Wie versorgst du den Grabber mit Strom?
Siehst du etwas im Hyperion Debug log?
Wenn der neu starten würde ist das im log zu sehen.
gruß pclin
Wie versorgst du den Grabber mit Strom?
Siehst du etwas im Hyperion Debug log?
Wenn der neu starten würde ist das im log zu sehen.
gruß pclin
Bei deinen Einstellungen für den Grabber:
Stelle auf MJPG
Bildverkleinerungs Faktor zwischen 4 und 8
Der Wert für Hardware-Farbtonsteuerung ist sehr ungewöhnlich, normalerweise steht der bei einem Grabber mit Macrosilicon Chip auf 0.
gruß pclin
Die Bildschirmaufnahme funktioniert nicht bei DRM geschützten Inhalt.
Über den USB Grabber sollte das funktionieren weil dann ein Bild von Netflix am Grabber ankommt.
Flackern kann durch fehlenden Gemeinsamen Ground, durch Einstreuungen auf der Data Line oder auch durch Defekte Hardware, falsche Einstellungen entstehen.
Wie ist das Live Video in Hyperion flackert es dort auch?
Hast du den Grabber an einem anderen Gerät getestet (z.B. PC mit VLC)?
gruß pclin
For ws281x, Hyperion must run with root privileges. You can find all other settings here in the thread.
sudo updateHyperionUser -u root
regards pclin
This will be a loop out grabber, power supply or usb cable <-> ethernet extender <-> usb cable problem.
The message "The video recording device is no longer present" only appears if there is no longer a device in the OS.
Before you restart Hyperion, check if the device is present.
usb-devices | grep uvc
On the Windows PC, check with VLC to see if there are dropouts.
phone chargers are usually not suitable, phone chargers usually communicate with smartphones and adapt to them.
regards pclin
All 3 options work. If there is no LED in the corner, this is usually not noticeable, unless the edge gap is too large and the distance between the LED and the wall is very small.
The layout in Hyperion must match your installation.
Counting begins at the top left.
Reverse direction should be avoided.
If you don't have any LED in the corners you can adjust Edge Gap.
I prefer the bottom middle as a starting point (5 stripes parts), Screenshot LED-Layout-65
regards pclin
LED Typ, PSU, wirering
1280x720 60 FPS, NV12 is too much for RPI, and also not necessary!
Screenshot of your LED layout.
Your pictures are not suitable for an assessment of your problem!
Something is still wrong, compare your picture with mine.
regards pclin
Everything can be calculated here.
LED power consumption:
Recommended minimal wire crosssection:
Fuse:
Total voltage drop (wire + fuse):
1mm2 to the LED is usually sufficient with a correspondingly short supply line. Cables should always be as short as possible.
regards pclin
Have you tested the grabber on another device, e.g. a PC?
There is no grabber listed in the system (OS), so you cannot select it in Hyperion.
regards pclin
Internal apps like Netflix don't work because of DRM.
Set PicCap as in the screenshot.
regards pclin
You need a power supply for the LEDs and a level shifter + resistor.
ESP maximum output is 750mA!
regards pclin
Laut log sollte der Grabber funktionieren.
In deinem ersten Post schreibst du
Zitat von MiillerHeute habe ich einen alten Laptop von 2014 per HDMI an meinen Splitter gehängt, und es funktioniert auch nicht.
das lässt ja auch vermuten das mit dem Splitter etwas sein könnte.
Splitter für einige Zeit vom Strom nehmen, dann neu starten.
Netzteil auch aus stecken, wenn möglich austauschen (gleiche Voltzahl, mind. soviel Ampere wie Orginal)
Versorge mal den Grabber mit Signal ohne den Splitter, hast du dann ein Bild In Hyperion und die LED leuchten bist du etwas weiter.
gruß pclin
If the libraries are available on the LG, the PicCap backends could work, I would then test them.
You can also create a config.json for PicCap without the PicCap GUI.
With RPI, splitter and external grabber you get external sources to shine with Ambilight. But PicCap and Hyperion on the LG is the better solution.
regards pclin
The backends should work for PicCap.
ls /usr/lib |grep libvt
regards pclin
As far as I know, that won't work.
kernel, core_os and webos do not fit.
regards pclin
You can run Hyperion on a PC, RPI Dreambox etc. with an external digital grabber.
New LG TVs can still be rooted, there is also a method for the new WebOS versions.
From Webos 22 you have to get SSH running again, there are instructions for that too.
My old TV from 2017 works with PicCap and Hyperion, there are 2 versions "core_os_release" and "webos_manufacturing_version"
With grep -h -E '"(hardware_id|core_os_release|product_id|webos_manufacturing_version|board_type)"' /var/run/nyx/* can you read them when you access the TV via telnet or ssh.
regards pclin
Hyperion liest die Daten aus dem System aus, in früheren Versionen konnte man dort etwas einstellen auch wenn es nicht unterstützt wurde, verwendet wurde dann aber was vorhanden war/ist.
Bei den meisten Grabbern geht MJPEG und YUYV.
Wenn dir nur YUYV angeboten wird kann der Grabber nichts anderes.
Überprüfen kannst du das auch selber mit v4l2-ctl --list-formats-ext da wird die alles angezeigt was der Grabber wirklich kann.
Der Analog/Digital Wandler und analoge Grabber sollte zwar funktionieren, ist aber nicht mehr zu empfehlen.
Der Wandler wird nicht mehr benötigt bei Verwendung eines digitalen Grabbers für 10€. Bessere Qualität, UHD möglich am Eingang des Grabbers und weniger Fehlerquellen.
Ein Hyperion Protokoll Einstellungsstufe Debug, Einstellungsstufe Expert wäre gut.
Und die Ausgaben von
usb-devices
v4l2-ctl --all
v4l2-ctl --list-formats-ext
Teste den Grabber auch am PC mit VLC, wenn der dort einwandfrei funktioniert sollte das auch mit Hyperion gehen.
gruß pclin
In the WLED WebUI you set the led strip. LED number and color order. In the Hyperion WebUI, choose wled.
LG
Justscan On
regards pclin
Select Led Output > Controller type: wled. Create LED layout.
Test if you can use colors and effects.
In PicCap see screenshot.
backends can be different depending on the age of the TV.
regards pclin
Bei Bildverarbeitung > Glättung
gruß pclin