Das wäre natürlich absolut großartig. Wie kommen wir zusammen bzw. wie kann ich das dann wieder gut machen?
wollt dir grad ne DM schreiben das funktioniert aber irgendwie nicht.. kannst du mich anschreiben?
Das wäre natürlich absolut großartig. Wie kommen wir zusammen bzw. wie kann ich das dann wieder gut machen?
wollt dir grad ne DM schreiben das funktioniert aber irgendwie nicht.. kannst du mich anschreiben?
@Paulchen-Panther & @Portisch gibt es Hoffnung für das Problem mit dem externen Grabber bei CoreElec und Hyperion.NG?
https://discourse.coreelec.org…bber-no-dev-video0/775/35
@Portisch
Kennst du eine günstige (muss nicht das neuste sein) CoreElec Box die ich mir zulegen könnte, um bei der Programmierung der fertigen Packages zu helfen?
Falls es hilft würde ich die CoreElec Box beisteuern
post hyperion log & hyperion.config.json please
is dtparam=spi=on in the /flash/config.txt enabled?
But as for a normal MKV/M2TS movie with black borders doesn't seem to give ambilight.
Try changing the threshold/mode in the Blackborder settings.
https://hyperion-project.org/wiki/Blackborder-Detection-Mode
https://hyperion-project.org/w…order-Detection-Threshold
Hi, what does mean "preinstalled image"? Newly downloaded image of raspbian?
I have same problem with raspbian (RPi3) and hyperion: "hyperion.service: main process exited, code=killed, status=11/SEGV"
plz run:
and then start the command of the output manually...
for example
/opt/hyperion/bin/hyperiond /opt/hyperion/config/hyperion.config.json
/usr/share/hyperion/hyperiond /etc/hyperion/hyperion.config.json
and post the output
Comments? I see no comments. The only Thing I changed in this firmware is the PIN. Which is pin 7 for me.
Anyway I tried the firmware and no change whatsoever.
in the sketch you must also change:
// type of your led controller, possible values, see below
#define LED_TYPE WS2812B to #define LED_TYPE WS2811
and #define MAX_LEDS 500 to #define MAX_LEDS 228 (the number of your leds)
change the type in hyperion.config.json from "type" : "AdalightApa102", to "type" : "adalight",
when you start hyperion the lights light up during initialization?
can you post your hyperion.config.json?
the following points are activated in kodi?
"Allow remote control by programs on this system"
"Allow remote control by programs on other systems"
Alles anzeigenComments? I see no comments. The only Thing I changed in this firmware is the PIN. Which is pin 7 for me.
Anyway I tried the firmware and my leds didn't go on at all with this on.
This is what the log of Hyper says.
ssh in: Opening UART: /dev/ttyUSB0
ssh in: Unable to open RS232 device (IO Exception (2): No such file or directory, file /home/sascha/hyperion/dependencies/build/serial/src/impl/unix.cc, line 100.)
ssh in: INFO: Creating linear smoothing
ssh in: HYPERION (CS) INFO: Created linear-smoothing(interval_ms=50;settlingTime_ms=200;updateDelay=0
ssh in: EFFECTENGINE INFO: 27 effects loaded from directory /storage/hyperion/effects
ssh in: EFFECTENGINE INFO: Initializing Python interpreter
ssh in: INFO: Hyperion started and initialised
ssh in: terminate called after throwing an instance of 'std::runtime_error'
ssh in: what(): JSONSERVER ERROR: could not bind to port
ssh in: Aborted (core dumped)
ssh in: Device unblocked
ssh in: Opening UART: /dev/ttyUSB0
ssh in: Unable to open RS232 device (IO Exception (2): No such file or directory, file /home/sascha/hyperion/dependencies/build/serial/src/impl/unix.cc, line 100.)
ssh in: Device blocked for 3000 ms
ssh in: Device unblocked
ssh in: Opening UART: /dev/ttyUSB0
ssh in: Unable to open RS232 device (IO Exception (2): No such file or directory, file /home/sascha/hyperion/dependencies/build/serial/src/impl/unix.cc, line 100.)
ssh in: Device blocked for 3000 ms
plz post the output from
and
plug the device out and write
and then plug it in and write
and post the output
why you are use the usb video grabber?
if there is no external video source(only the rapsberry pi) you can use the internal framegrabber
...the usb grabber,hdmi splitter and RCA to HDMI are not needed...
funktionieren sollte beides...
mit der 127.0.0.1 bist du aber auf der sicheren Seite und kannst dir Anpassungen bei z.B. Änderung der IP Adresse ersparen...
Wurde gefixt. Danke fürs Melden.
Ich werde mir was überlegen, damit das nicht mehr passiert.
Grüße
brindosch
am einfachsten ist der url redirect...;)
Das Zertifikat für https://hyperion-project.org ist ok...
Aber das Zertifikat für die www Subdomain https://www.hyperion-project.org ist nicht mehr gültig...
bitte mal die config posten...
Zitatssh in: KODICHECK ERROR: Kodi Connection error (0)
die beiden Punkte Fernsteuerung durch Programme auf diesem Rechner zulassen & Fernsteuerung durch Programme auf anderen Rechnern zulassen sind in Kodi aktiv ?
Kannst du mir auch bei dem Grabberproblem helfen? :):)
Poste bitte deine Konfig und das dazugehörige Hyperion Logfile in der beide Grabber enthalten sind.
Setz bitte mal die priority deines grabber-v4l2 auf 900 (default-Wert).
kannst du bitte einen Screenshot von Hypercon im Grabber-Tab machen nachdem du dort ein Bild vom Grabber geholt hast
hört sich so an als ob du zwei Netzteile nutzt?!?
wenn ja bitte überprüfen ob der RPI das selbe Massepotential(GND) wie die LED´s haben
um zwischen Kodi und Grabber automatisch umzuschalten am besten mit einer Konfig-Datei arbeiten in der grabber-v4l2 und xbmcVideoChecker Part enthalten sind.
funktioniert wunderbar seit https://github.com/hyperion-project/hyperion/issues/306
Beim Kodi Checker dann die beiden Einträge auf false Stellen
Und auf die Priorität der jeweiligen grabber achten.
ein Ausschnitt meiner Konig:
"framegrabber" :
{
"width" : 64,
"height" : 64,
"frequency_Hz" : 10.0,
"priority" : 890
},
"xbmcVideoChecker" :
{
"xbmcAddress" : "127.0.0.1",
"xbmcTcpPort" : 9090,
"grabVideo" : true,
"grabPictures" : true,
"grabAudio" : true,
"grabMenu" : false,
"grabPause" : false,
"grabScreensaver" : true,
"enable3DDetection" : true
},
"jsonServer" :
{
"port" : 19444
},
"protoServer" :
{
"port" : 19445
},
"grabber-v4l2" :
{
"device" : "/dev/video0",
"input" : 0,
"standard" : "PAL",
"width" : -1,
"height" : -1,
"frameDecimation" : 2,
"sizeDecimation" : 8,
"priority" : 900,
"mode" : "2D",
"cropLeft" : 20,
"cropRight" : 5,
"cropTop" : 12,
"cropBottom" : 4,
"redSignalThreshold" : 0.0,
"greenSignalThreshold" : 0.0,
"blueSignalThreshold" : 0.0
},
Alles anzeigen