Why an older HyperBian?
regards pclin
Why an older HyperBian?
regards pclin
Hyperion sends data to the ESP with WLED, which calculates the values for the LED from the data, which are then controlled via the ESP's GPIO. PicCap (grabber) runs on LG TV and sends images to Hyperion via flat buffer. It is best if you also use Hyperion on the LG.
Hyperion can also run on a PC (Windows, Mac, Linux), RPI, Dreambox, etc.
For ESP, there are all imaginable versions, from tinkering solutions to ready-made systems (ESP flashed in housing with stripes, PSU).
See WLED Wiki Compatible Hardware, wled.shop, insanelights, QuinLED etc.
regards pclin
LEDs cannot be connected directly to the LG.
The best and easiest is an ESP with WLED software.
ESP32 is the best option, it can be controlled via WLAN, but an ESP with a LAN interface is the better choice for the lowest latency.
Wled software can be flashed very easily and is also quickly set up in the WIKI you will find everything about it.
regards pclin
Ist zwar nicht Amazon
Auf Amazon aber 8x teurer und für Ambilight am RPI eigentlich nicht nötig
gruß pclin
Teste den Grabber am PC oder Odroid, so kannst du feststellen ob es am Grabber oder RPI liegt.
gruß pclin
Ja hat beides.
gruß pclin
Zur Zeit wohl nur über AliExpress.
gruß pclin
QuinLED ist ein gutes Produkt.
Du kannst dir entweder etwas Drucken oder Drucken lassen.
Verteilerdosen aus dem Baumarkt verwenden.
usw.
gruß pclin
Da habe ich leider auch keine Idee was da falsch läuft.
Wenn du aber nur Effekte nutzen möchtest wäre ein ESP mit WLED Software die bessere Wahl.
ESP kostet ab 5,- €.
WLED bringt über 100 Effekte, 50 Farbpaletten und Optimale Einstellungen für Sk6812.
Wled auf den ESP Flashen, Data an GPIO 2 anschliessen, Masse und +5V vom Netzteil der Stripes anschliessen und Effekte geniessen.
EDIT:Wenn du dann doch auch Ambilight verwenden möchtest kannst du Hyperion verwenden und
Steuerungstyp: wled einstellen
Weitere ist dann nicht zu tun.
Weiterer Vorteil Hyperion kann dann z.B auf einem PC, RPI, LG TV, Dreambox usw. laufen.
gruß pclin
Vermutlich nicht, im Live Video kannst du das beobachten.
Meistens liegt es am fehlender gemeinsamen Masse., oder Einstreuungen auf die Data Line.
gruß pclin
Auch bei Effekt leuchtet nichts?
Live-Video siehe Screenshot.
gruß pclin
1. Bei Wlan Ansteuerung etwa 5 ms, mit LAN Ansteuerung 0,5 ms
2. Ich empfehle ESP32 mit LAN Schnittstelle, im WLED-Wiki unter Compatible Hardare findest du Infos zu den Geräten.
SK6812
1. RGBW-NW ist die neutrale Version, CW bläulich, WW gelblich.
2. Ist besser mit Levelshifter und 62 Ohm Widerstand.
gruß pclin
WLED hat einige Einstellungen für SK6812 RGBW.
gruß pclin
Leuchten die LED's bei Effekten?
Gibt es ein ein Live Video in Hyperion?
Was steht im Protokoll Stufe Debug?
Läuft dein Hyperion unter root?
sudo updateHyperionUser -u root
gruß pclin
With USB Serial, WLED uses the arduino protocol, but the baud rate is limited. Higher baud rates can be used with Hyperserial.
regards pclim
regards pclin
Arduino is not a good choice, not enough power (CPU, RAM).
For SK6812 RGBW, ESP32 and WLED is more suitable.
regards pclin