blue-threshold 0.0 --screenshot
ssh in: hyperion-v4l2:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:25
ssh out: VIDIOC_S_INPUT ERROR 22, Invalid argument
sftp getFile(./screenshot.png, java.awt.Image)
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null ; hyperion-v4l2 --device /dev/video0 --video-standard PAL --input 1 --width 1920 --height 1080 --crop-left 0 --crop-right 0 --crop-top 0 --crop-bottom 0 --size-decimator 1 --frame-decimator 2 --red-threshold 0.0 --green-threshold 0.0 --blue-threshold 0.0 --screenshot
ssh in: hyperion-v4l2:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:25
ssh out: VIDIOC_S_INPUT ERROR 22, Invalid argument
sftp getFile(./screenshot.png, java.awt.Image)
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
ssh disconnected
ssh connected
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
ssh out: hyperion-remote -u 1.0 -m 1.0 -n 0.1 -g "2.5 2.5 2.5" -t "0.0 0.0 0.0" -R "255 0 0" -G "0 255 0" -B "0 0 255" -Z "255 255 255"
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
ssh out: hyperion-remote -u 1.0 -m 1.0 -n 0.1 -g "2.5 2.5 2.5" -t "0.0 0.0 0.0" -R "255 0 0" -G "0 255 0" -B "0 0 255" -Z "255 255 255"
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
ssh out: hyperion-remote -u 1.0 -m 1.0 -n 0.1 -g "2.5 2.5 2.5" -t "0.0 0.0 0.0" -R "255 0 0" -G "0 255 0" -B "0 0 255" -Z "255 255 255"
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
ssh disconnected
ssh connected
sftp Send Hyperion Config - Sourcepath: C:/Users/lebed/Desktop, Targetpath: /etc/hyperion/, Filename: hyperion.config.json
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: hyperion-remote -c 30ff2a
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
ssh out: hyperion-remote -c 30ff29
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
ssh out: hyperion-remote -c 30ff29
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
ssh out: hyperion-remote -c 30ff29
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
ssh out: hyperion-remote -c 30ff29
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
ssh out: hyperion-remote -c 30ff29
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
ssh out: hyperion-remote -c 30ff29
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
ssh out: hyperion-remote -c 30ff29
ssh in: hyperion-remote:
ssh in: version : V1.03.4 (brindosch-c750c41/dc6a602-1522918225
ssh in: build time: Apr 5 2018 01:57:05
ssh out: Unable to connect to host
Alles anzeigen