To anyone wondering what happened, turns out the grabber itself was working fine and was mounted to /dev/video0. The reason the LEDs weren't reacting to any image was because of a setting in Hyperion. On the grabber tab, I had to change the image format to NTSC instead of PAL. The PAL setting was causing the Hyperion software to freeze when taking a grabber screenshot. After changing the setting and re-uploading the configuration, I was able to take grabber screenshots and adjust the crop of the screen to figure out the direction the LEDs must be placed.
Beiträge von Noah
-
-
Hello,
I have a "Easier Cap" utv007 chipset usb video grabber plugged into my Raspberry Pi 3 Model B. If I type in lsusb, it's listed as ID 1b71:3002. The problem here is the device is called /dev/v4l instead of /dev/video0. I tried changing the device in Hyperion to the actual name of the device, but it still wouldn't load. Is there a way I can either get hyperion to work with /dev/v4l or a way I can make the device mount to /dev/video0?
Thanks ahead of time,
Noah
-
I got the LEDs to react to the phone app!! It's amazing! Now, I just need help getting them to react to either the internal grabber, or the GrabberV4l2. I can't seem to get either working, it still displays a grey screen when I "take a grabber screenshot" when trying to use the internal.
Then when I select the Grabber V4I2, the LEDs won't react at all.
Thanks again for the help!
I'm trying to start with the internal grabber. When I try to take a grabber screenshot... it takes forever to load and never shows the screenshot. Any news on this? -
great, the wago and the wires was maybe to long so the data get lost...
so and now install hyperion with this please
I got the LEDs to react to the phone app!! It's amazing! Now, I just need help getting them to react to either the internal grabber, or the GrabberV4l2. I can't seem to get either working, it still displays a grey screen when I "take a grabber screenshot" when trying to use the internal.Then when I select the Grabber V4I2, the LEDs won't react at all.
Thanks again for the help!
-
yes, on the interface picture is spi used, so spi should work if the screen works... can you use a short wire and shortcut the two pins with your hand? test is just a few seconds should be no porblem to hold them
-
mh looks like your spi pins are damaged...
I don't like the sound of that..I followed this guide with the same result.
Is there anyway it could be the cables or Wago connector I'm using?
I also have
that plugs in to the GPIO on the board. After the driver is configured, it works perfectly. Would that rule out that the spi pins are damaged? -
I switched the cables so that they were in pins 19 and 21 and received the same results as above..
-
doesnt look good... is spi active?can you post the output from "ls /dev"
-
should be ok, just give it a try
Here are my results and a picture of the connection.pi@raspberrypi:~ $ wget https://raw.githubusercontent.…ntation/spi/spidev_test.c
--2017-01-17 17:22:15-- https://raw.githubusercontent.…ntation/spi/spidev_test.c
Resolving raw.githubusercontent.com (raw.githubusercontent.com)... 151.101.44.133
Connecting to raw.githubusercontent.com (raw.githubusercontent.com)|151.101.44.133|:443... connected.
HTTP request sent, awaiting response... 200 OK
Length: 4410 (4.3K) [text/plain]
Saving to: ‘spidev_test.c’spidev_test.c 100%[=====================>] 4.31K --.-KB/s in 0s
2017-01-17 17:22:16 (10.2 MB/s) - ‘spidev_test.c’ saved [4410/4410]
pi@raspberrypi:~ $ gcc -o spidev_test spidev_test.c
pi@raspberrypi:~ $ ./spidev_test -D /dev/spidev0.0
spi mode: 0
bits per word: 8
max speed: 500000 Hz (500 KHz)00 00 00 00 00 00
00 00 00 00 00 00
00 00 00 00 00 00
00 00 00 00 00 00
00 00 00 00 00 00
00 00 00 00 00 00
00 00EDIT: I realize now that the connections are in pin 19 and 23, which would be the reason for the Loopback test not showing anything.. But would that be the reason this isn't working? The video and tutorial on here that I have referenced had the cables connect to pins 19 and 23..
I will attempt the loopback test again with the cables plugged into the correct pins (19 and 21) later tonight.
-
just the loopback test, there you can see if the pins are working correct
Okay that makes more sense. It looks like it wants a wire between pin 19 and pin 21. I don't have female to female jumper wire so would it work if I run two cables (each with the male jumper connector stripped) through one of the Wago Connectors I have linked to in my original post? -
what was the output? or didnt you do it?
I didn't do it at all. Do I do everything listed on the page or just the Loopback Test? -
I freshly installed the Raspbian Jessie with Pixel image from here. So far no luck with just the image. I'm a bit confused with the spi-test part..
This is setup so far to use an internal grabber, so I don't have the rest of the rig plugged in, just the Pi and the LEDs. I tried to take a screenshot of what the grabber was displaying but it only turned out to be grey.
[SPOILER="SSH Log From installing, starting Hyperion"]
SSH Traffic:
ssh connected
ssh out: cd /tmp && wget -nv -N https://raw.github.com/hyperio…r/bin/install_hyperion.sh && chmod +x install_hyperion.sh && sudo sh ./install_hyperion.sh HyperConInstall ; rm install_hyperion.sh
ssh out: Last-modified header missing -- time-stamps turned off.
ssh out: 2017-01-17 02:04:07 URL:https://raw.githubusercontent.…r/bin/install_hyperion.sh [14539/14539] -> "install_hyperion.sh" [1]
ssh in: *******************************************************************************
ssh in: This script will install/update Hyperion Ambient Light
ssh in: Created by brindosch - hyperion-project.org - the official Hyperion source.
ssh in: *******************************************************************************
ssh in: ---> Stop Hyperion, if necessary
ssh in: ---> Install/Update Hyperion dependencies (This may take a while)
ssh in: ---> Raspberry Pi found, but SPI is not set, we write "dtparam=spi=on" to /boot/config.txt
ssh in: ---> Downloading the appropriate Hyperion release
ssh out: 2017-01-17 02:06:25 URL:https://superb-sea2.dl.sourcef…ease/hyperion_rpi2.tar.gz [1637006/1637006] -> "-" [1]
ssh in: ---> Installing systemd script
ssh in: ---> Starting Hyperion
ssh in: *******************************************************************************
ssh in: Hyperion Installation/Update finished!
ssh in: Please download the latest HyperCon version to benefit from new features!
ssh in: To create a config, follow the HyperCon Guide at our Wiki (EN/DE)!
ssh in: Wiki: wiki.hyperion-project.org Webpage: www.hyperion-project.org
ssh in: *******************************************************************************
ssh in: Rebooting now, we added dtparam=spi=on to config.txt
ssh disconnected
ssh connected
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null ; hyperion-v4l2 --device /dev/video0 --video-standard PAL --input 0 --width -1 --height -1 --crop-left 0 --crop-right 0 --crop-top 0 --crop-bottom 0 --size-decimator 1 --frame-decimator 2 --red-threshold 0.0 --green-threshold 0.0 --blue-threshold 0.0 --screenshot
ssh in: hyperion-v4l2:
ssh in: version : V1.03.2 (brindosch-99d9396/d3713a8-1469452981
ssh in: build time: Jul 25 2016 06:54:40
ssh in: V4L2GRABBER INFO: width=720 height=576
ssh in: V4L2GRABBER INFO: pixel format=YUYV
ssh in: V4L2GRABBER INFO: signal threshold set to: {0,0,0}
ssh in: V4L2GRABBER INFO: started
ssh in: V4L2GRABBER INFO: stopped
sftp getFile(./screenshot.png, java.awt.Image)
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
ssh out: sudo systemctl stop hyperion.service 2>/dev/null; sudo /etc/init.d/hyperion stop 2>/dev/null ; sudo /sbin/initctl stop hyperion 2>/dev/null
ssh out: sudo systemctl start hyperion.service 2>/dev/null ; sudo /etc/init.d/hyperion start 2>/dev/null ; sudo /sbin/initctl start hyperion 2>/dev/null
[/SPOILER]
// Automatically generated configuration file for Hyperion ambilight daemon
// Notice: All values are explained with comments at our wiki: wiki.hyperion-project.org (config area)
// Generated by: HyperCon (The Hyperion deamon configuration file builder)
// Created with HyperCon V1.03.1 (11.06.2016){
// DEVICE CONFIGURATION
"device" :
{
"name" : "MyHyperionConfig",
"type" : "apa102",
"output" : "/dev/spidev0.0",
"rate" : 1000000,
"colorOrder" : "rgb"
},// COLOR CALIBRATION CONFIG
"color" :
{
"channelAdjustment" :
[
{
"id" : "default",
"leds" : "*",
"pureRed" :
{
"redChannel" : 255,
"greenChannel" : 0,
"blueChannel" : 0
},
"pureGreen" :
{
"redChannel" : 0,
"greenChannel" : 255,
"blueChannel" : 0
},
"pureBlue" :
{
"redChannel" : 0,
"greenChannel" : 0,
"blueChannel" : 255
}
}
],
"temperature" :
[
{
"id" : "default",
"leds" : "*",
"correctionValues" :
{
"red" : 255,
"green" : 255,
"blue" : 255
}
}
],
"transform" :
[
{
"id" : "default",
"leds" : "*",
"hsl" :
{
"saturationGain" : 1.0000,
"luminanceGain" : 1.0000,
"luminanceMinimum" : 0.0000
},
"red" :
{
"threshold" : 0.0000,
"gamma" : 2.5000
},
"green" :
{
"threshold" : 0.0000,
"gamma" : 2.5000
},
"blue" :
{
"threshold" : 0.0000,
"gamma" : 2.5000
}
}
],
// SMOOTHING CONFIG
"smoothing" :
{
"type" : "linear",
"time_ms" : 200,
"updateFrequency" : 30.0000,
"updateDelay" : 0
}
},// NO V4L2 GRABBER CONFIG
// FRAME GRABBER CONFIG
"framegrabber" :
{
"width" : 64,
"height" : 64,
"frequency_Hz" : 10.0,
"priority" : 890
},// BLACKBORDER CONFIG
"blackborderdetector" :
{
"enable" : true,
"threshold" : 0.0,
"unknownFrameCnt" : 600,
"borderFrameCnt" : 50,
"maxInconsistentCnt" : 10,
"blurRemoveCnt" : 1,
"mode" : "default"
},// BOOTEFFECT CONFIG
"bootsequence" :
{
"color" : [0,0,0],
"effect" : "Rainbow swirl fast",
"duration_ms" : 3000,
"priority" : 700
},// JSON SERVER CONFIG
"jsonServer" :
{
"port" : 19444
},// PROTO SERVER CONFIG
"protoServer" :
{
"port" : 19445
},// EFFECT PATH
"effects" :
{
"paths" :
[
"/storage/hyperion/effects",
"/usr/share/hyperion/effects"
]
},// NO KODI CHECK CONFIG
// NO BOBLIGHT SERVER CONFIG
// NO JSON/PROTO FORWARD CONFIG// LED CONFIGURATION
"leds" :
[
{
"index" : 0,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0323 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 1,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.9333, "maximum" : 1.0000 }
},
{
"index" : 2,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.8667, "maximum" : 0.9333 }
},
{
"index" : 3,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.8000, "maximum" : 0.8667 }
},
{
"index" : 4,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.7333, "maximum" : 0.8000 }
},
{
"index" : 5,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.6667, "maximum" : 0.7333 }
},
{
"index" : 6,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.6000, "maximum" : 0.6667 }
},
{
"index" : 7,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.5333, "maximum" : 0.6000 }
},
{
"index" : 8,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.4667, "maximum" : 0.5333 }
},
{
"index" : 9,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.4000, "maximum" : 0.4667 }
},
{
"index" : 10,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.3333, "maximum" : 0.4000 }
},
{
"index" : 11,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.2667, "maximum" : 0.3333 }
},
{
"index" : 12,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.2000, "maximum" : 0.2667 }
},
{
"index" : 13,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.1333, "maximum" : 0.2000 }
},
{
"index" : 14,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.0667, "maximum" : 0.1333 }
},
{
"index" : 15,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0500 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0667 }
},
{
"index" : 16,
"hscan" : { "minimum" : 0.0000, "maximum" : 0.0323 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 17,
"hscan" : { "minimum" : 0.0323, "maximum" : 0.0645 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 18,
"hscan" : { "minimum" : 0.0645, "maximum" : 0.0968 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 19,
"hscan" : { "minimum" : 0.0968, "maximum" : 0.1290 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 20,
"hscan" : { "minimum" : 0.1290, "maximum" : 0.1613 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 21,
"hscan" : { "minimum" : 0.1613, "maximum" : 0.1935 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 22,
"hscan" : { "minimum" : 0.1935, "maximum" : 0.2258 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 23,
"hscan" : { "minimum" : 0.2258, "maximum" : 0.2581 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 24,
"hscan" : { "minimum" : 0.2581, "maximum" : 0.2903 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 25,
"hscan" : { "minimum" : 0.2903, "maximum" : 0.3226 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 26,
"hscan" : { "minimum" : 0.3226, "maximum" : 0.3548 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 27,
"hscan" : { "minimum" : 0.3548, "maximum" : 0.3871 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 28,
"hscan" : { "minimum" : 0.3871, "maximum" : 0.4194 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 29,
"hscan" : { "minimum" : 0.4194, "maximum" : 0.4516 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 30,
"hscan" : { "minimum" : 0.4516, "maximum" : 0.4839 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 31,
"hscan" : { "minimum" : 0.4839, "maximum" : 0.5161 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 32,
"hscan" : { "minimum" : 0.5161, "maximum" : 0.5484 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 33,
"hscan" : { "minimum" : 0.5484, "maximum" : 0.5806 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 34,
"hscan" : { "minimum" : 0.5806, "maximum" : 0.6129 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 35,
"hscan" : { "minimum" : 0.6129, "maximum" : 0.6452 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 36,
"hscan" : { "minimum" : 0.6452, "maximum" : 0.6774 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 37,
"hscan" : { "minimum" : 0.6774, "maximum" : 0.7097 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 38,
"hscan" : { "minimum" : 0.7097, "maximum" : 0.7419 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 39,
"hscan" : { "minimum" : 0.7419, "maximum" : 0.7742 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 40,
"hscan" : { "minimum" : 0.7742, "maximum" : 0.8065 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 41,
"hscan" : { "minimum" : 0.8065, "maximum" : 0.8387 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 42,
"hscan" : { "minimum" : 0.8387, "maximum" : 0.8710 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 43,
"hscan" : { "minimum" : 0.8710, "maximum" : 0.9032 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 44,
"hscan" : { "minimum" : 0.9032, "maximum" : 0.9355 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 45,
"hscan" : { "minimum" : 0.9355, "maximum" : 0.9677 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 46,
"hscan" : { "minimum" : 0.9677, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0800 }
},
{
"index" : 47,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.0000, "maximum" : 0.0667 }
},
{
"index" : 48,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.0667, "maximum" : 0.1333 }
},
{
"index" : 49,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.1333, "maximum" : 0.2000 }
},
{
"index" : 50,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.2000, "maximum" : 0.2667 }
},
{
"index" : 51,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.2667, "maximum" : 0.3333 }
},
{
"index" : 52,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.3333, "maximum" : 0.4000 }
},
{
"index" : 53,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.4000, "maximum" : 0.4667 }
},
{
"index" : 54,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.4667, "maximum" : 0.5333 }
},
{
"index" : 55,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.5333, "maximum" : 0.6000 }
},
{
"index" : 56,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.6000, "maximum" : 0.6667 }
},
{
"index" : 57,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.6667, "maximum" : 0.7333 }
},
{
"index" : 58,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.7333, "maximum" : 0.8000 }
},
{
"index" : 59,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.8000, "maximum" : 0.8667 }
},
{
"index" : 60,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.8667, "maximum" : 0.9333 }
},
{
"index" : 61,
"hscan" : { "minimum" : 0.9500, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.9333, "maximum" : 1.0000 }
},
{
"index" : 62,
"hscan" : { "minimum" : 0.9677, "maximum" : 1.0000 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 63,
"hscan" : { "minimum" : 0.9355, "maximum" : 0.9677 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 64,
"hscan" : { "minimum" : 0.9032, "maximum" : 0.9355 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 65,
"hscan" : { "minimum" : 0.8710, "maximum" : 0.9032 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 66,
"hscan" : { "minimum" : 0.8387, "maximum" : 0.8710 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 67,
"hscan" : { "minimum" : 0.8065, "maximum" : 0.8387 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 68,
"hscan" : { "minimum" : 0.7742, "maximum" : 0.8065 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 69,
"hscan" : { "minimum" : 0.7419, "maximum" : 0.7742 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 70,
"hscan" : { "minimum" : 0.7097, "maximum" : 0.7419 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 71,
"hscan" : { "minimum" : 0.6774, "maximum" : 0.7097 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 72,
"hscan" : { "minimum" : 0.6452, "maximum" : 0.6774 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 73,
"hscan" : { "minimum" : 0.6129, "maximum" : 0.6452 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 74,
"hscan" : { "minimum" : 0.5806, "maximum" : 0.6129 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 75,
"hscan" : { "minimum" : 0.5484, "maximum" : 0.5806 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 76,
"hscan" : { "minimum" : 0.5161, "maximum" : 0.5484 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 77,
"hscan" : { "minimum" : 0.4839, "maximum" : 0.5161 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 78,
"hscan" : { "minimum" : 0.4516, "maximum" : 0.4839 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 79,
"hscan" : { "minimum" : 0.4194, "maximum" : 0.4516 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 80,
"hscan" : { "minimum" : 0.3871, "maximum" : 0.4194 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 81,
"hscan" : { "minimum" : 0.3548, "maximum" : 0.3871 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 82,
"hscan" : { "minimum" : 0.3226, "maximum" : 0.3548 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 83,
"hscan" : { "minimum" : 0.2903, "maximum" : 0.3226 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 84,
"hscan" : { "minimum" : 0.2581, "maximum" : 0.2903 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 85,
"hscan" : { "minimum" : 0.2258, "maximum" : 0.2581 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 86,
"hscan" : { "minimum" : 0.1935, "maximum" : 0.2258 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 87,
"hscan" : { "minimum" : 0.1613, "maximum" : 0.1935 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 88,
"hscan" : { "minimum" : 0.1290, "maximum" : 0.1613 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 89,
"hscan" : { "minimum" : 0.0968, "maximum" : 0.1290 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 90,
"hscan" : { "minimum" : 0.0645, "maximum" : 0.0968 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
},
{
"index" : 91,
"hscan" : { "minimum" : 0.0323, "maximum" : 0.0645 },
"vscan" : { "minimum" : 0.9200, "maximum" : 1.0000 }
}
],"endOfJson" : "endOfJson"
} -
personal experience: can you try it first with raspbian, and if its not working on raspbian please do the spi-test
https://www.raspberrypi.org/do…README.md#troubleshooting
Thanks for the reply!I actually originally had Raspbian installed but it did not work. I installed OSMC because that's what the guide that I linked to was setting up. I will try again with Raspbian and run the spi-test when I'm home in about five hours.
-
Hello!
Thanks for any help you might be able to provide me.
I'm fairly new to the Raspberry Pi and very new to working with LEDs and electrical wiring like this. My girlfriend actually bought me the parts for this project for Christmas, but I haven't been able to get it working. I've looked through the tutorial posted here. I have also used the YouTube video made by GreatScott as a guide for myself.
I have everything wired up behind the TV, OSMC installed on my Raspberry Pi 3 Model B, and Hyperion configured to match my setup. My problem is when I finally get the config sent over to the Pi through SSH and select Start the LEDs don't react - nothing happens.
I have this setup to use my Chromecast as the display (thus why all the extra hardware) that the LEDs will react to. Of course I have tried this with the internal display grabber to no avail as well.
I have everything already setup and hooked up (I think correctly). I used the extra jumper cables to solder the LEDs together as well as hooked them up into the DC adapter to power the LEDs (not sure if that is where I went wrong?)
The wiring is hooked up as the tutorial shows:
I don't receive any errors from the SSH log in Hyperion when I send the config or set it up at all.
I hope this information is enough to help me figure out why my LEDs won't turn on when I select Start in Hyperion.