Hyperbian + Hyperion ng + ezcap 269

Tyler983 · 14. September 2020

Woow, sure i can... Do you think new release will solve my issues?

TPmodding · 14. September 2020

there some points which are effected, so yes, think so

Tyler983 · 14. September 2020

I'll cross my fingers hoping it

TPmodding · 15. September 2020

it is out
https://github.com/hyperion-project/HyperBian/releases

Tyler983 · 15. September 2020

Wanderful. This evening, when I’ll be back from work I’ll do a fresh install of it and we’ll see. Thx a lot for the support @TPmodding

Tyler983 · 15. September 2020

@TPmodding in hurry i've done a fresh install of the new release, activated ssh and putt the sd in the rpi4. Setted all in auto, just activated the usb grabber.Still nothing, no swirl effect at the boot. In the evening, when i'll be at home, i'll test it with a debug command. Let's keep in touch

Tyler983 · 15. September 2020

@TPmodding i entered in terminal sudo journalctl -u hyperiond@pi.service and this is the message.

lines 1-2/2 (END)...skipping...

-- Logs begin at Thu 2019-02-14 10:11:59 GMT, end at Tue 2020-09-15 19:05:13 BST. --

-- No entries --

Anyway leds are still off

Lord-Grey · 15. September 2020

Hey
Could you do
hyperiond@pi.service

if I am not mistaken, with the latest Hyperbian Version from yesterday this was aligned to Standard.

Tyler983 · 15. September 2020

this is what I see...

lines 1-2/2 (END)...skipping...

-- Logs begin at Tue 2020-09-15 18:17:01 BST, end at Tue 2020-09-15 19:43:25 BST. --

-- No entries --

Paulchen-Panther · 15. September 2020

What is the output from:

Code

systemctl status hyperion.service

Tyler983 · 15. September 2020

@Paulchen-Panther

Sep 15 18:43:57 HyperBian systemd[1]: Started Hyperion ambient light systemd service.

Sep 15 19:12:05 HyperBian hyperiond[595]: 2020-09-15T19:12:05.205 hyperiond LEDDEVICE : <ERROR> Device disabled, device 'adalight' signals error: 'Timeout writing data to ttyACM0'

Sep 15 19:12:05 HyperBian [595]: Device disabled, device 'adalight' signals error: 'Timeout writing data to ttyACM0'

Paulchen-Panther · 15. September 2020

Please post these two consol outputs in full. thank you

Code

cat /etc/os-release

Code

sudo systemctl stop hyperion.service && ./usr/bin/hyperiond -d

Tyler983 · 15. September 2020

Thx a lot @Paulchen-Panther

This is what I have

Paulchen-Panther · 15. September 2020

I'm sorry about it. Was the wrong path. Please output:

Code

sudo systemctl stop hyperion.service && ./usr/share/hyperion/bin/hyperiond -d

Tyler983 · 15. September 2020

pi@HyperBian:~ $ sudo systemctl stop hyperion.service && ./usr/share/hyperion/bin/hyperiond -d

-bash: ./usr/share/hyperion/bin/hyperiond: No such file or directory

pi@HyperBian:~ $

Paulchen-Panther · 15. September 2020

I'll check it out. I'll get in touch with you. Thanks

Tyler983 · 15. September 2020

I restarted the pi cause I wasn't able to enter the webgui after your command lines

Paulchen-Panther · 15. September 2020

A point has crept into the execution order.
Now we should get output

Code

sudo systemctl stop hyperion.service && /usr/share/hyperion/bin/hyperiond -d

Tyler983 · 15. September 2020

This is what it shown

Paulchen-Panther · 15. September 2020

@Lord-Grey Ausgabe funktioniert. Alles auf auto gelassen.
HyperBian installiert -> Adalight angesteckt -> ausgeführt:

Code

pi@HyperBian:~ $ /usr/share/hyperion/bin/hyperiond -d
2020-09-15T20:32:25.507 hyperiond MAIN         : <INFO> Set user data path to '/home/pi/.hyperion'
2020-09-15T20:32:25.563 hyperiond DAEMON       : <DEBUG> PythonInit.cpp:44:PythonInit() | Initializing Python interpreter
2020-09-15T20:32:25.605 hyperiond SETTINGSMGR  : <DEBUG> SettingsManager.cpp:107:SettingsManager() | Settings database initialized
2020-09-15T20:32:25.606 hyperiond DAEMON       : <INFO> CEC handler created
2020-09-15T20:32:25.612 hyperiond EFFECTFILES  : <INFO> 39 effects loaded from directory :/effects/
2020-09-15T20:32:25.616 hyperiond EFFECTFILES  : <INFO> 22 effect schemas loaded from directory :/effects/schema/
2020-09-15T20:32:25.616 hyperiond EFFECTFILES  : <INFO> 0 effects loaded from directory /home/pi/.hyperion/custom-effects
2020-09-15T20:32:25.631 hyperiond SETTINGSMGR  : <DEBUG> SettingsManager.cpp:107:SettingsManager() | Settings database initialized
2020-09-15T20:32:25.632 hyperiond BLACKBORDER  : <DEBUG> BlackBorderProcessor.cpp:64:handleSettingsUpdate() | Set mode to: default
2020-09-15T20:32:25.632 hyperiond COMPONENTREG : <DEBUG> ComponentRegister.cpp:36:setNewComponentState() | Blackborder detector: enabled
2020-09-15T20:32:25.674 hyperiond DAEMON       : <INFO> set screen capture device to 'dispmanx'
2020-09-15T20:32:25.674 hyperiond DISPMANXGRAB : <DEBUG> Grabber.cpp:30:setVideoMode() | Set videomode to 0
2020-09-15T20:32:25.675 hyperiond DISPMANXGRAB : <INFO> Display opened with resolution: 1920x1080
2020-09-15T20:32:25.676 hyperiond DISPMANXGRAB : <DEBUG> Grabber.cpp:90:setWidthHeight() | Set new width: 80, height: 45 for capture
2020-09-15T20:32:25.676 hyperiond DAEMON       : <INFO> DISPMANX frame grabber created
2020-09-15T20:32:25.676 hyperiond V4L2:AUTO    : <DEBUG> Grabber.cpp:30:setVideoMode() | Set videomode to 0
2020-09-15T20:32:25.677 hyperiond V4L2:AUTO    : <INFO> Signal threshold set to: {12, 12, 12}
2020-09-15T20:32:25.677 hyperiond V4L2:AUTO    : <INFO> CEC detection is now disabled
2020-09-15T20:32:25.677 hyperiond V4L2:AUTO    : <INFO> Signal detection is now disabled
2020-09-15T20:32:25.677 hyperiond V4L2:AUTO    : <INFO> Signal detection area set to: 0.250000,0.250000 x 0.750000,0.750000
2020-09-15T20:32:25.678 hyperiond DAEMON       : <DEBUG> hyperiond.cpp:568:handleSettingsUpdate() | V4L2 grabber created
2020-09-15T20:32:25.678 hyperiond JSONSERVER   : <DEBUG> JsonServer.cpp:27:JsonServer() | Created instance
2020-09-15T20:32:25.679 hyperiond JSONSERVER   : <INFO> Started on port 19444
2020-09-15T20:32:25.679 hyperiond FLATBUFSERVE : <INFO> Started on port 19400
2020-09-15T20:32:25.680 hyperiond PROTOSERVER  : <INFO> Started on port 19445
2020-09-15T20:32:25.680 hyperiond WEBSERVER    : <DEBUG> WebServer.cpp:32:initServer() | Initialize Webserver
2020-09-15T20:32:25.681 hyperiond WEBSERVER    : <DEBUG> WebServer.cpp:32:initServer() | Initialize Webserver
2020-09-15T20:32:25.690 hyperiond LEDDEVICE    : <INFO> Start LedDevice 'adalight'.
2020-09-15T20:32:25.690 hyperiond LEDDEVICE    : <DEBUG> LedDevice.cpp:147:init() | deviceConfig: [{"colorOrder":"rgb","currentLedCount":26,"delayAfterConnect":0,"hardwareLedCount":1,"latchTime":30,"lightberry_apa102_mode":false,"output":"auto","rate":115200,"rewriteTime":1000,"type":"adalight"}]
2020-09-15T20:32:25.690 hyperiond COMPONENTREG : <DEBUG> ComponentRegister.cpp:36:setNewComponentState() | Smoothing: enabled
2020-09-15T20:32:25.691 hyperiond LEDDEVICE    : <DEBUG> LedDevice.cpp:403:setLatchTime() | LatchTime updated to 30ms
2020-09-15T20:32:25.691 hyperiond LEDDEVICE    : <DEBUG> LedDevice.cpp:423:setRewriteTime() | Refresh interval = 1000ms
2020-09-15T20:32:25.691 hyperiond LEDDEVICE    : <DEBUG> LedDevice.cpp:429:setRewriteTime() | RewriteTime updated to 1000ms
2020-09-15T20:32:25.691 hyperiond LEDDEVICE    : <DEBUG> ProviderRs232.cpp:36:init() | DeviceType   : adalight
2020-09-15T20:32:25.691 hyperiond LEDDEVICE    : <DEBUG> ProviderRs232.cpp:37:init() | LedCount     : 26
2020-09-15T20:32:25.691 hyperiond LEDDEVICE    : <DEBUG> ProviderRs232.cpp:38:init() | ColorOrder   : rgb
2020-09-15T20:32:25.691 hyperiond LEDDEVICE    : <DEBUG> ProviderRs232.cpp:39:init() | RefreshTime  : 1000
2020-09-15T20:32:25.691 hyperiond LEDDEVICE    : <DEBUG> ProviderRs232.cpp:40:init() | LatchTime    : 30
2020-09-15T20:32:25.691 hyperiond LEDDEVICE    : <DEBUG> ProviderRs232.cpp:52:init() | deviceName   : auto
2020-09-15T20:32:25.691 hyperiond LEDDEVICE    : <DEBUG> ProviderRs232.cpp:53:init() | AutoDevice   : 1
2020-09-15T20:32:25.692 hyperiond LEDDEVICE    : <DEBUG> ProviderRs232.cpp:54:init() | baudRate_Hz  : 115200
2020-09-15T20:32:25.692 hyperiond LEDDEVICE    : <DEBUG> ProviderRs232.cpp:55:init() | delayAfCon ms: 0
2020-09-15T20:32:25.692 hyperiond LEDDEVICE    : <DEBUG> LedDeviceAdalight.cpp:58:init() | Adalight header for 26 leds: Ada 0x00 0x19 0x4c
2020-09-15T20:32:25.692 hyperiond FLATBUFCONN  : <INFO> Connecting to Hyperion: 127.0.0.1:19401
2020-09-15T20:32:25.693 hyperiond EFFECTENGINE : <INFO> Run effect "Rainbow swirl fast" on channel 0
2020-09-15T20:32:25.694 hyperiond EFFECTENGINE : <DEBUG> EffectEngine.cpp:183:runEffectScript() | Start the effect: name [Rainbow swirl fast], smoothCfg [2]
2020-09-15T20:32:25.695 hyperiond HYPERION     : <DEBUG> PriorityMuxer.cpp:159:registerInput() | Register new input 'System/EFFECT' with priority 0 as inactive
2020-09-15T20:32:25.695 hyperiond HYPERION     : <INFO> Initial foreground effect 'Rainbow swirl fast' started
2020-09-15T20:32:25.695 hyperiond EFFECTENGINE : <INFO> Run effect "Warm mood blobs" on channel 254
2020-09-15T20:32:25.696 hyperiond EFFECTENGINE : <DEBUG> EffectEngine.cpp:183:runEffectScript() | Start the effect: name [Warm mood blobs], smoothCfg [2]
2020-09-15T20:32:25.696 hyperiond HYPERION     : <DEBUG> PriorityMuxer.cpp:159:registerInput() | Register new input 'System/EFFECT' with priority 254 as inactive
2020-09-15T20:32:25.696 hyperiond HYPERION     : <INFO> Inital background effect 'Warm mood blobs' started
2020-09-15T20:32:25.697 hyperiond HYPERION     : <DEBUG> PriorityMuxer.cpp:159:registerInput() | Register new input 'System/GRABBER' with priority 250 as inactive
2020-09-15T20:32:25.697 hyperiond COMPONENTREG : <DEBUG> ComponentRegister.cpp:36:setNewComponentState() | Framegrabber: enabled
2020-09-15T20:32:25.697 hyperiond Dispmanx     : <DEBUG> GrabberWrapper.cpp:48:start() | Grabber start()
2020-09-15T20:32:25.698 hyperiond BOBLIGHT     : <DEBUG> BoblightServer.cpp:28:BoblightServer() | Instance created
2020-09-15T20:32:25.698 hyperiond HYPERION     : <INFO> Hyperion instance 'First LED Hardware instance' has been started
2020-09-15T20:32:25.705 hyperiond WEBSERVER    : <DEBUG> WebServer.cpp:90:handleSettingsUpdate() | Apply Webserver settings
2020-09-15T20:32:25.705 hyperiond WEBSERVER    : <DEBUG> WebServer.cpp:108:handleSettingsUpdate() | Set document root to: :/webconfig
2020-09-15T20:32:25.705 hyperiond WEBSERVER    : <DEBUG> WebServer.cpp:90:handleSettingsUpdate() | Apply Webserver settings
2020-09-15T20:32:25.705 hyperiond WEBSERVER    : <INFO> Started on port 8090 name 'Hyperion Webserver'
2020-09-15T20:32:25.705 hyperiond WEBSERVER    : <DEBUG> WebServer.cpp:108:handleSettingsUpdate() | Set document root to: :/webconfig
2020-09-15T20:32:25.741 hyperiond LEDDEVICE    : <INFO> found serial device: ttyUSB0
2020-09-15T20:32:25.741 hyperiond LEDDEVICE    : <INFO> Opening UART: ttyUSB0
2020-09-15T20:32:25.742 hyperiond LEDDEVICE    : <DEBUG> ProviderRs232.cpp:141:tryOpen() | _rs232Port.open(QIODevice::ReadWrite): ttyUSB0, Baud rate [115200]bps
2020-09-15T20:32:25.788 hyperiond LEDDEVICE    : <DEBUG> ProviderRs232.cpp:146:tryOpen() | portName:          ttyUSB0
2020-09-15T20:32:25.788 hyperiond LEDDEVICE    : <DEBUG> ProviderRs232.cpp:147:tryOpen() | systemLocation:    /dev/ttyUSB0
2020-09-15T20:32:25.788 hyperiond LEDDEVICE    : <DEBUG> ProviderRs232.cpp:148:tryOpen() | description:       USB2.0-Serial
2020-09-15T20:32:25.789 hyperiond LEDDEVICE    : <DEBUG> ProviderRs232.cpp:149:tryOpen() | manufacturer:      1a86
2020-09-15T20:32:25.789 hyperiond LEDDEVICE    : <DEBUG> ProviderRs232.cpp:150:tryOpen() | productIdentifier: 0x7523
2020-09-15T20:32:25.789 hyperiond LEDDEVICE    : <DEBUG> ProviderRs232.cpp:151:tryOpen() | vendorIdentifier:  0x1a86
2020-09-15T20:32:25.789 hyperiond LEDDEVICE    : <DEBUG> ProviderRs232.cpp:152:tryOpen() | serialNumber:
2020-09-15T20:32:25.794 hyperiond COMPONENTREG : <DEBUG> ComponentRegister.cpp:36:setNewComponentState() | LED device: enabled
2020-09-15T20:32:25.802 hyperiond HYPERION     : <DEBUG> PriorityMuxer.cpp:238:setInputImage() | Priority 250 is now active
2020-09-15T20:32:25.802 hyperiond HYPERION     : <DEBUG> PriorityMuxer.cpp:333:setCurrentTime() | Set visible priority to 0
2020-09-15T20:32:25.803 hyperiond HYPERION     : <DEBUG> Hyperion.cpp:538:handlPriorityChangedLedDevice() | priority[0], previousPriority[255]
2020-09-15T20:32:25.803 hyperiond HYPERION     : <DEBUG> Hyperion.cpp:548:handlPriorityChangedLedDevice() | new source available -> switch LED-Device on
2020-09-15T20:32:25.811 hyperiond WEBSERVER    : <DEBUG> WebServer.cpp:174:handleSettingsUpdate() | Setup SSL certificate
2020-09-15T20:32:25.812 hyperiond WEBSERVER    : <DEBUG> WebServer.cpp:190:handleSettingsUpdate() | Setup private SSL key
2020-09-15T20:32:25.813 hyperiond WEBSERVER    : <INFO> Started on port 8092 name 'Hyperion Webserver'
2020-09-15T20:32:25.875 hyperiond HYPERION     : <DEBUG> PriorityMuxer.cpp:198:setInput() | Priority 254 is now active
2020-09-15T20:32:25.885 hyperiond HYPERION     : <DEBUG> PriorityMuxer.cpp:238:setInputImage() | Priority 0 is now active
2020-09-15T20:32:28.512 hyperiond WEBSOCKET    : <DEBUG> WebSocketClient.cpp:30:WebSocketClient() | New connection from ::ffff:192.168.0.90
2020-09-15T20:32:28.513 hyperiond WEBSOCKET    : <DEBUG> JsonAPI.cpp:81:handleInstanceSwitch() | Client '::ffff:192.168.0.90' switch to Hyperion instance 0
2020-09-15T20:32:28.834 hyperiond HYPERION     : <DEBUG> PriorityMuxer.cpp:298:setCurrentTime() | Timeout clear for priority 0
2020-09-15T20:32:29.084 hyperiond HYPERION     : <DEBUG> PriorityMuxer.cpp:333:setCurrentTime() | Set visible priority to 250
2020-09-15T20:32:29.085 hyperiond HYPERION     : <DEBUG> Hyperion.cpp:538:handlPriorityChangedLedDevice() | priority[250], previousPriority[0]

Alles anzeigen

Jetzt mitmachen!